Vanguard Heating VSGF-28PTE, VSGF-28NTE Installing Logs, Installing Front Log #1

Page 16

INSTALLATION

Continued

INSTALLING LOGS

WARNING: Failure to posi- tion the parts in accordance with these diagrams or failure to use only parts speciﬁcally approved with this heater may result in property damage or personal injury.

Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

1.Place front log (#1) on top of the grate. Make sure the notches in the bottom of the log ﬁt over the grate prongs (see Figure 24). Push back of logs ﬂush with metal grate bars.

2.Rest middle log (#2) behind metal posts on grate assembly. Make sure the grooves in the bottom of the log ﬁt over the grate. Bring the log forward next to the metal posts (see Figure 25).

3.Slide the grooves in the back of the rear log (#3) against the rear grate prongs. Make sure the log ﬁts securely over the prongs (see Fig- ure 26). Make sure log is completely vertical and not leaning in toward burner where the ﬂame will touch the log.

4.Install ﬁreplace screen by slipping notches of ﬁreplace screen over screws on front of ﬁreplace (see Figure 27).

Front Log (#1)

Notch

Grate

Prongs

Metal Grate Bars

Figure 24 - Installing Front Log (#1)

Middle Log (#2)

Groove Groove

Metal Post
	Grate
Figure 25 - Installing Middle Log (#2)
Groove	Rear Log (#3)
in Back	Rear Log (#3)
of Log
Grate
Prong
	Groove
	in Back
	of Log

Grate

Prong

Figure 26 - Installing Rear Log (#3)

Screws for

Mounting

Screen

Notches

Figure 27 - Installing Fireplace Screen

16

www.desatech.com

113135-01C

Image 16

Contents What to do if YOU Smell GAS Table of Contents Safety Information Local Codes Product Identification Product FeaturesUnpacking AIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Unusually Tight ConstructionVentilation AIR Ventilation Air From Inside BuildingInstallation Ventilation Air From OutdoorsCheck GAS Type Installing HoodElectrical Hookup Installation Clearances Conventional Fireplace InstallationBUILT-IN Fireplace Installation Height Actual Framing Front Width DepthInstalling GAS Piping to Fireplace LocationInstallation Items Needed External Regulator with Vent Pointing DownConnecting Fireplace to GAS Supply Natural GasChecking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPaThan Psig 3.5 kPaInstalling Logs Installing Front Log #1For Your Safety Read Before Lighting Operating FireplaceLighting Instructions Ignitor Button ControlManual Lighting Procedure To Turn OFF GAS To ApplianceThermostat Control Operation Blower OperationPilot Flame Pattern Inspecting BurnersFront Burner Flame Pattern Burner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceLogs Troubleshooting Observed Problem Possible Cause RemedyMaintenance, Stalling Logs, Gas leak. See Warning Statement aboveSpecifications Wiring DiagramService Hints Replacement PartsLOG Base Assembly Models VSGF28NTE and VSGF28PTE Illustrated Parts BreakdownParts List LOG Base AssemblyFireplace Models VSGF28NTE and VSGF28PTE KEY Part Number Description QTY Accessories Perimeter Trim Accessory Hardwood Hearth BaseDuplex Outlet KIT GA3555 Extruded Louver KITKeep this Warranty Warranty InformationLimited Warranty VENT-FREE GAS Fireplace