Vanguard Heating SBVBP(A), SBVBN(A) Optional Remote Operation, Thermostat Control Operation

Page 19

OWNER’S MANUAL

OPERATING

FIREPLACE

Continued

OPTIONAL REMOTE

OPERATION

Note: All remote control accessories must be purchased separately (See Accessories on page 27). Follow instructions included with the remote control.

Thermostat Control Operation

Selector Switch in Remote

Position (GHRC Optional

Remote Control)Control Knob in

On Position

 

LO H

 

ON

 

I

 

 

REMOTE OFF ON

 

T

 

 

L

 

 

 

O

OFF

 

 

I

 

 

P

 

Flame Adjustment Knob

Figure 46 - Setting the (GHRC) Remote Control Selector Switch, Valve Control Knob, and Flame Adjustment Knob for Remote Operation

•In auto mode, the room tempera- ture is controlled by the thermo- stat in the hand-held remote con- trol unit. To increase the room tem- perature, press the top arrow of the TEMP button. To lower the room temperature, press the bottom ar- row of the TEMP button. At higher settings the heater will run more.

IMPORTANT: This remote control has been specially engineered to take an air temperature sample every 5.5 minutes in auto mode. It will not re- spond immediately to the tempera-

(Optional GHRCT Only) The thermostat control setting on the remote control unit can be set to any comfort level between HI and LO. The burners will turn on and off automatically to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of

Selector Switch in

Remote Position

(GHRCT Optional

Remote Control)

ON

OFF

REMOTE

Control Knob in On Position

O

H

 

 

L

 

ON

 

I

 

 

 

 

T

 

 

 

O

OFF

 

 

L

 

 

 

I

 

 

 

P

 

ture setting being turned up or down.

IMPORTANT: The hand-held remote control unit must be near the heater but not extremely close to it. The thermostat on the hand-held remote control unit will heat up too quickly and turn the heater off.

the central heating system, etc.

NOTICE: You must light the pilot before using the hand-held re- mote control unit. See Lighting Instructions, page 18 .

1. After lighting, let pilot flame burn for

about one minute. Turn control knob

on the control valve to ON position.

Turn flame adjustment knob any-

where between HI and LO. Slide the

selector switch to the REMOTE posi-

tion. Note: The burners may light if

hand-held remote ON button was on

when selector switch was last turned

off. You can now turn the burners on

and off with either optional hand-held

remote control unit.

Flame Adjustment Knob

Figure 47 - Setting the (GHRCT) Selector Switch, control Knob, and Flame Adjustment Knob for Remote Operation

GHRC Series Operation:

2a. Press the ON/OFF button to turn the burners on and off. When turning burners off, the pilot will remain lit.

GHRCT Series Operation:

2b. Select the MAN (manual) or AUTO button on the hand-held remote con- trol unit (see Figure 48).

•In manual mode, turn burners on or off by pressing the ON or OFF buttons on the hand-held remote control unit.

3.Use the STATUS button on the hand- held remote control unit to see the operation mode being used and the temperature setting selected. A red light will come on beside the opera- tion mode being used.

4.To turn the burners off when operat- ing in the manual mode, press the OFF button. If operating in the auto mode, press the MAN button, then press the OFF button. The pilot will remain lit. IMPORTANT: To turn the pilot off, manually turn the control knob on the heater to the OFF position.

IMPORTANT: Do not leave the se-

lector switch in the REMOTE posi-

tion when the pilot is not lit. This will

drain the battery.

IMPORTANT: Be sure to press the

ON/OFF buttons on the hand-held

remote control unit for up to 3 sec-

onds to assure proper operation.

Shows Temperature Setting

Allows Burners to be Turned On and Off with the Hand-Held Remote Unit

The Heater will Automatically Cycle Between Pilot and the Heat Setting that has been Selected

HI

TEMP

MAN LO ON

AUTO OFF

STATUS

Increases Room Temperature

Decreases Room Temperature

Turns Burners On and Off

Shows Current Operation Mode

Figure 48 - Hand-Held Thermostat Remote Control Unit Selections

 

(GHRCT Only)

Continued

105500

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents For Your Safety What to do if YOU Smell GAS For Your SafetySBVBNA, Sbvbpa Remote Ready Vent Freestanding Fireplace Safety InformationOperation Product FeaturesProduct Identification Local CodesLocation and Space Requirements PRE-INSTALLATION PreparationUse an adjustable wrench or a 10mm socket Stove Body AssemblyInstalling Fireplace Into Stove Body Freestanding Fireplace AssemblyInstalling GA3700/DA3610T Blowers Installing Optional Blower AccessoryInstalling Rear Cover Venting InstallationInstallation Precautions Type B-VENT Installation Listed B-0 or Greater Installation of Listed B-1 VentRelining Systems Installing Vent System in a ChaseChecking Vent Capacity ChimneysCauses of Spillage and Corrective Action Troubleshooting Venting ProblemsHigh Altitude Installation Flue GAS SpillageCheck GAS Type Fireplace InstallationInstalling GAS Piping to Fireplace Location Installation Items NeededPressure Testing Gas Supply Piping System Connecting Fireplace to GAS SupplyChecking GAS Connections Pressure Testing Fireplace Gas Connections Back View of Thermostat Base Installing Optional Wall Mounted Thermostat GWMT1Installing 9-Volt Battery in Hand- Held Remote Control Unit Installing Remote ReceiverREMOVING/REPLACING Glass Door Installing Log No Installing LOGS, Lava Rock and Glowing EmbersLighting Instructions For Your Safety Read Before LightingManual Lighting Procedure Operating FireplaceGhrct Series Operation Optional Remote OperationThermostat Control Operation Ghrc Series OperationOperating Optional GWMT1 Wall Mounted Thermostat Operating Optional Blower AccessoryPilot Assembly Inspecting BurnersLogs Cleaning and MaintenanceGlass Door Pilot and BurnersAfter pilot lights, keep control knob TroubleshootingPressed in 30 seconds Pane/LP or natural gas company OrificeInlet gas pressure is too low CompanyPilot is partially clogged Fireplace produces unwanted odorsTions on Low line pressureService Hints Replacement PartsTechnical Service Wiring DiagramSbvbna Sbvbpa SpecificationsAccessories Sbvbna Sbvbpa Illustrated Parts BreakdownKEY Part Number Description QTY Parts ListIndicates Color Suffix Designation Amity SCIVF* Series PSCIVF* SeriesKEY Part Description QTY Warranty Information

SBVBN(A), SBVBP(A) specifications

Vanguard Heating SBVBN(A) and SBVBP(A) are advanced heating solutions designed to provide efficient temperature control for residential and commercial applications. Renowned for their innovative features and technologies, these models are engineered to enhance comfort while minimizing energy consumption.

One of the main characteristics of the SBVBN(A) and SBVBP(A) series is their high energy efficiency. Both models utilize advanced heat exchanger technology which allows them to extract maximum heat from the fuel consumed. This efficient heat transfer minimizes waste and leads to lower energy bills for users. The systems typically achieve impressive AFUE (Annual Fuel Utilization Efficiency) ratings, making them an environmentally friendly choice.

Another noteworthy feature of these heating units is their compact, space-saving design. Vanguard has effectively utilized modern engineering principles to produce equipment that can fit into various installation spaces without compromising performance. This is particularly advantageous for urban settings where space is limited.

The SBVBN(A) and SBVBP(A) models incorporate smart technology for enhanced user convenience. Smart thermostats and connectivity options allow users to control their heating systems remotely via smartphone applications. This capability provides greater flexibility and comfort, ensuring that homes and spaces are always at the ideal temperature.

Furthermore, noise reduction technology is integrated into these heating systems, ensuring quiet operation. This is particularly important for residential installations where a peaceful environment is desired. The design minimizes operational noise, allowing users to enjoy a tranquil atmosphere without the disturbance of traditional heating systems.

Safety features are also a prominent aspect of the Vanguard Heating SBVBN(A) and SBVBP(A) models. These include advanced flame sensing technology, automatic shut-off capabilities, and robust construction materials that enhance durability. These features not only ensure reliable performance but also provide peace of mind to users regarding safety concerns.

In terms of maintenance, Vanguard has made these systems user-friendly. They are designed for easy access to components, simplifying routine maintenance tasks and reducing overall service costs. This focus on ease-of-use contributes to the longevity and reliability of the heating systems.

Overall, Vanguard Heating SBVBN(A) and SBVBP(A) models stand out in the market due to their energy efficiency, advanced technologies, compact design, quiet operation, and comprehensive safety features. They embody a commitment to comfort, sustainability, and user satisfaction, making them a worthy choice for anyone in need of reliable heating solutions.
Top Page Image Contents