Desa CGB3930NRA AIR for Combustion Ventilation, Determining FRESH-AIR Flow for Heater Location

Page 5

OWNER’S MANUAL

AIR FOR

COMBUSTION AND

VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Confined or Unconfined Space

Use this work sheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between the rooms.

1.Determine the volume of the space (length x width x height).

Length x Width x Height = _________________ cu. ft. (volume of space)

Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2.Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.

_________________ (volume of space) ÷ 50 cu. ft. = (Maximum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space can support)

3.Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free heater

____________________ Btu/Hr

 

 

 

 

Gas water heater*

____________________ Btu/Hr

Example:

 

 

 

Gas furnace

____________________ Btu/Hr

Gas water heater

 

40,000

Btu/Hr

 

 

 

Vented gas heater

____________________ Btu/Hr

Vent-free heater

+

39,000

Btu/Hr

Gas fireplace logs

____________________ Btu/Hr

Total

=

79,000

Btu/Hr

Other gas appliances* + ____________________ Btu/Hr

 

 

 

 

Total

= ____________________ Btu/Hr

 

 

 

 

*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4.Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_________________ Btu/Hr (maximum the space can support)

_________________ Btu/Hr (actual amount of Btu/Hr used)

Example: 51,200 Btu/Hr (maximum the space can support) 79,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:

A.Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin- ing room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.

B.Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.

C.Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no additional fresh air ventilation.

WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the National Fuel Gas Code, ANS Z223.1, 1992, Section 5.3 or applicable local codes.

Continued

105677

5

Image 5
Contents What to do if YOU Smell GAS Remote ReadyUnvented Natural GAS LOG Heater Safety Information Remote Control Accessories Product FeaturesProduct Identification Local CodesConfined Space and Unconfined Space Providing Adequate VentilationUnusually Tight Construction Determining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Check GAS Type InstallationMinimum Fireplace Clearance to Combustible Materials LOG Sizing RequirementsMinimum Noncombustible Material Clearances Unvented Natural GAS LOG Heater InstallationMantel Clearances Determining Minimum Mantel Clearances When Using a HoodFloor Clearances Determining Minimum Mantel ClearancesInstallation Items Needed Installing Damper Clamp Accessory for Vented OperationInstalling Heater Base Assembly Attaching Flexible Gas Hose to Heater Connecting to GAS SupplyChecking GAS Connections Installing Remote RE- Ceiver UnitInstalling 9-Volt Battery in Receiver Installing Wireless Remote Control AccessoryInstalling Logs CGD3924NRA Tered over the burner U bend Installing Logs on Models CGB3924PRA and CGB3930PRALighting Instructions For Your Safety Read Before LightingOperating Heater Unvented Natural GAS LOG Heater Operating Manual Lighting ProcedureTo Turn OFF GAS To Appliance Optional Remote OperationMain Burner Inspecting BurnersPilot Flame Pattern Service Hints Unvented Natural GAS LOG Heater Cleaning and MaintenanceTechnical Service Cleaning Burner Injector Holder and Pilot AIR Inlet HoleObserved Problem Possible Cause Remedy TroubleshootingMaintenance, Unvented Natural GAS LOG Heater TroubleshootingGas leak. See Warning statement at CGD3924NRA Unvented Natural GAS LOG Heater Illustrated Parts BreakdownKEY Part Number Description QTY Parts ListCGB3924NRA CGB3930NRA KEY CGB3924NRA CGB3930NRA Part Number Description QTY Parts Under Warranty Unvented Natural GAS LOG Heater Replacement PartsParts not Under Warranty Parts CentralWiring Diagram AccessoriesSpecifications Warranty Information