Napoleon Fireplaces NZ6000 manual Outside Combustion AIR, Mantle Clearances

Page 10

10

OUTSIDE COMBUSTION AIR

Note: Incorporate a vertical loop or trap into air liners to reduce air flow when unit is not in use.

Insulating the in- take liners is recommended

in colder

climates to pre- vent condensa-

tion from occuring.

The Napoleon

Model NZ6000 takes outside air directly into the fireplace

through the openings in the left and right hand sides.

Decide on the most convenient lo- cation for the fresh air inlet ducts and hoods which may be installed above or below floor level.

The fresh air inlet ducts and hoods must be installed.

Secure and seal the intake liners to the collars using 3 sheet metal screws, and high temperature sealant.

Vertical

Horizontal

rise is

run may be:

between:

 

6' & 10' max

5'

3' & 6'

15'

1' & 3'

20'

0' & 1'

25'

Included with the fireplace are:

- two 10' lengths of vent. Use a connector and seal if add- ing more length.

- two of intake hoods.

The vertical height of the air intake liner must not be greater than 2/3 the height of the chimney. If additional liner length is required, it may be doubled by increasing the size from 6" diameter to 8" diameter. Use a 6" to 8" increaser at the hood and a decreaser at the fireplace. Values in brackets represent 8" diameter intake liners.

The duct terminations must be located so they can not be blocked (i.e. snowdrifts). 4' above grade is recommended.

Make a 6 ½" inch hole to suit in an outside wall of the house. From outside, place the fresh air hood into the hole, open side down. Seal with caulking and secure.

MANTLE CLEARANCES

An optional combustible mantle must be a minimum of 12" above the top of the faceplate and not to extend more than 2" from the surface. See chart below for further information.

W415-0594 / A / 02.15.07

Image 10
Contents W415-0442 / C W415-0594 / a W415-0594 / a Table of Contents Napoleon Wood Fireplace Presidents Lifetime Limited Warranty Introduction General InstructionsElectrical Specifications General Information FeaturesHeating Specifications Packing ListInstallation / Framing HI-EFFICIENCY HeatingLocation and Clearances Ceiling From the base of the unit EnclosureWhen Using a Solid Pack Chimney When Using AN AIR Cooled ChimneyVertical Horizontal Rise is Run may be Between Outside Combustion AIRMantle Clearances Included with the fireplace areHearth Extension See hearth examplesHearth Examples See Note #1 Face PLATE, Upper GRILL, Keystone & Door InstallationSee Note #2 Chimney Installation Adding Chimney Sections Straightup ElbowsOffset Chimney Installation Installing Flashing and Storm CollarConnectionto a Masonry Chimney If the ChimneyAttaching the Handle AIR Contol Knob AIR Cooled Chimney InstallationFinishing Wolf SteelOptional NZ64 Blower KIT Installation For complete instructions, see Blower kitNZ64 Blower Installation Electrical Connection Liner supplied stretches to a maximum of 10’NZ64 Blower Replacement NSK Optional Screen KITStarting a Fire Operating InstructionsOperating Sounds and Smells Draft ControlW415-0594 / a Fuel Loading and Burn Cycle Flash Fires ASH Removal ProceduresRE-LOADING the Fireplace Overnight BurnTips for Burning MaintenanceGlass & Gasket Replacement RUN-AWAY or Chimney FireSelecting Wood Creosoteformation AndremovalFireplace and Accessory Replacement Parts ReplacementsAccessories W415-0594 / a Trouble Shooting Guide Symptom Problem Test SolutionRating Plate

NZ6000 specifications

The Napoleon Fireplaces NZ6000 is a premier choice for homeowners seeking an efficient, stylish, and versatile fireplace solution. This powerful unit seamlessly blends modern technology with classic design, providing exceptional warmth and ambiance in any living space.

One of the standout features of the NZ6000 is its remarkable heating capacity. With an impressive output of up to 55,000 BTUs, it can efficiently heat areas of up to 2,500 square feet, ensuring comfort during even the coldest months. The fireplace’s design allows for a dual air-wash system, promoting a clean burn while maintaining clear views of the mesmerizing flames.

The NZ6000 is built with durability in mind, featuring a robust steel construction. Its heavy-duty build ensures that heat retention and distribution are optimized, providing long-lasting performance. Additionally, the cast iron door adds a touch of elegance while enhancing the unit's efficiency. The door's large viewing area allows for an unobstructed view of the fire, creating a warm, inviting focal point in your home.

Incorporating advanced technology, the Napoleon NZ6000 is equipped with a state-of-the-art combustion system that maximizes efficiency and minimizes emissions. This includes an innovative air supply system that enables precise control over the air intake, allowing users to adjust the burn rate to suit their preferences. This not only enhances the performance of the fireplace but also ensures compliance with modern environmental standards.

Another attractive feature is the customizable design options available for the NZ6000. Consumers can choose from a variety of finishes and faceplates, allowing them to tailor the appearance to complement their home décor. The fireplace can also be paired with an array of decorative media, such as logs, stones, or crystals, giving homeowners the flexibility to create their desired aesthetic.

Safety is paramount with the NZ6000. It comes equipped with an advanced safety shut-off system, ensuring peace of mind during operation. The easy-to-use controls and user-friendly design make it accessible for everyone, from novice users to seasoned fireplace enthusiasts.

In summary, the Napoleon Fireplaces NZ6000 brings an exceptional combination of efficiency, durability, and aesthetic appeal, making it a preferred choice for anyone looking to enhance their home's warmth and ambiance. With its cutting-edge technology, customizable options, and focus on safety, the NZ6000 stands out as a top-tier investment for any modern living space.