Napoleon Fireplaces BGD40-N, BGD40-P manual Finishing, Optional Wall Switch Installation

Page 22

22

OPTIONAL WALL SWITCH INSTALLATION

For ease of accessibility, an optional remote wall switch may be installed in a

WIRE SIZE

convenient location. A 20ft length of millivolt wire is connected to the gas valve

14 Gauge

and wall switch. However, if a greater length is required route 2-strand (solid

16 Gauge

core) millivolt wire through the electrical hole located at the bottom left side of

the unit. The recommended maximum lead length depends on wire size:

18 Gauge

 

Attach the two leads to terminals 1 and 3 located on the gas valve.

1

Do not connect either the wall switch, thermostat or gas valve directly to 110 volt electricity.

FIGURE 43

3

LENGTH

100Feet

60 Feet

40 Feet

OL

 

N

O

HI

F

O

 

F

 

 

P

 

 

TOLI

TOLIP

FINISHING

MINIMUM MANTEL AND ENCLO-

SURE CLEARANCES

Combustible mantel clearance can vary according to the mantel depth. Use the graph to help evaluate the clearance needed. The three-sided top extension piece may be removed if non-combustible framing is faced with a non-combustible material.

*SEE FIGURE 44.

Dashed lines are suit- able mantel sizes and clearances when a non-combustible fac- ing is used.

When using a non-combustible fi nishing material, the stand- offs may be removed, by removing the set screw in the centre and sliding the stand-offs out of the mounting clips.

FIGURE 45

FIGURE 47

* The top extension may be removed if non-combustible fram- ing is faced with a non-combustible material placed flush with the front face of the unit and extending from the top of the unit. Example: Cement board (not supplied). Combustible counter / bar tops must maintain a minimum of 38" from the base of the fi replace to the underside of the top.

HEAT SHIELD STAND-OFF REMOVAL

 

(SEE THRU INSTALLATION ONLY)

FIGURE 48

END HEAT SHIELD SHOWN

NOTE: Wolf Steel trim and/or surround kits will not totally cover the top extension of the fireplace. In order to obtain a smooth transition from the trim / surround to the wall, it is recommended that the top extension be removed and the unit be installed following the above procedure.

FIGURE 46

W415-0299 / J / 04.14.08

Image 22
Contents $10.00 W415-0299 / J Table of Contents Napoleon GAS Fireplace Presidents Lifetime Limited Warranty General Information IntroductionGeneral Instructions Care of GLASS, and Plated PartsDimensions Venting Lengths VentingSupplier Minimum AIR Terminal Location Clearances Vertical Termination Venting Application FlowchartHorizontal run + verti- cal rise to maximum of 24.75 feet Special Vent Installation Periscope TerminationDefinitions When HT VTHorizontal Termination Elbow Vent Length ValuesFormula 2 HT + VT 24.75 feet Simple venting confi guration only one 45º and 90 elbowVertical Termination = V 1 + V 2 = 1 + 1.5 = 2.5 ft =1 ft=1.5 ft =6 ftVenting Peninsula Installation ProcedureCounter TOP / BAR Installation FramingBrick Panel Installation Facing FinishingOPEN-END Installation Procedure Brick Panel InstallationSEE-THROUGH Installation Procedure Venting FacingMinimum Vent Framing Dimensions Minimum Enclosure DimensionsAdjustable Firestop Installation Wall and Ceiling ProtectionHorizontal Installation Vertical InstallationUsing Flexible Vent Components Elbow SpacersGAS Installation Fireplace Vent ConnectionFinishing Optional Wall Switch InstallationMinimum Mantel and Enclo Sure Clearances LOG Placement Locating Pins #1 Locating PinsLogo Placement Door InstallationL36 Louvre Installation Glowing EmbersEND Door Installation Do not over-tightenOptional Blower Installation Do not overtighten thermodisc or distort housingMaintenance Operation / MaintenanceFireplace Venturi Adjustment AdjustmentsPilot Burner Adjustment Flame CharacteristicsGD420 5 Foot ReplacementsGD430 10 Foot W415-0299 / J Accessories # Part No. DescriptionTrouble Shooting Guide Symptom Problem Test SolutionRefer to Main Burner Goes OUT Pilot Stays on Fireplace Service History W415-0299 / J W415-0299 / J
Related manuals
Manual 36 pages 46.42 Kb

BGD40-P, BGD40-N specifications

Napoleon Fireplaces has long been a name synonymous with quality and innovation in the realm of hearth products. Among its impressive lineup, the BGD40-N and BGD40-P models stand out for their blend of performance, aesthetics, and technology, making them ideal choices for homeowners seeking both efficiency and style.

The BGD40-N is a natural gas fireplace, designed with an emphasis on creating a warm and inviting atmosphere. One of its main features is the glass front that enhances its visual appeal while providing a clear view of the mesmerizing flames. This model is equipped with Napoleon's patented PHAZER log set, which mimics the appearance of real wood, further enriching the realistic ambiance.

In contrast, the BGD40-P is a propane version of the fireplace, offering similar design aesthetics and functionality tailored to propane users. Both models boast a high-efficiency rating, which means they maximize heat output while minimizing gas consumption. This efficiency not only reduces energy costs but also makes them environmentally friendly options for home heating.

One of the standout technologies featured in the BGD40 series is the advanced electronic ignition system. This system ensures that igniting the fireplace is a hassle-free experience, even during power outages when using the optional battery backup. Furthermore, the exclusive Heat Management System provides optimal airflow and distribution of heat, ensuring that living spaces are warmed effectively and consistently.

Safety features are paramount in both models, with a built-in safety shut-off system that enhances peace of mind for users. Additionally, the adjustable flame height allows homeowners to customize their experience, ranging from a gentle glow to a roaring fire.

The design flexibility of the BGD40-N and BGD40-P allows them to fit seamlessly into various home décors, complementing both modern and traditional interiors. With their sleek lines and customizable options, including different media choices, these fireplaces serve as focal points in any room.

Installation is straightforward, with options available for both vented and direct vent configurations. This versatility means they can be installed in various locations, making them suited for new builds or retrofitting into existing structures.

In summary, Napoleon Fireplaces' BGD40-N and BGD40-P models deliver on aesthetics, efficiency, and innovative technology. With their realistic flame effects, user-friendly features, and commitment to safety, they are excellent choices for those seeking to enhance the comfort and ambiance of their homes.