Vermont Casting 1610 installation instructions Defiant NC Clearance Chart for 6 Connections only

Page 14

Defiant 1610 Non-Catalytic Woodburning Stove

Defiant NC Clearance Chart for 6” Connections ONLY

 

 

 

 

 

 

Stove Clearance

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Unprotected Surfaces

 

Protected Surfaces1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Stove Installed

 

Stove

 

Stove Installed

Stove

 

 

 

 

in

 

in

 

 

 

Parallel to Wall

 

 

Parallel to Wall

 

 

 

 

Corner

 

Corner

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Side

Rear

 

Corners

 

Side

 

Rear3

Corners

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Top exit with no

(A) 26”

(B) 31”

 

(C) 27”

 

(D) 13”

 

(E) 26”

(F) 20”

 

connector heat shields.

 

 

 

 

(660 mm)

(787 mm)

 

(686 mm)

 

(330 mm)

 

(660 mm)

(508 mm)

 

Flue collar shield installed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Top exit with heat shields

(G) 26”

(H) 18”

 

(I) 27”

 

(J) 13”

 

(K) 26”

(L) 20”

 

on connector. Flue collar

 

 

 

 

(660 mm)

(457 mm)

 

(686 mm)

 

(330 mm)

 

(660 mm)

(508 mm)

 

shield installed.2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Top exit double-wall chim-

(M) 26”

(N) 23”

 

(O) 16”

 

(P) 10”

 

(Q) 22”

(R) 17”

 

ney connector*. Flue collar

 

 

 

 

(660 mm)

(584 mm)

 

(706 mm)

 

(254 mm)

 

(559 mm)

(432 mm)

 

shield installed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Rear exit

(S) 24”

(T) 21”

 

N/A

 

(U) 10”

 

(V) 21”

N/A

 

(610 mm)

(533 mm)

 

 

 

(254 mm)

 

(533 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chimney Connector Clearance

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Unprotected Vertical Surfaces

 

Protected Vertical Surfaces

 

 

 

 

 

 

 

 

 

 

 

 

Single-wall connector

 

26¹⁄” (673 mm)

 

 

21¹⁄” (546 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Single-wall connector

 

13¹⁄” (343 mm)

 

 

 

21¹⁄” (546 mm)

 

 

 

 

with shields

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Double-wall chimney

 

18¹⁄” (470 mm)

 

 

 

17¹⁄“ (445 mm)

 

 

 

 

connector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Unprotected Ceiling Surfaces

 

Protected Ceiling Surfaces

 

Single-wall connector

 

15” (381 mm)

 

 

 

Not measured

 

 

 

 

(Horizontal)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Clearance to Combustibles in Front of Stove

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

All Installations

48” (1219 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A minimum ceiling height of 8 feet (2.4 m) measured from the base of the stove is required for all installations.

* Using a listed double wall oval to 6” round connector.

1.When wall protection is used, a ceiling heat shield, 24” (610 mm) in diameter and suspended 1” (25 mm) from the ceiling must surround the pipe in installations where the chimney penetrates the ceiling.

2.The connector pipe heat shield must extend 36” (914 mm) above the flue collar. When this shield is used, a single wall pipe may continue vertically unshielded.

3.With protected wall surfaces, the rear clearance must be increased by 3” (76 mm) if the flue collar heat shield is not used. The flue collar shield is required when using connector pipe shields and always with unprotected surfaces.

14

30002850

Image 14
Contents Defiant Welcome Save These Instructions for Future ReferenceStory of the Defiant Table of ContentsInstallation Accessories Specifications Defiant, ModelChimney Height InstallationOutside Air Prefabricated Chimneys What Kind of Chimney to UseMasonry Chimneys Chimney SizeSecuring the Single-wall Connector to a Masonry Chimney Chimney Connector GuidelinesSingle-wall Chimney Connectors Freestanding InstallationsFireplace Installations Above the FireplaceThrough the Fireplace Wall Pass-ThroughsFloor Protection An approved wall pass-through for CanadaFloor Protection for Fireplace Installation Keep the Stove a Safe Distance From Surrounding MaterialsFireplace and Mantel Trim Shields Safe Ways to Reduce ClearancesWall Shields Fireplace and Mantel Trim Clearances Defiant NC Clearance Chart for 6 Connections only Stove Clearance Unprotected Surfaces Protected Surfaces1Defiant NC Clearance Chart for 8 Connections only Stove Clearance1 Unprotected Surfaces Protected SurfacesDefiant NC Clearance Diagrams Unprotected Surfaces Protected SurfacesRefer to Important 1220 mm Note on This Installations Defiant With Flue Collar Heat Shield Only34³⁄₈ Install Stove Legs AssemblySet Up Your Stove Install the Bottom Heat ShieldReverse the Flue Collar If necessary Install the Optional Ash Door Heat ShieldAdjust the Leg Levellers Attach the Damper HandleDefiant Controls Fan Kit InstallationOperation Single Air Control Regulates Heat Output and Burn TimeDamper Directs Air Flow Within the Stove Two Ways to Add FuelAndirons Help Protect the Glass Use the Air Control Settings that Work Best for YouInfra-Red Reflective Glass Panels For Clear Fire Viewing Burn Only High-Quality WoodStarting and Maintaining a Wood Fire Defiant Control SettingsConditioning Your Stove Refuel While the Embers Are Still Hot Add larger pieces of wood as the fire begins to burnAsh Disposal Indoor/Outdoor Location Draft ManagementSteel Chimney Flue SizingCreosote Draft TestingSingle Venting FuelConclusion Maintenance Tighten the Damper Handle as Needed Adjust the Damper as NeededHow to Adjust the Door Latches Replace the Stove Gaskets as NeededChimney System All Gasketed Construction GasketsMaintenance Schedule Stove Chimney ConnectorDefiant Woodburning Stove Defiant Woodburning Stove Model Shell Enamel Parts Defiant Model Defiant 1610 Non-Catalytic Woodburning Stove Limited Lifetime Warranty CFM Corporation