Vanguard Heating VP2000BTC Placing Heater On Mounting Bracket, Installing Bottom Mounting Screws

Page 13

INSTALLING TO WALL

Continued

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings. IMPORTANT: Do not hammer key!

For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

Figure 10 - Popping Open Anchor Wings For Thin Walls

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Placing Heater On Mounting Bracket

1.Locate two horizontal slots on back panel of heater.

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket.

Stand-Out Tab

Horizontal Slots

Mounting Bracket (attached to wall)

Figure 11 - Mounting Heater Onto Mounting Bracket

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 12).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching To Wall Anchor Method, page 12.

If installing bottom mounting screw into wall stud, drill holes at marked loca- tions using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly secured to wall. Do not over tighten. Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 14-16).

Figure 12 - Installing Bottom Mounting Screws

103876

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information ContentsSafety Product Identification FeaturesLocal Codes UnpackingVentilation AIR for CombustionProviding Adequate Ventilation Determining AIR Flow for Heater Location AIR for Combustion and VentilationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air from Outdoors Ventilation Air From OutdoorsInstallation Items Installing To WallCheck GAS Type Locating Heater Locating Thermostat Sensing Bulb Thermostat Sensing Bulb Attaching Thermostat Sensing Bulb Wall Installing Heater to WallMounting Bracket Removing Front Panel Of HeaterMaintain minimum clearances shown in . If you can Marking Screw LocationsProvide greater clearances from floor and joining wall Attaching Mounting Bracket To WallPlacing Heater On Mounting Bracket Installing Bottom Mounting ScrewsSupply Connecting To GASChecking GAS Pressure Testing GAS Supply Piping SystemConnections Checking Pressure Testing Heater GAS ConnectionsOperating Heater For Your Safety Read Before LightingOperating Heater Shutting Off Heater Manual Lighting ProcedureShutting Off Burner Only pilot stays lit Pilot Flame Pattern Inspecting BurnerCorrect Burner Flame Pattern Burner Flame PatternObserved Possible Problem Cause Remedy Cleaning and Maintenance Trouble ShootingODS/PILOT and Burner CabinetObserved Possible Remedy Problem CauseTROUBLE- Shooting Cleaning and MainteTrouble Shooting Service Hints Technical ServiceVP2000BTC VP2800BTC Parts Under Warranty Service Publications Replacement PartsParts Not Under Warranty VP2000BTC VP2800BTC KEY Part Number for VP2000BTC VP2800BTC Description QTY Parts ListFloor Mounting Stand AccessoriesModel VP2000BTC GA4000B Model VP2800BTC GA4010B Manual Shutoff103876 Limited Warranty VENT-FREE Residential GAS Heaters Warranty Information
Top Page Image Contents