CLEANING |
| WARNING | |
AND | WARNING ICONG 001 | ||
Turn off heater and let cool before cleaning. | |||
MAINTENANCE |
|
|
|
|
| ||
| WARNING ICONG 001 | CAUTION | |
|
| ||
You must keep control areas, burner, and circulating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualified service person. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, etc.
ODS/PILOT AND BURNER ORIFICE
• Use a vacuum cleaner, pressurized air, or small, soft bristled brush to clean.
CABINET
Air Passageways
•Use a vacuum cleaner or pressurized air to clean.
Exterior
•Use a soft cloth dampened with a mild soap and water mixture. Wipe the cabinet to remove dust.
TROUBLE- |
|
| WARNING ICONG 001WARNING |
|
|
|
|
|
SHOOTING |
|
|
|
|
|
|
| |
Turn off heater and let cool before servicing. Only a qualified |
|
| ||||||
Note: All troubleshooting | service person should service and repair heater. |
|
| |||||
|
|
|
|
|
|
|
| |
items are listed in order of |
|
|
|
|
|
|
|
|
|
| WARNING ICONG 001CAUTION |
|
|
|
|
| |
operation. |
|
|
|
|
|
|
| |
| Never use a wire, needle, or similar object to clean ODS/pilot. This |
|
| |||||
| can damage ODS/pilot unit. |
|
|
|
|
| ||
|
|
|
|
|
|
|
| |
| OBSERVED | POSSIBLE |
|
|
|
|
| |
| PROBLEM | CAUSE | REMEDY |
|
| |||
|
|
|
|
|
|
|
| |
| When ignitor button | 1. | Ignitor electrode posi- | 1. | Replace ignitor |
|
| |
| is pressed and control |
| tioned wrong |
|
|
|
|
|
| knob is pressed in | 2. | Ignitor electrode broken | 2. | Replace ignitor |
|
| |
| and turned to the | 3. | Ignitor electrode not | 3. | Reconnect ignitor cable | |||
| PILOT position, |
| connected to ignitor |
|
|
|
|
|
| there is no spark at |
| cable |
|
|
|
|
|
| ODS/pilot | 4. | Ignitor cable pinched or | 4. | Free ignitor cable if |
|
| |
|
|
| wet |
| pinched by any metal or | |||
|
|
|
|
| tubing. Keep ignitor |
|
| |
|
| 5. Piezo ignitor nut is loose |
| cable dry |
|
| ||
|
|
|
| 5. | Tighten nut holding |
|
| |
|
|
|
|
| piezo ignitor to heater |
|
| |
|
|
|
|
| cabinet. Nut is located |
|
| |
|
|
|
|
| inside heater cabinet at | |||
|
| 6. | Broken ignitor cable |
| top |
|
| |
|
| 7. | Bad piezo ignitor | 6. | Replace ignitor cable |
|
| |
|
|
|
| 7. | Replace control valve |
|
| |
|
|
|
|
| (piezo is part of control | |||
|
|
|
|
| valve) |
|
| |
|
|
|
|
| Continued |
| 21 | |
|
|
|
|
|
|
| ||
100846 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |