Delta 45, F-25, 35, 30, 40 warranty Section VII Fuel Piping, Recommended Gas Supply Piping

Page 33

Fuel Piping

SECTION VII - Fuel Piping

Gas Supply Piping Connection

NOTICE

The gas supply piping must be installed in accordance to all applicable local, state and national codes and utility requirements.

1.Remove the burner jacket hood. Refer to Fig. 15 to pipe gas supply to the burner.

a.Install a pipe union at the factory sup- plied gas nipple, for ease of service.

b.Install a manual shutoff valve in the gas supply piping as shown in Fig. 15. For installations in Canada the installer must tag and identify the main shutoff valve.

c.Install a drip leg on the gas supply line prior to connecting to the ELITE gas train as shown in Fig. 15.

2.Support the gas piping using hangers. Do not support the piping by the unit or its components.

3.Purge all air from the gas supply piping.

4.Before placing the ELITE into operation, check and test all connections for leaks.

Close the manual shutoff valve during any pressure test with less than 13”w.c..

Disconnect the ELITE and its gas valve from the gas supply piping during any pressure test greater than 13”w.c..

WARNING

Do not check for gas leaks with an open flame. Use a gas detection device or bub- ble test. Failure to check for gas leaks can cause severe personal injury, death or substantial property damage.

5.Use pipe dope compatible with natural and propane gases. Apply sparingly only to the male threads of pipe joints so that pipe dope does not block gas flow.

WARNING

Failure to apply pipe dope as detailed above can result in severe personal injury, death or substantial property damage.

WARNING

Use a two-wrench method of tightening gas piping near the unit and its gas valve. Use one wrench to prevent the gas valve line connection from turning and the sec- ond to tighten adjacent piping. Failure to support the gas valve connection pip- ing could damage the valve and the gas line components.

Fig. 15: Recommended Gas Supply Piping

28

Page 32 Page 34
Image 33
Page 32 Page 34
Contents For Your Safety Installation a N D M a I N T E N a N C ETable of Contents Section V Primary Piping Section Viii Internal Wiring Section Xiii CHECK-OUT Procedures Product & Safety Information HOT Troubleshooting Ing label when inquiring about service orBer and the serial number from the rat Triangle Tube accepts no liability for anyOperating Restrictions Boiler Replacement Section I Pre-Installation ItemsCode Compliance Determining Product LocationResidential Garage Installations Section II Providing Air for Combustion and Ventilation Removal of an Existing Boiler from a Common Vent System Section III Unit Preparation Hydrostatic Test ProceduresHandling Instructions Hydrostatic Pressure TestCompletion of Hydrostatic Test and Draining Section IV Domestic Piping Temperature / Pressure Relief ValveGeneral Piping Requirements Domestic Supply PressureDomestic Piping Storage Tank Application Multiple Units InstallationTR/SMART Series Application Domestic Piping DiagramsElite With Recirculation Elite with Storage Tank Domestic PipingSection V Primary Piping Closet Zero Clearance Applications Sizing Primary PipingSystem Piping Zone Circulators Primary Piping Near Appliance Piping Install balancing valves to Primary Piping Low Temperature Radiant System Primary Piping Multi Units Installation Repair any damaged chimney mor- tar or joints Section VI VentingOil Vent Direct Vent Applications Gas Venting -General Requirements Masonry and Metal ChimneysType B Vent Systems Vent Connectors Recommended Gas Supply Piping Section VII Fuel PipingNatural Gas Supply Pressure Requirements Pipe Sizing Natural GasPipe Sizing Propane Gas Propane Gas Supply Pressure RequirementsGeneral Oil Piping Guidelines Elite Factory Internal Wiring Section Viii Internal WiringWire Color Code Installation Compliance Section IX External WiringOutdoor Temperature Limit Line Voltage ConnectionsMultiple Zone Field Wiring Using Zone Valves Field wiring with zone circulators Typical Zone Relay Panel Wiring Section X Start Up Preparation Filling the Outer Primary Tank and System Check Low Water Cut-Off Device Section XI Start-Up Procedures Final Checks Before Start-upElite Start-up Recommended Combustion Levels Recommended Primary Thermostat Setting Section XII Temperature LimitsTemperature Limits Section XIII- Check-Out Procedures Section XIV Installation Record Section Xvii Replacement Parts Jacket Components Control Panel Components Electrical Panel Components Specifications Elite Data Maxi-flo Pool and Spa Heat Exchangers TTP Brazed Plate Heat Exchangers

45, 30, 35, 40, F-25 specifications

Delta 40, F-25, F-30, F-35, and F-45 represent a new generation of aircraft designed to meet the evolving demands of modern aviation. These aircraft are equipped with advanced technologies, making them suitable for various missions, including cargo transport, surveillance, and multirole combat operations. Each model in this series comes with its own set of features and capabilities.

The Delta 40 stands as a versatile platform known for its impressive range and payload capacity. Its advanced avionics system ensures enhanced situational awareness and operational efficiency. The aircraft employs composite materials for improved fuel efficiency and reduced maintenance costs. Furthermore, Delta 40 is equipped with state-of-the-art navigation systems that include GPS, inertial navigation, and terrain awareness features.

The F-25 is designed with a focus on agility and speed. It features advanced thrust vectoring technology that allows for greater maneuverability, making it effective in air-to-air combat situations. The aircraft leverages stealth technology, incorporating radar-absorbing materials that reduce its visibility to enemy radar systems. This model also includes advanced electronic warfare capabilities for defensive operations.

Moving on to the F-30, this aircraft serves as a heavy-lift solution, optimized for cargo transport. Its spacious cargo bay can accommodate a wide range of freight, and its loading ramp facilitates quick turnaround times for ground operations. The F-30 utilizes a fly-by-wire control system to enhance stability and control during flight. Additionally, this model is equipped with advanced communication systems that allow for seamless integration into joint operations.

The F-35 integrates cutting-edge technologies to provide multirole capabilities. It boasts an advanced sensor suite that enables real-time data sharing among allied forces. The aircraft's stealth capabilities and advanced electronic warfare systems make it a formidable presence on the battlefield. Its interoperability with various platforms enhances the overall effectiveness of joint missions.

Finally, the F-45 combines the best features of its predecessors and introduces several enhancements. It leverages artificial intelligence for mission planning and execution, streamlining complex operations. The aircraft is also equipped with the latest in propulsion technology, resulting in improved fuel efficiency and performance at high altitudes.

Each of these aircraft models is designed with specific missions in mind, showcasing a commitment to innovation and technological advancement in aviation. With features that enhance their performance, adaptability, and combat readiness, the Delta 40, F-25, F-30, F-35, and F-45 represent the future of aviation technology. Their development signifies an important step toward maintaining technological superiority in both military and commercial aviation sectors.
Top Page Image Contents