Quadra-Fire QVI35S, QVI30S owner manual Reference Materials, Appliance Dimension Diagram

Page 36

15 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.

N

K

L

A

B

C

M

J

O

GAS INLET

P

Q

R

S

D

E

I

F

GH

ELECTRICAL

ACCESS

T

U

MODEL DIMENSIONS

	LOCATION	QVI35S		QVI30S

		Inches	Millimeters	Inches	Millimeters
		Inches	Millimeters	Inches	Millimeters

	A	33-1/32	839	29-1/32	737
	B	24-1/4	616	20-5/32	512
	C	12-1/8	308	10-3/32	256
	D	36-7/8	937	32-5/16	821
	E	32	813	27-25/32	706
	F	14-3/4	375	12-7/16	316
	G	27	686	22-23/32	577
	H	22-3/4	578	20-1/4	514
	I	23-11/16	602	21-5/32	537
	J	8-7/16 REF	215	8-7/16 REF	215

MODEL DIMENSIONS

LOCATION	QVI35S			QVI30S

	Inches	Millimeters	Inches		Millimeters
	Inches	Millimeters	Inches		Millimeters

K	2-5/16	58	2-5/16		58
L	4-7/16	112	4-7/16		112
M	5-5/32	131	5-5/32		131
N	2-5/32	55	2-5/32		55
O	13-23/32	348	13-23/32		348
P	2-17/32	64	2-17/32		64
Q	5-9/32	135	5-9/32		135
R	8-29/32	227	8-29/32		227
S	14-11/16	373	14-11/16		373
T	2-19/32	66	2-19/32		66

U	6-1/16	154	6-1/16		154

Figure 15.1 Appliance Dimensions

36	Quadra-Fire • QVI30S, QVI35S • 340-901 Rev. i • 6/09

Image 36

Contents Models What to do if you smell gasHOT Surfaces Homeowner Reference Information XxxxxxxxTable of Contents Listing and Code Approvals Design and Installation Considerations Getting StartedTools and Supplies Needed Inspect Appliance and ComponentsFireplace Size Requirements Minimum Fireplace OpeningMinimum Appliance Size Location Clearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesVent Information and Diagrams Vent Table KeyHorizontal Venting Measuring StandardsInstallation Preparation Installing Vent Pipe and Appliance Connecting Vent PipeVenting Components Placing, Securing and Leveling the Appliance Installing Adaptor and Termination Cap Factory Built Wood BurningDamper Flashing Kit Optional Class a PipeGas Information Fuel Conversions Gas ConnectionGas Pressures High Altitude Installations Check for GAS LeaksWiring the Appliance ON/OFF SwitchElectrical Information Appliance RequirementsJunction Box Installation Optional AccessoriesFAN Junction BOX Finishing Mantel ProjectionsAppliance Setup Clean the ApplianceAccessories Ember PlacementRefractory Placement Models Supreme-XT, Grand-XTQVI30, QVI35, ADI60 Refractory from the packagingLog Set Assembly LOGS-QVI30 Positioning the LogsQuadra-Fire QVI30S, QVI35S 340-901 Rev. i 6/09 Quadra-Fire QVI30S, QVI35S 340-901 Rev. i 6/09 Log Set Assembly LOGS-QVI35 Quadra-Fire QVI30S, QVI35S 340-901 Rev. i 6/09 Glass Assembly Air Shutter SettingRemoving Glass Assembly Replacing Glass AssemblyOperating Instructions Before Lighting ApplianceBefore operating this appliance have a qualified technician Lighting Appliance Standing Pilot IgnitionWhat to do if YOU Smell GAS Initial Break-in Procedure Check Pilot Flame AppearanceAfter Appliance is Lit Frequently Asked Questions Issue SolutionsTroubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsAppliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsService Parts Part number list on followingService Parts At DepotLog Set Assembly QVI35SNGKS-QVI35 Standing Pilot Valve Assembly QVI30S, QVI35SLimited Lifetime Warranty Quadra-Fire QVI30S, QVI35S 340-901 Rev. i 6/09 Contact Information