Vanguard Heating VP26A Installing Bottom Mounting Screws, Placing Heater On Mounting Bracket

Page 10

INSTALLATION

Continued

2.Fold wall anchor as shown in Figure 9.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings.

IMPORTANT: Do not hammer key!

For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Figure 9 - Folding Anchor

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 12).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hol- low or solid wall, install wall anchors. Fol- low steps 1 through 4 under Attaching To Wall Anchor Method, pages 9 and 10.

If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly se- cured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 12 and 13).

Figure 10 - Popping Open Anchor Wings

For Thin Walls

Placing Heater On Mounting Bracket

1.Locate two horizontal slots on back panel of heater.

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mount-

ing bracket.

Horizontal Slots

Mounting Bracket (attached to wall)

Stand-Out Tab

Front View

Wall

Heater

Spacer

Side View

Figure 12 - Installing Bottom Mounting

Screws

Figure 11 - Mounting Heater Onto

Mounting Bracket

10

www.desatech.com

113052-01A

Image 10
Contents VN30A, VN30TA, VP16ITA, VP22ITA Model VN30A ShownTable of Contents Safety Information Product Identification Product FeaturesLocal Codes UnpackingProviding Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation AIR Ventilation Air From Inside BuildingCheck GAS Type InstallationInstallation Items Locating HeaterMounting Bracket Installing Heater to WallThermostat Sensing Bulb Removing Front Panel Of HeaterMarking Screw Locations Methods For Attaching Mounting Bracket To WallPlaque Heater Installing Bottom Mounting Screws Placing Heater On Mounting BracketMounting Heater to Floor Connecting to GAS SupplyMounting Base Feet to Floor Where required by local code Mounting Base Feet to HeaterChecking GAS Connections Gas ConnectionPressure Testing Gas Supply Piping System Pressurize supply piping system by eitherOperating Heater NON-THERMOSTAT Models For Your Safety Read Before LightingLighting Instructions To Select Heating Level Manual Lighting ProcedureThermostat Models For Your Safety Read Before Lighting To Turn OFF GAS To ApplianceVP16TA VP26TA Thermostat Operation PlaquePilot Flame Pattern Inspecting HeaterBurner Flame Pattern ODS/PILOT and Burner Cleaning MaintenanceCleaning Burner Pilot AIR Inlet CabinetTroubleshooting Observed Problem Possible Cause RemedyPress in control knob fully Gas leak. See Warning Metal expanding while heating or contracting while coolingSpecifications Illustrated Parts Breakdown Cabinet Body ModelsParts List Cabinet Body Models VP16ITA and VP22ITA KEY Part Number VP16ITA VP22ITA Description Illustrated Parts Breakdown and Parts List Burner Assembly Models VP16A and VN18ABurner Assembly Models VP26A and VN30A ODS/Pilot Burner Assembly VP26A, VN30ABurner Assembly Models VP16ITA and VP22ITA Burner Assembly VP16ITABurner Assembly Models VP16TA, VN18TA, VP26TA, and VN30TA Technical Service Replacement PartsService Publications Service Hints Parts Under WarrantyFAN Kits GA3250T AccessoriesParts Central Equipment Shutoff Valve GA5010113052-01A 113052-01A Keep this Warranty Warranty InformationLimited Warranty Vanguard VENT-FREE Infrared GAS Heaters