Vanguard Heating VMH10TN installation manual Installing, BUILT-IN Fireplace Installation

Page 12

12

INSTALLING

Continued

BUILT-IN FIREPLACE INSTALLATION

Built-in installation of this fireplace involves installing fireplace into a framed-in enclosure. This makes the front of fireplace flush with wall. An optional brass trim kit accessory is available (see Accessories, page 29). Brass trim will extend past sides of fireplace approximately 1/2 inch. This will cover the rough edges of the wall opening. If installing a built-in mantel above the fireplace, but you must follow the clearances shown in Figure 11, page 13. Follow the instructions below to install the fireplace in this manner. Note: Your Vanguard fireplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against any exterior surface on the rear, sides, or top of your fireplace.

Height

 

Front Width

Depth

Bottom

 

 

 

 

 

 

 

 

Actual

Framing

Actual

Framing

Actual

Framing

Actual

Framing

 

 

 

 

 

 

 

 

 

26"

27

7/8"

26 3/4"

26 7/8"

9 1/2"

10 1/2"

3/4"

3/4"

 

 

 

 

 

 

 

 

 

1.Frame in rough opening. Use dimensions shown in Figure 8 for the rough opening.

10 1/2"

26 7/8"

 

 

3/4" Off

26 7/8"

The Floor

Minimum

 

Figure 8 - Rough Opening for Installing in Wall

If installing in a corner, use dimensions shown in Figure 9 for the rough opening. The height is 26 1/8" which is the same as the wall opening above.

36 5/8"

25 7/8"

26 7/8" 51 3/4"

Figure 9 - Rough Opening for Installing in Corner

2.An optional blower accessory is available (see Accessories, page 29). There are three options for connecting blower to electrical source.

Option one: Install fireplace near an electrical outlet. See Blower Instructions for power cord length.

Option two: Have a licensed electrician install a properly grounded, three-prong 120-volt electrical outlet at fireplace location. Locate outlet inside the framed enclosure. Blower power cord will plug into this outlet. Option three: Have a licensed electrician connect blower to electrical source at junction box inside fireplace.

If using option one, have electrical outlet installed at this time. If using option two, do not connect blower to electrical source at junction box until step 7.

3.Install gas piping to fireplace location. This installation includes an approved flexible gas line (if allowed by local codes) after the manual shutoff valve. The flexible gas line must be the last item installed on the gas piping.

4.If you have not assembled firebox, follow instructions on page 5.

103670

Image 12
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASContents Safety InformationSafety Features Product IdentificationLocal Codes ProductAssembly Installing LogAssembling Fireplace AIR for Combustion VentilationProviding Adequate Ventilation AIR for Determining FRESH-AIR Flow for Fireplace LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIR Tion and ventilation air by one of the methods describedCable local codes Ventilation Air From Inside BuildingAIR for Combustion and Ventilation Ventilation Air From OutdoorsInstallation Installation ItemsCheck GAS Type Locating FireplaceInstallation Installing BUILT-IN Fireplace InstallationMantel Clearances for Built-In Installation Gas Supply,Optional Mantel Installation Attaching Brass Trim to FireplaceAssembling Brass Trim Brass trim shipped with mantel Attaching Wood Base to Solid FloorConnecting To GASSupply Follow all local codesConnecting Fireplace to GAS Supply Installation Items NeededPressure Testing GAS Supply Piping System Pressure Testing Fireplace GAS ConnectionsChecking GAS ConnectionsFireplace Operating Fireplace PilotShutting Off Fireplace Shutting Off Burner Only pilot stays litInspecting Burner Pilot Flame PatternBurner Flame Pattern Correct Burner Flame PatternCleaning and Maintenance Trouble Shooting Observed Possible Problem Cause RemedyODS/PILOT and Burner CabinetSee Cleaning TROUBLE- Shooting Ing statement at TopService ReplacementTechnical HintsAccessories VMH10TN Parts List Model VMH10TNWarranty Information Limited WarrantyVENT-FREE Natural GAS Compact Classic HEARTHâ Fireplace