Quadra-Fire QVI35S, QVI30S owner manual Placing, Securing and Leveling the Appliance

Page 12

CUT AND BEND

FLASHING AS NEEDED

TO FIT CHIMNEY

SEALANT

ADHESIVE

Figure 7.2

•Trim chimney top plate to minimize excess overhang or bend over flue tile (see Figure 7.2).

•Place 3/8 inch bead of 300º F silicone on flue tile top.

C.Placing, Securing and Leveling the Appliance

•Install insert (without surround attached) into existing fireplace while pulling collar slide plate forward.

•Install gas line into hole provided on insert side.

•If applicable install remote control wires into insert side (see Section 6, F.).

•Secure collar slide plate to appliance by placing locking handle into position with locking tabs (see Figure 7.1) and secure with #8 screw.

•Level the appliance from side to side and front to back. If necessary, use the leveling legs included with the manual bag to set each corner of the base.

•Position any excess flexible vent pipe back up into chimney without sagging. Twist and push flex vent together to shorten.

•Non-combustible, unfaced fiberglass insulation may be installed between the back of the decorative surround and the face of the existing fireplace surround to which the insert is being installed. This insulation is not required, but can assist in the prevention of infiltration of cold air and odors from the chimney.

•Attach surround. Follow instructions accompanying surround.

•Push insert so that surround becomes tight against face of fireplace.

WARNING

Fire Risk.

Only an approved Hearth & Home Technologies surround may be used to cover integral grills on solid fuel burning fireplaces.

• No other components such as shrouds, sheet- metal plates, etc., may be used to seal off vents.

WARNING

Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

WARNING

Explosion Risk.

Combustion Fume Risk.

•Connect vent sections per installation instructions.

•Connect exhaust vent pipe ONLY to exhaust starting collar and termination cap center collar.

•Connect inlet air vent ONLY to inlet air collar on appliance and either the termination cap inlet air collar OR terminate within chimney.

•Do NOT allow vent to sag below connection point to appliance.

12

Quadra-Fire • QVI30S, QVI35S • 340-901 Rev. i • 6/09

 

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Models What to do if you smell gasHOT Surfaces Homeowner Reference Information XxxxxxxxTable of Contents Listing and Code Approvals Design and Installation Considerations Getting StartedTools and Supplies Needed Inspect Appliance and ComponentsFireplace Size Requirements Minimum Fireplace OpeningMinimum Appliance Size Location Clearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesVent Information and Diagrams Vent Table KeyHorizontal Venting Measuring StandardsInstallation Preparation Installing Vent Pipe and Appliance Connecting Vent PipeVenting Components Placing, Securing and Leveling the Appliance Installing Adaptor and Termination Cap Factory Built Wood BurningDamper Flashing Kit Optional Class a PipeGas Information Fuel Conversions Gas ConnectionGas Pressures High Altitude Installations Check for GAS LeaksWiring the Appliance ON/OFF SwitchElectrical Information Appliance RequirementsJunction Box Installation Optional AccessoriesFAN Junction BOX Finishing Mantel ProjectionsAppliance Setup Clean the ApplianceAccessories Ember PlacementRefractory Placement Models Supreme-XT, Grand-XTQVI30, QVI35, ADI60 Refractory from the packagingLog Set Assembly LOGS-QVI30 Positioning the LogsQuadra-Fire QVI30S, QVI35S 340-901 Rev. i 6/09 Quadra-Fire QVI30S, QVI35S 340-901 Rev. i 6/09 Log Set Assembly LOGS-QVI35 Quadra-Fire QVI30S, QVI35S 340-901 Rev. i 6/09 Glass Assembly Air Shutter SettingRemoving Glass Assembly Replacing Glass AssemblyOperating Instructions Before Lighting ApplianceBefore operating this appliance have a qualified technician Lighting Appliance Standing Pilot IgnitionWhat to do if YOU Smell GAS Initial Break-in Procedure Check Pilot Flame AppearanceAfter Appliance is Lit Frequently Asked Questions Issue SolutionsTroubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsAppliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsService Parts Part number list on followingService Parts At DepotLog Set Assembly QVI35SNGKS-QVI35 Standing Pilot Valve Assembly QVI30S, QVI35SLimited Lifetime Warranty Quadra-Fire QVI30S, QVI35S 340-901 Rev. i 6/09 Contact Information

QVI35S, QVI30S specifications

The Quadra-Fire QVI35S and QVI30S are two impressive gas stoves that exemplify modern heating technology while prioritizing efficiency and aesthetics. As part of Quadra-Fire's renowned lineup, both models provide homeowners with outstanding performance and quality design.

One of the primary features of the QVI35S and QVI30S is their high efficiency rating. These stoves boast an impressive efficiency of up to 85%, which means that the majority of the fuel used is converted into heat for your home. This not only translates to lower energy bills but also less frequent fuel replenishment, making them cost-effective and environmentally friendly choices for heating.

Both models feature Quadra-Fire’s innovative heat management system, which ensures even heat distribution throughout the room. This system allows for efficient use of the fire's energy, maximizing warmth and minimizing heat loss. The QVI35S is particularly suited for larger spaces, capable of heating areas up to 1,800 square feet, while the QVI30S is ideal for medium-sized rooms, heating areas of up to 1,500 square feet.

The aesthetics of the QVI35S and QVI30S cannot be overlooked. Both models come with a variety of customizable options including black, pewter, or gold finishes, allowing homeowners to match their stove with their interior decor. The large viewing window enhances the visual appeal, offering a stunning display of the flame and creating a cozy ambiance in any room.

In terms of performance, both models feature the advanced Direct Vent technology. This system ensures that combustion air is drawn from outside the home, which helps maintain excellent indoor air quality. Additionally, the balanced flue design directs exhaust gases safely outside, minimizing emissions.

The stoves also incorporate an easy-to-use control system. Users can quickly adjust the flame height and heat output, allowing for precise temperature control. This feature, combined with the built-in fan option, ensures that heat is circulated effectively, providing optimal comfort.

Easy maintenance is another advantage of the QVI35S and QVI30S. They are designed for simple cleaning, with removable components and an accessible ash pan. This user-friendly design ensures that maintaining your stove is hassle-free.

In conclusion, the Quadra-Fire QVI35S and QVI30S deliver a blend of efficiency, aesthetic appeal, and advanced technology. They provide reliable heating solutions, customizable designs, and user-friendly features, making them excellent additions to any home looking to stay warm and stylish.
Top Page Image Contents