Vanguard Heating VP2000BTC, VP2800BTC AIR for Combustion, Providing Adequate Ventilation

Page 5

AIR FOR

WARNING ICONG 001 WARNING

COMBUSTION

This heater shall not be installed in a confined space unless

AND

provisions are provided for adequate combustion and ventilation

air. Read the following instructions to insure proper fresh air for

VENTILATION

this and other fuel-burning appliances in your home.

 

Today’s homes are built more energy efficient than ever. New materials, increased

 

insulation, and new construction methods help reduce heat loss in homes. Home

 

owners weather strip and caulk around windows and doors to keep the cold air out

 

and the warm air in. During heating months, home owners want their homes as

 

airtight as possible.

 

While it is good to make your home energy efficient, your home needs to breathe.

 

Fresh air must enter your home. All fuel-burning appliances need fresh air for

 

proper combustion and ventilation.

 

Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances draw air from

 

the house to operate. You must provide adequate fresh air for these appliances.

 

This will insure proper venting of vented fuel-burning appliances.

 

PROVIDING ADEQUATE VENTILATION

 

The following is excerpts from National Fuel Gas Code. NFPA 54/ANSI Z223.1,

 

Section 5.3, Air for Combustion and Ventilation.

 

All spaces in homes fall into one of the three following ventilation classifications:

 

1. Unusually Tight Construction; 2. Unconfined Space; 3. Confined Space.

 

The information on pages 5 through 8 will help you classify your space and provide

 

adequate ventilation.

 

Unusually Tight Construction

 

The air that leaks around doors and windows may provide enough fresh air for

 

combustion and ventilation. However, in buildings of unusually tight construction,

 

you must provide additional fresh air.

Unusually tight construction is defined as construction where:

a.walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder with a rating of one perm (6x10-11per pa-sec-m2) or less with openings gasketed or sealed and

b.weather stripping has been added on openable windows and doors and

c.caulking or sealants are applied to areas such as joints around window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at other openings.

If your home meets all of the three criteria above, you must provide addi- tional fresh air. See Ventilation Air From Outdoors, page 8.

If your home does not meet all of the three criteria above, proceed to page 6.

Confined and Unconfined Space

The National Fuel Gas Code (ANSIZ2123.1, 1992 Section 5.3) defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour

(4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space and an unconfining space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed*, through openings not furnished with doors, are consid- ered a part of the unconfined space.

*Adjoining rooms are communicating only if there are doorless passageways or ventilation grills between them.

Continued 5

103876

Page 4 Page 6
Image 5
Page 4 Page 6
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information ContentsSafety Product Identification FeaturesLocal Codes UnpackingProviding Adequate Ventilation AIR for CombustionVentilation Determining if You Have a Confined or Unconfined Space AIR for Combustion and VentilationDetermining AIR Flow for Heater Location Ventilation Air From Inside Building Ventilation AIRVentilation Air from Outdoors Ventilation Air From OutdoorsInstallation Items Installing To WallCheck GAS Type Locating HeaterAttaching Thermostat Sensing Bulb Thermostat Sensing BulbLocating Thermostat Sensing Bulb Wall Installing Heater to WallMounting Bracket Removing Front Panel Of HeaterMaintain minimum clearances shown in . If you can Marking Screw LocationsProvide greater clearances from floor and joining wall Attaching Mounting Bracket To WallPlacing Heater On Mounting Bracket Installing Bottom Mounting ScrewsSupply Connecting To GASConnections Pressure Testing GAS Supply Piping SystemChecking GAS Checking Pressure Testing Heater GAS ConnectionsOperating Heater For Your Safety Read Before LightingOperating Heater Shutting Off Burner Only pilot stays lit Manual Lighting ProcedureShutting Off Heater Pilot Flame Pattern Inspecting BurnerCorrect Burner Flame Pattern Burner Flame PatternObserved Possible Problem Cause Remedy Cleaning and Maintenance Trouble ShootingODS/PILOT and Burner CabinetObserved Possible Remedy Problem CauseTROUBLE- Shooting Cleaning and MainteTrouble Shooting VP2000BTC VP2800BTC Technical ServiceService Hints Parts Not Under Warranty Service Publications Replacement PartsParts Under Warranty VP2000BTC VP2800BTC KEY Part Number for VP2000BTC VP2800BTC Description QTY Parts ListFloor Mounting Stand AccessoriesModel VP2000BTC GA4000B Model VP2800BTC GA4010B Manual Shutoff103876 Limited Warranty VENT-FREE Residential GAS Heaters Warranty Information

VP2800BTC, VP2000BTC specifications

Vanguard Heating has made notable strides in the heating solutions market with its cutting-edge models, the VP2000BTC and VP2800BTC. These units cater to both residential and commercial needs, providing users with efficient heating capabilities under various conditions.

The VP2000BTC is designed with a powerful 2000-watt output, making it suitable for smaller spaces or specific zones within larger environments. It boasts a sleek, modern design that allows for easy integration into any setting, whether it’s a living room, office, or workshop. One of its key features is the advanced thermostat control, which enables precise temperature regulation. This not only enhances user comfort but also contributes to energy efficiency by ensuring that the heating system operates only when necessary.

On the other hand, the VP2800BTC steps up the power to an impressive 2800 watts, making it ideal for larger spaces requiring a more robust heating solution. This model incorporates a multi-functional control panel that allows the user to set timers and customize heating schedules. By doing so, users can optimize their energy consumption, leading to cost savings over time.

Both units utilize infrared heating technology, which offers several advantages over traditional heating methods. Infrared heating warms objects and surfaces directly rather than heating the air, resulting in quicker and more efficient warmth. This technology minimizes heat loss, ensuring that energy is used effectively and providing immediate comfort.

Another noteworthy characteristic of the VP2000BTC and VP2800BTC is their emphasis on safety. Each model comes equipped with overheat protection and a tip-over switch, which provides peace of mind, especially in households with children or pets. Additionally, their lightweight design allows for easy transport and repositioning, making them versatile solutions for various applications.

In summary, the Vanguard Heating VP2000BTC and VP2800BTC are excellent choices for those seeking effective and efficient heating solutions. With their advanced features, precision control, and infrared technology, they stand out as practical options for enhancing comfort in any environment.
Top Page Image Contents