Chimney Installation

5Place brass washers onto

the faceplate hinge bushing (2 extra washers are sup- plied in order to level the doors if needed).

Install the air c o n t r o l threaded rod and knob.

Slide the door hinge pin into the faceplate hinge bushing.

To remove the doors, open them slightly and lift them out of the faceplate hinge bushings.

Araised hearth together with the fireplace built on a raised platform is recommended for easier wood loading and fire viewing.

The diameter of the chimney is 8".

A chimney venting the fireplace shall not vent any other appliance.

The minimum overall chimney height from the top of the fireplace is 15 feet.

The maximum overall chimney height from the top of the fireplace is 34 feet.

Factory-built chimney systems for use in dwellings constructed for three or more families must be enclosed above the room in which the fireplace is located. This enclosure must have a fire resistance rating equal to or greater than that of the floor or roof assembly through which they pass.

If the chimney system is enclosed within the attic area, a rafter radiation shield is required.

The chimney should not be built with an offset angle in excess of 45° in Canada and 30° in USA.

The chimney must extend at least 3 feet above its point of contact with the roof and at least 2 feet higher than any wall, roof or building within 10 feet.

If the chimney extends more than 5 feet above the roof, it must be secured using a roof brace or guide wires.

Ensure that minimum clearances are maintained.

Portions of the chimney that extend through accessible spaces must always be encased to avoid personal contact with the chimney and thereby avoid damage to the chimney.

A raincap must be installed to avoid internal damage and corrosion.

The chimney must be supported at a maximum of 20 foot intervals (approx. 200 lbs/20 ft).

This fireplace was tested to CAN /ULC S610 Standard for Factory Built Fireplaces, and to UL 127 Factory Built Fireplaces. This Factory Built Fireplace is certified to burn Fire Wood. The Factory Built Fireplace model: NZ6000 has met test criteria for Zero Clearance Installation to Combustible Surfaces.

Any 8" diameter chimney listed to these standards may be installed. In accordance with these standards, the unit may also be connected to any chimney listed to CAN/ULC-S604 and CAN/ULC-S629 for Canada or UL-103HT for the United States.

Installation of all types of factory-built chimney systems is to be in accordance with the chimney manufacturers in- stallation instructions. An appropriate chimney manufac- turers anchor base plate and anchor base plate gasket is required in order to initiate their system. Use the high tem- perature gasket, supplied, to seal between the anchor plate and the fireplace top. Air cooled chimney systems are not recommended in colder climates.

W415-0594 / A / 02.15.07

NZ6000 specifications

The Napoleon Fireplaces NZ6000 is a premier choice for homeowners seeking an efficient, stylish, and versatile fireplace solution. This powerful unit seamlessly blends modern technology with classic design, providing exceptional warmth and ambiance in any living space.

One of the standout features of the NZ6000 is its remarkable heating capacity. With an impressive output of up to 55,000 BTUs, it can efficiently heat areas of up to 2,500 square feet, ensuring comfort during even the coldest months. The fireplace’s design allows for a dual air-wash system, promoting a clean burn while maintaining clear views of the mesmerizing flames.

The NZ6000 is built with durability in mind, featuring a robust steel construction. Its heavy-duty build ensures that heat retention and distribution are optimized, providing long-lasting performance. Additionally, the cast iron door adds a touch of elegance while enhancing the unit's efficiency. The door's large viewing area allows for an unobstructed view of the fire, creating a warm, inviting focal point in your home.

Incorporating advanced technology, the Napoleon NZ6000 is equipped with a state-of-the-art combustion system that maximizes efficiency and minimizes emissions. This includes an innovative air supply system that enables precise control over the air intake, allowing users to adjust the burn rate to suit their preferences. This not only enhances the performance of the fireplace but also ensures compliance with modern environmental standards.

Another attractive feature is the customizable design options available for the NZ6000. Consumers can choose from a variety of finishes and faceplates, allowing them to tailor the appearance to complement their home décor. The fireplace can also be paired with an array of decorative media, such as logs, stones, or crystals, giving homeowners the flexibility to create their desired aesthetic.

Safety is paramount with the NZ6000. It comes equipped with an advanced safety shut-off system, ensuring peace of mind during operation. The easy-to-use controls and user-friendly design make it accessible for everyone, from novice users to seasoned fireplace enthusiasts.

In summary, the Napoleon Fireplaces NZ6000 brings an exceptional combination of efficiency, durability, and aesthetic appeal, making it a preferred choice for anyone looking to enhance their home's warmth and ambiance. With its cutting-edge technology, customizable options, and focus on safety, the NZ6000 stands out as a top-tier investment for any modern living space.