Vanguard Heating VSGF-28PTE, VSGF-28NTE installation manual Table of Contents

Page 2

WARNING: Improper installation, adjustment, altera- tion, service, or maintenance can cause injury or prop- erty damage. Refer to this manual for correct installation and operational procedures. For assistance or addi- tional information consult a qualified installer, service agency, or the gas supplier.

WARNING: This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provi- sions for adequate combustion and ventilation air must be provided. Refer to Air for Combustion and Ventilation section on page 4 of this manual.

This appliance may be installed in an aftermarket,* per- manently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indi- cated on the rating plate. This appliance is not convert- ible for use with other gases.

*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

State of Massachusetts: The installation must be made by a licensed plumber or gas fitter in the Commonwealth of Massachusetts.

Sellers of unvented propane or natural gas-fired supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for bedroom and bathroom installation in the Common- wealth of Massachusetts.

TABLE OF CONTENTS

Safety Information

3

Troubleshooting

21

Local Codes

4

Wiring Diagram

25

Product Identification

5

Service Hints

25

Unpacking

5

Specifications

25

Product Features

5

Replacement Parts

25

Air For Combustion and Ventilation

6

Technical Service

25

Installation

8

Illustrated Parts Breakdown and Parts List

26

Operating Fireplace

17

Accessories

30

Inspecting Burners

19

Warranty Information

Back Cover

Cleaning and Maintenance

20

 

 

 

2

www.desatech.com

113135-01C

Image 2
Contents What to do if YOU Smell GAS Table of Contents Safety Information Local Codes Unpacking Product FeaturesProduct Identification Determining FRESH-AIR Flow for Heater Location AIR for Combustion VentilationProviding Adequate Ventilation Unusually Tight ConstructionVentilation AIR Ventilation Air From Inside BuildingInstallation Ventilation Air From OutdoorsElectrical Hookup Installing HoodCheck GAS Type Installation Clearances Conventional Fireplace InstallationBUILT-IN Fireplace Installation Height Actual Framing Front Width DepthInstalling GAS Piping to Fireplace LocationInstallation Items Needed External Regulator with Vent Pointing DownConnecting Fireplace to GAS Supply Natural GasThan Checking GAS ConnectionsTest Pressures In Excess Of 1/2 Psig 3.5 kPa Psig 3.5 kPaInstalling Logs Installing Front Log #1Lighting Instructions For Your Safety Read Before LightingOperating Fireplace Ignitor Button ControlThermostat Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Blower OperationFront Burner Flame Pattern Inspecting BurnersPilot Flame Pattern Logs Cleaning MaintenanceBurner Injector Holder and Pilot AIR Inlet Hole Troubleshooting Observed Problem Possible Cause RemedyMaintenance, Stalling Logs, Gas leak. See Warning Statement aboveService Hints SpecificationsWiring Diagram Replacement PartsLOG Base Assembly Models VSGF28NTE and VSGF28PTE Illustrated Parts BreakdownParts List LOG Base AssemblyFireplace Models VSGF28NTE and VSGF28PTE KEY Part Number Description QTY Accessories Duplex Outlet KIT GA3555 Perimeter Trim AccessoryHardwood Hearth Base Extruded Louver KITLimited Warranty VENT-FREE GAS Fireplace Warranty InformationKeep this Warranty