Vanguard Heating VMH26TPB Optional Mantel Installation, Attaching Brass Trim to Fireplace

Page 14

14

INSTALLING

Continued

OPTIONAL MANTEL INSTALLATION

Note: Refer to instructions provided with the mantel for assembly instructions. Refer to instructions below for system installation. Refer to instructions on page 5 for firebox assembly. Blower accessory should be installed if it is being used (seeAccessories, page32).

1.Unscrew four brass screws that attach top louver to fireplace. Remove louvre from fireplace and set aside.

2.Place fireplace on wood base.

3.Place mantel around fireplace/base assembly.

4.Assemble brass trim kit. See Assembling Brass Trim, page 15.

5.Firmly snap brass trim kit on shoulder screws. Shoulder screws are located on fireplace cabinet (see Figure 12).

6.Align brass trim kit for flush fit around opening.

7.Use two 3" wood screws provided and attach fireplace base to wooden base (see Figure 12).

Shoulder

Screws

Hole for 3" wood screw for attaching fireplace to mantel

 

Hole for 3"

 

wood screw

Assembled

for attaching

fireplace to

Brass Trim

wooden base

Figure 12 - Attaching Brass Trim to Fireplace

8.Remove brass trim kit and mantel. Be careful not to damage wall or mantel.

9.Place wood base next to wall at installation location.

10.Attach wood base to floor with two 1 3/4" black screws provided (see Figure 13). If the floor is concrete use anchor method (see Attaching Wood Base to Solid Floor, page 15).

1 3/4" Screw

Wood

Base

Figure 13 - Attaching Wood Base to Floor

11.Install gas line. See Connecting To Gas Supply, pages 16-18.

12.Check for leaks. See Checking Gas Connections, page 18.

13.Place mantel around fireplace. Be careful not to damage wall or mantel.

14.Place brass trim kit on the shoulder screws located on the side and top of the fireplace. Firmly snap the brass trim over the shoulder screws on fireplace (see Figure 12).

15.Adjust assembly to remove any gaps. Attach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the mantel. The openings are located at top behind the area for the brass louvers (see Figure 13).

16.Reinstall top brass louvers.

102886

Page 13 Page 15
Image 14
Page 13 Page 15
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASContents Safety Information Safety Information Piezo Ignition System Local Codes Product Features UnpackingSafety Pilot Thermostatic Heat ControlAssembly Installing LogUnusually Tight Construction AIR for Combustion and VentilationProviding Adequate Ventilation Confined and Unconfined SpaceDetermining FRESH-AIR Flow for Fireplace Location Determining if You Have a Confined or Unconfined SpaceVentilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Ventilation Air from Outdoors Shown with Optional MantelCheck GAS Type InstallationInstallation Items Locating FireplaceCeiling Installing BUILT-IN Fireplace InstallationMantel Clearances for Built-In Installation Side Firebox Mantel ShelfOptional Mantel Installation Attaching Brass Trim to FireplaceAssembling Brass Trim Brass trim shipped with mantel Attaching Wood Base to Solid FloorConnecting to GAS Supply External Regulator with Vent Pointing DownConnecting Fireplace to GAS Supply Installation Items NeededConnecting to GAS Supply Checking GAS Connections Pressure Testing GAS Supply Piping SystemPressure Testing Fireplace GAS Connections Manual Shutoff ValveOperating Fireplace Pilot Shutting Off Fireplace Shutting Off Burner Only pilot stays litInspecting Burner Pilot Flame PatternBurner Flame Pattern Correct Burner Flame PatternCabinet Cleaning and Maintenance Trouble ShootingODS/PILOT and Burner See Cleaning TROUBLE- ShootingObserved Possible Remedy Problem Cause Ing statement at top Connections,Parts Under Warranty Technical ServiceService Hints Parts Not Under WarrantyVMH26TP Parts List Model VMH26TPGA3400T AccessoriesValve GA5010 Unfinished GM921U Finished GM920F102886 102886 102886 Warranty Information Keep this Warranty
Top Page Image Contents