Quadra-Fire QV36A-FB owner manual Assembling DVP-12A Slip Sections

Page 24

A

B

Figure 8.3

Figure 8.4

Note: Make sure that the seams are not aligned to prevent unintentional disconnection.

Assembling DVP-12A Slip Sections

The outer flue of the slip section should slide over the outer flue of the pipe section and into (inner flue) the last pipe section (see Figure 8.7) .

Slide together to the desired length, making sure that a 1-1/2 inch outer flue overlap is maintained between the pipe section and slip section.

The pipe and slip section need to be secured by driving two screws through the overlapping portions of the outer flues using the pilot holes (see Figure 8.8).

This will secure the slip section to the desired length and prevent it from separating. The slip section can then be attached to the next pipe section.

If the slip section is too long, the inner and outer flues of the slip section can be cut to the desired length.

Cut from this end

(outer)

CORRECT

Figure 8.5 Seams

INCORRECT

Assembling Minimum Installations (MI) Sections

(inner)

Figure 8.6

Cut from this end

Pilot hole

MI sections are non-unitized so that they can be cut to a certain length. Cut these sections to length from the non- expanded end (see Figure 8.6).

They can then be attached by first connecting the expanded end of the MI inner flue with the inner pipe from the adjacent pipe section and securing with three screws. The expanded portion of the MI inner flue must overlap completely with the unexpanded end of the adjacent pipe section.

The outer flue can then be inserted into the adjacent outer flue expanded end and attached to the next pipe section with three screws. The other end of the MI pipe section can then be attached by fitting another pipe section to it and snapping it together, as normal.

Figure 8.7 Slip Section Pilot Holes

Figure 8.8 Screws into Slip Section

24

Quadra-Fire • Expression 36 (QV36A-FB) • 2062-900 Rev. S • 11/11

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model Expression 36 QV36A-FB What to do if you smell gasHot glass will cause burns Congratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of MassachusettsDesign and Installation Considerations Getting StartedTools and Supplies Needed Inspect Appliance and ComponentsInspect Firebox Framing and Clearances Selecting Appliance LocationModel 41-1/2 17-1/4 45-1/4 QV36A-FBConstructing the Appliance Chase ClearancesMantel Projections Fire Risk Odor RiskClearance to Combustibles 17-1/4 41-1/2 32-1/2254 1321 438 1054 825 914 Termination Locations Vent Termination Minimum ClearancesSee .4 for specific clearances Covered Alcove Applications Vent Information and Diagrams Vent Table KeyMeasuring Standards Use of ElbowsVent Diagrams Top Vent Horizontal Termination One Elbow Two ElbowsMinimum Maximum 2 ftTop Vent Horizontal Termination Three Elbows VT Min HT MaxMust be installed prior to attaching a 90 elbow Top Vent Vertical Termination Three Elbows Min MaxFeet then the total vent run can be Extended to 40 feetVent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall PenetrationInstalling the Ceiling Firestop Installing Attic ShieldVertical Penetration Framing Removing Non-combustible Facing Mate- rial Assembly  B. Installing the Optional Heat-ZoneGas KitAppliance Preparation Securing and Leveling the Appliance Fire Risk Prevent contact with sagging, loose insulationBacker Installing Non-combustible Facing Material 10 Complete Installation of Non-combustibleInstalling Vent Pipe Assembly of Vent SectionsAttaching Vent to the Firebox Assembly Assembling Pipe SectionsAssembling Minimum Installations MI Sections Assembling DVP-12A Slip SectionsDisassembly of Vent Sections Securing the Vent Sections Vertical SectionsHorizontal Sections Installing Heat Shield and Horizontal Termination Cap Installing the Horizontal Termination CapHeat Shield Requirements for Horizontal Termination Important Notice Heat shields may not be field constructedInstalling Roof Flashing and Vertical Ter- mination Cap Roof Pitch Min. FtFoot minimum in snow regions Assembling and Installing Storm Collar Sharp EdgesGas Information Fuel Conversions Gas ConnectionGas Pressures Pressure Natural Gas PropaneHigh Altitude Installations Recommendation for Wire Electrical InformationOptional Accessories Requirements QWSK-MLT Wall Switch Kit IntroductionInstallation precautions To Replace a Light BulbInstallation instructions Determine location Wiring the wall switchFor units with factory installed rocker switch Operating InstructionsSetting Flame Height/manifold pressure Wall Switch Button OperationTemperature Button SET Set Temperature ButtonJunction Box Installation Junction Box DetailFinishing Facing MaterialFacing Requirements FrontsAppliance Setup Clean the ApplianceAccessories Ember PlacementLog Assembly LOGS-2062 Positioning the LogsLOG #1 SRV2062-701 LOG #2 SRV2062-702LOG #3 SRV2062-703 LOG #4 SRV330-706 LOG #5 SRV330-704LOG #6 SRV340-705 Glass Assembly Removing Glass AssemblyReplacing Glass Assembly Burner Removal Only for ServicingAir Shutter Setting Grilles and TrimOperating Instructions Before Lighting ApplianceLighting Appliance IPI Ignition Final inspection byFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Cause Corrective ActionIntelliFire Ignition System Noise, but spark may not be present at pilot hoodCracked, damaged, or loose. Verify connection from sensor Maintaining and Servicing Appliance Maintenance Tasks Inspect Maintenance TasksAppliance Dimension Diagram Reference MaterialsLocation Inches Millimeters Vent Components Diagrams DVP-AS2Horizontal Termination Cap DVP vent componentsRF6M RF12M Service Parts Log Set AssemblyAt Depot Direct Vent Gas Fireplace#17 Valve Assembly Be ordered from an authorized dealerService Parts List StockedLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Contact Information Do not Discard this Manual

QV36A-FB specifications

The Quadra-Fire QV36A-FB is a remarkable direct vent gas fireplace that combines beauty, efficiency, and innovative technology to create a cozy ambiance in any home. This fireplace is designed for those seeking an aesthetically pleasing yet highly functional heating solution.

One of the standout features of the QV36A-FB is its impressive heating capacity. With the ability to produce up to 34,000 BTUs, it effectively warms spaces of various sizes, making it suitable for both small and large living areas. Its impressive efficiency rating maximizes heat output while minimizing gas consumption, ensuring that homeowners can enjoy warmth without the worry of excessive energy bills.

The QV36A-FB employs a direct venting system, allowing for safe and efficient operation. This system draws air from outside for combustion, which is particularly beneficial for maintaining indoor air quality. The use of direct venting minimizes the loss of heated air, ensuring maximum efficiency and comfort. It also features a versatile installation design that provides flexibility to fit various home layouts.

In terms of aesthetics, the Quadra-Fire QV36A-FB does not disappoint. The fireplace boasts a sleek, contemporary design, available in multiple finishes that easily complement any interior decor. Customers can choose from a variety of logs and ember beds to customize the appearance of the fire, creating a personalized focal point that enhances the ambiance of their living space.

Another significant feature is its advanced ignition system, which ensures reliable and hassle-free starting. The QV36A-FB is equipped with a convenient remote control option that allows users to adjust flame height and heat output with ease, providing exceptional comfort without the need to manually tend to the fire.

This fireplace also incorporates several safety mechanisms, including a flame sensor and a safety shut-off feature, ensuring worry-free operation for families with children or pets. The combination of elegance, efficiency, and state-of-the-art technology makes the Quadra-Fire QV36A-FB a preferred choice for homeowners seeking a premium gas fireplace solution.

In conclusion, the QV36A-FB is more than just a heat source; it is a stylish addition that enhances home aesthetics while delivering reliable warmth. With its impressive features and innovative technologies, it stands out as a dependable choice in the world of gas fireplaces.
Top Page Image Contents