Desa HDVF3018N, HDVF3018P Troubleshooting, Observed Problem Possible Cause Remedy

Page 21

Troubleshooting

WARNING: Turn off heater and let cool before servicing. Only a qualified service person should service and repair heater.

CAUTION: Never use a wire, needle or similar object to clean ODS/pilot. This can damage ODS/pilot unit.

Note: All troubleshooting items are listed in order of operation.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

 

 

 

 

 

 

 

When ignitor button is pressed,

1. Ignitor electrode not con-

1.

Reconnect ignitor cable

there is no spark at ODS/pilot

2.

nected to ignitor cable

2.

Free ignitor cable if pinched

 

 

Ignitor cable pinched or wet

 

 

 

 

 

by any metal or tubing. Keep

 

 

3.

Piezo ignitor nut is loose

3.

ignitor cable dry

 

 

Tighten nut holding piezo ignitor

 

 

 

 

 

to base panel of log set. Nut is

 

 

4.

Broken ignitor cable

4.

located behind base panel

 

 

Replace ignitor cable

 

 

5.

Bad piezo ignitor

5.

Replace piezo ignitor

 

 

6.

Ignitor electrode broken

6.

Replace pilot assembly

 

 

7. Ignitor electrode positioned wrong

7.

Replace pilot assembly

 

When ignitor button is pressed,

1. Gas supply turned off or equip-

1.

Turn on gas supply or open

 

there is spark at ODS/pilot but

 

ment shutoff valve closed

2.

equipment shutoff valve

no ignition

2. Control knob not in PILOT

Turn control knob to PILOT

 

 

3.

position

3.

position

 

 

Control knob not pressed in

Press in control knob while in

 

 

4.

while in PILOT position

4.

PILOT position

 

 

Air in gas lines when in-

Continue holding down con-

 

 

 

stalled

 

trol knob. Repeat igniting op-

 

 

5.

Depleted gas supply (propane/

5.

eration until air is removed

 

 

Contact local propane/LP gas

 

 

6.

LP only)

6.

company

 

 

ODS/pilot is clogged

Clean ODS/pilot (see Cleaning

 

 

 

 

 

and Maintenance, page 19) or

 

 

7. Gas regulator setting is not

7.

replace ODS/pilot assembly

 

 

Replace gas regulator

 

 

 

correct

 

 

 

 

ODS/pilot lights but flame

1. Control knob not fully pressed in

1.

Press in control knob fully

 

goes out when control knob is

2. Control knob not pressed in

2.

After ODS/pilot lights, keep con-

released

3.

long enough

3.

trol knob pressed in 30 seconds

 

 

Equipment shutoff valve not

Fully open equipment shutoff

 

 

4.

fully open

4.

valve

 

 

Pilot flame not touching ther-

A) Contact local propane/LP

 

 

 

mocouple, which allows ther-

 

or natural gas company

 

 

 

mocouple to cool, causing

 

B) Clean ODS/pilot (see

 

 

 

pilot flame to go out. This

 

 

 

 

problem could be caused by

 

Cleaning and Maintenance,

 

 

 

one or both of the following:

 

page 19) or replace ODS/pilot

 

 

 

A) Low gas pressure

 

assembly

 

 

 

B) Dirty or partially clogged

 

 

 

 

 

 

5.

ODS/pilot

5.

Hand tighten until snug, then

 

 

Thermocouple connection

 

 

6.

loose at control valve

6.

tighten 1/4 turn more

 

 

Thermocouple damaged

Replace pilot assembly

 

 

7.

Control valve damaged

7.

Replace control valve

119421-01A

www.desatech.com

21

Image 21
Contents Variable Manually Controlled Models Also Design-Certified As Vented Decorative AppliancesSafety Information Table of ContentsSafety Information Local Codes Product Identification Product FeaturesUnpacking Air for Combustion VentilationAIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Check GAS Type InstallationInstallation Installation and ClearancesVent-Free Operation Only Marble, Tile, etc. Above Fireplace Mantel ClearancesFloor Clearances Installing Damper Clamp Accessory for Vented OperationInstallation Items Needed Installing Heater Base AssemblyChimney Minimum Permanent Area of Various Standard Round FluesAttaching Base Assembly to Fireplace Floor Dual Burner Model Connecting to GAS SupplyChecking GAS Connections Propane/LPNatural Installing Logs Pressure Testing Heater Gas ConnectionsTest Pressures Equal To or Less Than Psig 3.5 kPa Installing Front Log #1 For Your Safety Read Before LIGHTING  Operating Heater LIGHTING INSTRUCTIONS  Operating Heater  MANUAL Lighting Procedure VARIABLE Control Operation  TO Turn OFF GAS to APPLIANCE Inspecting Burners Cleaning MaintenancePilot Flame Pattern Burner Primary AIR HolesBlow air into the primary air holes on the injector holder LogsObserved Problem Possible Cause Remedy TroubleshootingMaintenance, TroubleshootingStatement above Gas leak. See WarningTechnical Service SpecificationsService Hints Replacement PartsAccessories Equipment Shutoff Valve GA5010Fireplace Hood Variable Manually-Controlled Models HDVF3018P and HDVF3018N Illustrated Parts BreakdownParts List Warranty Information Keep this WarrantyLimited Warranty VENT-FREE GAS LOG Heaters

HDVF3018N, HDVF3018P specifications

The Desa HDVF3018P and HDVF3018N are advanced heating solutions that exemplify innovation and efficiency in the heating appliance market. They are designed to provide reliable and effective heating for residential and commercial spaces, ensuring comfort during colder months while also prioritizing energy efficiency.

One of the standout features of the HDVF3018 series is its powerful heat output. With an impressive BTU rating, these units are capable of efficiently warming large areas, making them ideal for both homes and businesses. This makes them a popular choice for those looking to maintain a comfortable environment during winter.

In terms of design, the HDVF3018P and HDVF3018N boast sleek, modern aesthetics that allow them to blend seamlessly with various interior styles. Their compact footprints make them suitable for smaller spaces without sacrificing performance. Additionally, these units are equipped with advanced safety features, including automatic shut-off mechanisms that ensure reliable operation without compromising user safety.

The HDVF3018 series incorporates cutting-edge technology to optimize heating efficiency. For instance, they utilize a variable speed blower, which not only enhances heat distribution but also reduces energy consumption. This feature helps residents and businesses save on heating costs while decreasing their environmental impact.

Another notable characteristic of these units is their user-friendly controls. The HDVF3018P and HDVF3018N come with intuitive interfaces that allow users to easily adjust temperature settings and programming schedules. This ensures that the heating systems operate at desired levels without needing constant manual adjustments.

In terms of fuel options, the HDVF3018 series is versatile, catering to various preferences and needs. Whether using propane, natural gas, or other fuel types, these units provide flexibility for users to choose the best option for their specific heating requirements.

Furthermore, both models are engineered with durability in mind. High-quality materials contribute to their longevity, making them a worthwhile investment for those seeking dependable heating solutions.

In summary, the Desa HDVF3018P and HDVF3018N deliver a powerful combination of reliable performance, modern design, and advanced technology. Their ability to efficiently heat spaces while providing user-friendly operation and safety make them excellent choices for anyone in need of a high-quality heating appliance.