Napco Security Technologies WI1501A Easy Exit, Enable CP-01 Limits, Enable TCP/IP Communications

Page 24

Glossary

Page 24

WI1501A 9/06

E19 - Lug E19 is the Listen in Lug. It is an input and when it is forced low the panel will silence the keypad/Touchpad sounder and bell outputs so that the Veri-phone can listen to activity at the residence. See Veri-Phone (WI783): Silence All Outputs During Audio Session. Use Napco Part number "WL1" for field wiring.

Easy Exit

While armed in the Interior Mode, Easy Exit can be initiated by pressing STAY. Easy Exit restarts the Exit delay, allowing a User to exit an armed premises without disarming and rearming the system.

Easy Menu-Driven Program Mode See Dealer Program Mode

Easy Programming of Auto download ID #'s and PC Preset Callback #

It is now possible to set the PC Preset Auto download ID # and PC Preset Callback phone number from the F-64PROG programmer Easy Menu Driven Program Mode.

1.Enter the Easy Menu Driven Program Mode and press PRIOR/NO until Central Phone # is displayed.

2.Program an "F" followed by the Auto Download ID # (2 digits) and then the Callback Telco # (up to 13 digits).

3.Press Uto save.

4.Exit Program Mode (press RESET, RESET).

5.Remove the F-64PROG Programmer and install a Freedom F-64TP Touchpad (the connector used to wire the F-64PROG to the system buss can also be used with the F-64TP Touchpad).

6.Insert the Master I-FOB into the face of the Touchpad and enter Touchpad Menu Mode by pressing MENU.

7.Go to Function "ACTIVATE DOWNLOAD Y/N" and press YES.

8.The panel will automatically call the PCPreset computer and download the program on the specified Auto DL line #.

Note: After the auto download of the control panel program, the system must be fully tested.

See following example:

Example: Program an Auto Download ID # of 07 and a PC Preset Callback # of 1-516-842-9400.

• Go to Central Phone # input screen and press: [*] [5]

[0] [7]

[1] [5] [1] [6] [8] [4] [2] [9] [4] [0] [0]

[ON/OFF]

("F")

(Auto DL ID#)

(Callback Phone #)

(Save)

Enable Alarm Output on Telco Fail only when Area(s) Armed (Alarm Output Only when Armed)

Allow Telephone Line Fault test to produce an Alarm Output only when armed. Note: Requires "System Features: Alarm Output", "Telco Fail" and version 9 or later panel.

Enable CP-01 Egress Tones Only: Enable this feature if you want exit and entry sounds only--without setting any other CP-01 fea- tures. When enabled, the Exit Delay keypad sounder (including the Exit Urgency sound during the final 10 seconds of the Exit Delay) is enabled.

Enable CP-01 Limits

When enabled, three time limits are enabled as per the SIA CP-01 standards: (1) Exit Delay Time: If an attempt is made to change the Exit Delay time to less than 45 seconds the time will be entered as 60 seconds. The maximum programmable time is 255 seconds; (2) Entry Delay: If an attempt is made to change the Entry Delay time to less than 30 seconds the time will be entered as 30 seconds. The maximum programmable time is 255 seconds; and (3) Abort Delay: If an attempt is made to change the Abort Delay to less than 15 sec- onds or more than 45 seconds the time will be entered as 30 seconds.

Note: In accordance with UL standards, the aggregate of the Entry Delay time and Abort Delay time "window" will not be programmed to

exceed one minute. Note: When "Enable CP-01 Limits" is enabled, the Exit Delay keypad sounder (including the Exit Urgency sound

during the final 10 seconds of the Exit Delay) is enabled only when keypads are used. Note: If "Enable CP-01 Limits" is enabled in EZ Programming, any Zone in a Group will only activate an alarm and send a report ONCE. After the Zone has reported, it will remain in the Group and may still initiate the Zone ANDing sequence.

Enable Keypad 1 Only Programming: In version 01 of the F-64 panel, programming is allowed from any keypad by default. Program to restrict programming to Keypad #1 only, if needed.

Enable Local Alarm on First Zone "AND" Trip See Zone ANDing (Do not program in UL installations)

Enable TCP/IP Communications

Using the NetLink NL-MOD-UL TCP/IP communications module accessory, the F-64 panel can report alarms via contact closures or via its bell output but cannot report alarm data such as point ID information. The F-64 panel can, when the NL-MOD-UL is visible on a net- work, receive Windows Quickloader programming information or transmit panel log information over a network. Refer to the NL-MOD- UL Installation Instructions WI1523 for more information.

Freedom F-64 Installation Instructions

L NAPCO Security Systems

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Freedom F NapcoImportant Notice Table of Contents Introduction Page WI1501A 9/06Specifications WI1501A 9/06 5 Ordering Information System ComponentsSummary of UL Requirements WI1501A 9/06 7 Wheelock AH-12WP Installation Control PanelWiring WI1501A 9/06 9 Testing the System Restore the wireless point close the loopWiring Connections SIREN/BELL PowerAuxiliary Power TransformerRemote BUS Earth GroundBasic Zone Configuration EZ Zone Doublingtm ConfigurationWire Smoke Detectors Wire Smoke Detector WiringTelephone Lines WI1501A 9/06 15 Keypad / Touchpad Messages Keypad / Touchpad MessagesAC Failure AC-Fail Report Delay GlossaryWI1501A 9/06 17  Alarm Outputs Ambush Touchpad Ambush Ambush Codes Enable Global AmbushAreas Zone Area 1-Zone Area 4 Priority Area Arming Auto Status Disable Backup Report on Telco 1/TelcoBattery WI1501A 9/06 19 Chime Zone Chirp Output on Keyfob Arm/DisarmCold Start WI1501A 9/06 21  Data FormatDate/Time Dial-Tone Detection Disable Auto Dial-Tone Detection Digital Dialer Report Enter/Exit Test ModeDealer Security Code Digital Dialer TestWI1501A 9/06 23  Enable CP-01 Limits Enable TCP/IP CommunicationsEasy Exit WI1501A 9/06 25  Keyfob Arm/Disarm chirp of Alarm Output Fire Verification Not for use in CaliforniaGEM-Print Keyfob Control of Relay Groups 1WI1501A 9/06 27  Page 28WI1501A 9/06 WI1501A 9/06 29  Page 30WI1501A 9/06 Sound Alarm On Exit Error Suppress Bypass Icon When ArmedWI1501A 9/06 31  Subscriber ID Numbers Account NumberWire, 4-Wire Smoke Detectors See Smoke Detectors Hour Zone Test Timer Cancel Next Test Timer Report on Any ReportTimeout WI1501A 9/06 33  Trouble on Open Trouble on Short Not for UL installations Trouble Fire TroubleZone Directory Zone Area 1-4 See AreasWI1501A 9/06 35  Zone StatusSTANDBY-BATTERY Calculation Worksheet Alarm current drawn in alarmStandby Time in Hours Box Standby Time1 Wiring Legend WI1501A 9/06 37 Programming Address LocationWI1501A 9/06 39  Factory Default Description Out of Box Panel OperationWI1501A 9/06 41  Out of Box Panel Operation Prior to CP-01 ChangesFCC Statement Freedom F-64 Wiring Diagram WI1501A 9/06 43 Napco Limited Warranty

WI1501A specifications

Napco Security Technologies has long been a trusted name in the security industry, and their WI1501A model is no exception. This advanced wireless intrusion detection and communication solution is engineered to offer exceptional performance, reliability, and versatility, making it a popular choice for both residential and commercial applications.

One of the standout features of the Napco WI1501A is its innovative wireless technology. The unit operates on a robust 433 MHz frequency, ensuring a stable connection with minimal interference from other devices. This frequency allows the WI1501A to cover a significant range, providing flexibility in installation without the constraint of wired connections. Its wireless capability simplifies the installation process, allowing for quick setup and repositioning if necessary.

The WI1501A is equipped with advanced motion detection technology. It utilizes passive infrared (PIR) sensors to accurately detect movement within its monitored area. These sensors are designed to minimize false alarms, ensuring that users are only alerted when genuine activity is identified. This feature is particularly valuable in environments with pets or fluctuating temperature conditions, as the sensors can distinguish between legitimate threats and non-threatening movements.

Another essential aspect of the WI1501A is its integration capabilities. It seamlessly integrates with Napco's central monitoring systems and can be customized to work with various other security components. This interoperability allows users to expand their security systems without worrying about compatibility issues.

Durability is also a key characteristic of the Napco WI1501A. Designed to withstand different environmental conditions, the unit is suitable for both indoor and outdoor installations. Its robust housing protects it from dust and moisture, ensuring long-lasting performance even in challenging settings.

The WI1501A boasts a user-friendly interface and is compatible with smartphone applications, enabling users to monitor their security systems remotely. Customizable settings allow users to tailor the system to their specific needs, whether they require immediate alerts or scheduled monitoring.

In conclusion, Napco Security Technologies' WI1501A is a versatile, reliable, and technologically advanced security solution. With its wireless technology, advanced motion detection, integration capabilities, durability, and user-friendly features, it represents a compelling option for anyone looking to enhance their security measures.
Top Page Image Contents