Installing GAS LOG Heater Into Stove

SUN VALLEY STOVE COMPANY

VENT-FREE PROPANE/LP GAS STOVE HEATER

INSTALLATION

Continued

INSTALLING GAS LOG HEATER INTO STOVE

CAUTION: Do not remove the metal data plates attached to the heater base assembly. The data plates contain important warranty information.

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

CAUTION:Afterinstallationand periodically thereafter, check to en- surethatnoflamecomesincontact with any log. With the heater set to High, check to see if flames contact any log. If so, reposition logs ac- cording to the log installation in- structions in this manual. Flames contacting logs will create soot.

1.Remove log and gas log heater from carton. Note: Do not pick up gas log heater by the burner itself. This could damage heater. Always handle the gas log heater by the heater base only.

2.Remove all protective packaging applied to log and gas log heater for shipment.

3.Check all items for any shipping dam- age. If damaged, promptly inform dealer where you bought heater.

4.If not already removed, remove back panel from assembled stove body (see Figure 5, page 8). Use an adjustable wrench or a 10 mm socket. Remove six

(6) bolts and washers. Keep bolts and washers to reattach back panel later.

5.Set gas log heater inside stove. Make sure control knob extension passes through bottom front opening (see Figure 13).

6.Align outside holes on heater base with four (4) mounting holes on the stove bottom (see Figure 13).

7.Fasten heater base to stove bottom with #10-24 x .50 bolts and hex nuts pro- vided with gas log heater (see Figure 14). Attachment hardware is factory packed inside plastic bag with installa- tion manual and owner’s registration card. Push bolt through heater base mounting hole and through stove bot- tom. Connect hex nut to bolt on under- side of stove bottom. The bolt hex head is for a 5/16" socket and the hex nuts are for a 3/8" socket. If sockets are not available, use adjustable wrenches.

8.Set one-piece log on heater base as shown in Figure 15. Make sure middle section at bottom of log is seated into "U" shaped cutout in center of heater base. Log will fit securely on base.

IMPORTANT: Make sure log does not cover any burner ports and does not touch the stove cavity (see Figure 16).

9.Fasten back panel to stove with six (6) M6 x 1.20mm bolts and washers. Make sure product identification label is located on the outside lower left-hand corner. Note: Do not overtighten bolts. Porce- lain on back panel may crack.

10.Place freestanding stove in desired po- sition in room. Be sure to maintain clearances to combustibles as outlined on page 7.

Bottom

Front

Opening

		Burner
Bolt	Heater	Stove Bottom
	Base	Stove Bottom
	Base

Figure 13 - Placing Heater Base In Stove Cavity (Appearance May Vary Depending on Model)

				Heater
Bolt				Base
Bolt

							Stove
Hex Nut


							Bottom

Figure 14 - Fastening Heater Base to Stove Drop Bottom

One-Piece

Log Set

Middle

Section at

Bottom of

Log Set

Burner

"U" Shaped

Cutout in

Chassis

Heater Base

Figure 15 - Installing One-Piece Stove

Log Set (Remote-Ready Log Heater

Shown)

Burner Porting Areas (double slotted rectangular openings

	Safety Pilot Location	One-Piece
	Safety Pilot Location	Log Set
		Log Set

Figure 16 - Top View of One-Piece Log Set on Gas Log Heater

For more information, visit www.desatech.com

105986