Quadra-Fire QV36A-FB Appliance Preparation, Removing Non-combustible Facing Mate- rial Assembly

Page 20

7 Appliance Preparation

A.Removing Non-combustible Facing Mate- rial Assembly

The non-combustible assembly is located on the back side of appliance.

CAUTION

Handle with care

•Non-combustible material may be damaged if dropped.

•Hold non-combustible pieces in place.

•Remove and save two screws from upper bracket.

•Remove non-combustible pieces.

•Remove and save three screws from lower bracket.

•Discard brackets.

•Replace screws in holes where brackets were attached to appliance.

CUT LINE

BEND TABS UP

Figure 7.2. Bend Tabs and Cut Insulation.

3.Discard the Heat-Zone®cover plate and insulation piece that was cut out. See Figure 7.3. With a self- tapping screw or drill bit, drill out the three holes on the cover plate of the appliance. This will make it easier to mount the Heat-Zone®Gas collar.

B. Installing the Optional Heat-Zone®Gas

Kit

Before installing finishing materials, use these instructions to attach the Heat-Zone®Gas kit to the top of the QV36A-FB.

CAUTION

Sharp Edges

• Wear protective gloves and safety glasses during installation.

1.Remove the four screws that attach the Heat Zone® Cover Plate to the top of the appliance.

COVER PLATE HOLES

REMOVE SCREWS

Figure 7.1. Remove Screws.

2.Bend the four pre-cut tabs up to expose the top of the appliance. Place the Heat-Zone®cover plate on the insulation inside the unit centered between the three pre-cut tabs that are the same size as shown in Figure 7.2. Use the Heat-Zone®cover plate as a template and cut around it carefully with a utility knife.

Figure 7.3.

4.Remove the four screws securing the cover plate to the inside of the appliance and discard them along with the cover plate. See Figure 7.4.

Figure 7.4.

20

Quadra-Fire • Expression 36 (QV36A-FB) • 2062-900 Rev. S • 11/11

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Hot glass will cause burns Model Expression 36 QV36A-FBWhat to do if you smell gas Congratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of MassachusettsDesign and Installation Considerations Getting StartedTools and Supplies Needed Inspect Appliance and ComponentsInspect Firebox Framing and Clearances Selecting Appliance LocationModel 41-1/2 17-1/4 45-1/4 QV36A-FBConstructing the Appliance Chase ClearancesMantel Projections Fire Risk Odor Risk254 1321 438 1054 825 914 Clearance to Combustibles17-1/4 41-1/2 32-1/2 See .4 for specific clearances Termination LocationsVent Termination Minimum Clearances Covered Alcove Applications Vent Information and Diagrams Vent Table KeyMeasuring Standards Use of ElbowsVent Diagrams Top Vent Horizontal Termination One Elbow Two ElbowsMinimum Maximum 2 ftTop Vent Horizontal Termination Three Elbows VT Min HT MaxMust be installed prior to attaching a 90 elbow Top Vent Vertical Termination Three Elbows Min MaxFeet then the total vent run can be Extended to 40 feetVent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall PenetrationVertical Penetration Framing Installing the Ceiling FirestopInstalling Attic Shield Appliance Preparation Removing Non-combustible Facing Mate- rial Assembly B. Installing the Optional Heat-ZoneGas Kit Backer Securing and Leveling the ApplianceFire Risk Prevent contact with sagging, loose insulation Installing Non-combustible Facing Material 10 Complete Installation of Non-combustibleInstalling Vent Pipe Assembly of Vent SectionsAttaching Vent to the Firebox Assembly Assembling Pipe SectionsAssembling Minimum Installations MI Sections Assembling DVP-12A Slip SectionsHorizontal Sections Disassembly of Vent SectionsSecuring the Vent Sections Vertical Sections Installing Heat Shield and Horizontal Termination Cap Installing the Horizontal Termination CapHeat Shield Requirements for Horizontal Termination Important Notice Heat shields may not be field constructedFoot minimum in snow regions Installing Roof Flashing and Vertical Ter- mination CapRoof Pitch Min. Ft Assembling and Installing Storm Collar Sharp EdgesGas Information Fuel Conversions Gas ConnectionGas Pressures Pressure Natural Gas PropaneHigh Altitude Installations Recommendation for Wire Electrical InformationOptional Accessories Requirements QWSK-MLT Wall Switch Kit IntroductionInstallation precautions To Replace a Light BulbInstallation instructions Determine location Wiring the wall switchFor units with factory installed rocker switch Operating InstructionsSetting Flame Height/manifold pressure Wall Switch Button OperationTemperature Button SET Set Temperature ButtonJunction Box Installation Junction Box DetailFinishing Facing MaterialFacing Requirements FrontsAppliance Setup Clean the ApplianceAccessories Ember PlacementLog Assembly LOGS-2062 Positioning the LogsLOG #3 SRV2062-703 LOG #1 SRV2062-701LOG #2 SRV2062-702 LOG #6 SRV340-705 LOG #4 SRV330-706LOG #5 SRV330-704 Glass Assembly Removing Glass AssemblyReplacing Glass Assembly Burner Removal Only for ServicingAir Shutter Setting Grilles and TrimOperating Instructions Before Lighting ApplianceLighting Appliance IPI Ignition Final inspection byAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Troubleshooting Symptom Possible Cause Corrective ActionIntelliFire Ignition System Noise, but spark may not be present at pilot hoodCracked, damaged, or loose. Verify connection from sensor Maintaining and Servicing Appliance Maintenance Tasks Inspect Maintenance TasksLocation Inches Millimeters Appliance Dimension DiagramReference Materials Vent Components Diagrams DVP-AS2Horizontal Termination Cap DVP vent componentsRF6M RF12M Service Parts Log Set AssemblyAt Depot Direct Vent Gas Fireplace#17 Valve Assembly Be ordered from an authorized dealerService Parts List StockedLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Contact Information Do not Discard this Manual

QV36A-FB specifications

The Quadra-Fire QV36A-FB is a remarkable direct vent gas fireplace that combines beauty, efficiency, and innovative technology to create a cozy ambiance in any home. This fireplace is designed for those seeking an aesthetically pleasing yet highly functional heating solution.

One of the standout features of the QV36A-FB is its impressive heating capacity. With the ability to produce up to 34,000 BTUs, it effectively warms spaces of various sizes, making it suitable for both small and large living areas. Its impressive efficiency rating maximizes heat output while minimizing gas consumption, ensuring that homeowners can enjoy warmth without the worry of excessive energy bills.

The QV36A-FB employs a direct venting system, allowing for safe and efficient operation. This system draws air from outside for combustion, which is particularly beneficial for maintaining indoor air quality. The use of direct venting minimizes the loss of heated air, ensuring maximum efficiency and comfort. It also features a versatile installation design that provides flexibility to fit various home layouts.

In terms of aesthetics, the Quadra-Fire QV36A-FB does not disappoint. The fireplace boasts a sleek, contemporary design, available in multiple finishes that easily complement any interior decor. Customers can choose from a variety of logs and ember beds to customize the appearance of the fire, creating a personalized focal point that enhances the ambiance of their living space.

Another significant feature is its advanced ignition system, which ensures reliable and hassle-free starting. The QV36A-FB is equipped with a convenient remote control option that allows users to adjust flame height and heat output with ease, providing exceptional comfort without the need to manually tend to the fire.

This fireplace also incorporates several safety mechanisms, including a flame sensor and a safety shut-off feature, ensuring worry-free operation for families with children or pets. The combination of elegance, efficiency, and state-of-the-art technology makes the Quadra-Fire QV36A-FB a preferred choice for homeowners seeking a premium gas fireplace solution.

In conclusion, the QV36A-FB is more than just a heat source; it is a stylish addition that enhances home aesthetics while delivering reliable warmth. With its impressive features and innovative technologies, it stands out as a dependable choice in the world of gas fireplaces.
Top Page Image Contents