Vermont Casting 1610 installation instructions Refer to Important 1220 mm Note on This

Page 17

Defiant 1610 Non-Catalytic Woodburning Stove

48"

(1220 mm)

48"

(1220 mm)

Refer to

48" IMPORTANT (1220 mm) Note on This Page

48"

(1220 mm)

ST497

48"

(1220 mm)

48"

(1220 mm)

		Refer to
48"	IMPORTANT
(1220 mm)	Note on This
	Note on This
		Page
		Page

	48"
	(1220 mm)

ST499

Fig. 16 Parallel installation, vertical chimney connector, two wall shields. Reduced clearances for both rear and side walls. Wall shields may meet at corner if desired. Shielding for con- nector is centered behind connector.

Fig. 18 Corner installation, vertical chimney connector, two wall shields. Reduced side clearances. Wall shield MUST meet at corner.

IMPORTANT: when the stove is installed with 8” con- nector pipe, wall shields must extend to within 1” (25

48"

(1220 mm)

48"

(1220 mm)

Refer to

IMPORTANT Note on This Page

48"

(1220 mm)

ST498

mm)of the ceiling (up to 9’ (2.7 m)) due to potentially higher pipe temperatures. With 6” connections, the wall shields only need to extend to a height of 48” (1220

mm)as shown in the grey shaded areas of Figures 16, 17 and 18.

Fig. 17 Parallel installation with rear wall pass-through, two wall shields. Reduced clearances to both rear and side walls. Wall shields may meet at corner if desired. Wall pass-through must comply with codes.

Refer to “Special Installations.”

30002850

17

Image 17

Contents Deﬁant Save These Instructions for Future Reference WelcomeStory of the Deﬁant Table of ContentsInstallation Accessories Deﬁant, Model SpeciﬁcationsChimney Height InstallationOutside Air Masonry Chimneys What Kind of Chimney to UsePrefabricated Chimneys Chimney SizeSingle-wall Chimney Connectors Chimney Connector GuidelinesSecuring the Single-wall Connector to a Masonry Chimney Freestanding InstallationsAbove the Fireplace Fireplace InstallationsWall Pass-Throughs Through the FireplaceAn approved wall pass-through for Canada Floor ProtectionKeep the Stove a Safe Distance From Surrounding Materials Floor Protection for Fireplace InstallationFireplace and Mantel Trim Shields Safe Ways to Reduce ClearancesWall Shields Fireplace and Mantel Trim Clearances Stove Clearance Unprotected Surfaces Protected Surfaces1 Deﬁant NC Clearance Chart for 6 Connections onlyStove Clearance1 Unprotected Surfaces Protected Surfaces Deﬁant NC Clearance Chart for 8 Connections onlyUnprotected Surfaces Protected Surfaces Deﬁant NC Clearance DiagramsRefer to Important 1220 mm Note on This Deﬁant With Flue Collar Heat Shield Only Installations34³⁄₈ Set Up Your Stove AssemblyInstall Stove Legs Install the Bottom Heat ShieldAdjust the Leg Levellers Install the Optional Ash Door Heat ShieldReverse the Flue Collar If necessary Attach the Damper HandleOperation Fan Kit InstallationDeﬁant Controls Single Air Control Regulates Heat Output and Burn TimeTwo Ways to Add Fuel Damper Directs Air Flow Within the StoveInfra-Red Reﬂective Glass Panels For Clear Fire Viewing Use the Air Control Settings that Work Best for YouAndirons Help Protect the Glass Burn Only High-Quality WoodStarting and Maintaining a Wood Fire Deﬁant Control SettingsConditioning Your Stove Add larger pieces of wood as the ﬁre begins to burn Refuel While the Embers Are Still HotAsh Disposal Steel Chimney Draft ManagementIndoor/Outdoor Location Flue SizingSingle Venting Draft TestingCreosote FuelConclusion Maintenance How to Adjust the Door Latches Adjust the Damper as NeededTighten the Damper Handle as Needed Replace the Stove Gaskets as NeededAll Gasketed Construction Gaskets Chimney SystemChimney Connector Maintenance Schedule StoveDeﬁant Woodburning Stove Deﬁant Woodburning Stove Model Shell Enamel Parts Deﬁant Model Defiant 1610 Non-Catalytic Woodburning Stove Limited Lifetime Warranty CFM Corporation