Empire Comfort Systems 1, DVD32FP3, 3)(N installation instructions Horizontal Termination

Page 29

HORIZONTAL TERMINATION

NOTE: Termination cap should pass through the wall firestop from the exterior of the building. Adjust the termination cap to its final exterior position on the building.

WARNING: Termination cap must be positioned so that arrow is pointing up.

Attach the termination cap with the four wood screws provided. Before attachment of the termination, run a bead of silicone sealant rated above 250°F on its outside edge too, so as to make a seal to the exterior wall.

NOTE: Wood screws can and should be replaced with appropriate fasteners for use on stucco, brick, concrete or other types of siding.

CAUTION: If exterior walls are finished with vinyl siding (or materials that could become discolored or warp), it is necessary to install a vinyl siding standoff.

The vinyl siding standoff will be installed between the vent terminationandtheexteriorwall.(SeeFigure43)Thishorizontalvent termination bolts onto the flat portion of the vinyl siding standoff, so an air space will exist between the wall and the termination cap.

For installations requiring a vertical rise on the exterior of the building, 14-inch and 36-inch tall Snorkel Terminations, as shown in Figure 44 are available. Follow the same installation procedures as used for standard Horizontal Terminations. If the Snorkel Termination must be installed below grade, (i.e. basement application), proper drainage must be provided to prevent water from entering the Snorkel Termination. Refer to Figure 45. Do not attempt to enclose the Snorkel within the wall or any other type of enclosure.

SNORKEL

12 INCHES MINIMUM

Figure 44

SNORKEL

Figure 43

12 INCHES MINIMUM

ADEQUATE

DRAINAGE

Figure 45

23552-4-0408

Page 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Installation Instructions Table of Contents Important Safety Information LP-GAS Warning Odor Safety Information for Users of LP GASKeep Clear of ALL Obstructions Requirements for MassachusettsIntroduction DVVK-4TSP SpecificationsDVVK-4TP DVVK-4RPDVD32 DVD36 DVD42 DVD48 Fireplace DimensionsDim Clearances Mantel Chart FigureClearance to Combustibles Combustible MaterialLocating Fireplace GAS Supply Installing a New Main Gas CockRecommended Gas Pipe Diameter Checking Manifold PressuresConverting flue take-off to rear venting Rear Vent ConversionSpecial Vent Systems Vent Pipe Clearance InstallationFraming and Finishing Finishing Figures 13 Flush Mount Mantel Installation FigureFraming Figure VERTICAL, 90 Elbow with Horizontal Termination Flush Wall InstallationVERTICAL, 90 Elbow to Horizontal OUT the Wall Horizontal ONLY, Straight OUT the BackDim Venting Fireplace TOP Venting Graph Dimensions in FeetTo Use the Vent Graph Figure Example aVenting Fireplace TOP Below Grade InstallationCutting the Hole Figures Fireplace Hard Elbow Dimensions SeriesFireplace Flex Pipe 90 Degree Bend Series Positioning the FireplaceExamples TOP Vent RUN Venting Fireplace Rear Examples Rear Vent RUN Information on Various Venting Routes and Components Vertical Sidewall InstallationsTermination Clearances Vent Clearances Special Venting Components Simpson Duravent Installing Vent Components FigureVent System Identification Installing Firestops Installing Support Brackets FigureFraming and Finishing Horizontal Firestops FigureSee Horizontal Termination Page 29 and Vertical Termination Vertical Firestops Figures 40, 41Horizontal Termination Parts Verification DVVK-4RE Vent KIT Installation InstructionsInstalling Wall Thimble/Firestop Assembly DVVK-4RE Vent KIT Installation Instructions Connecting to Rigid Vent System Parts ListDVVK-4F Flex Vent Instructions InstallationInstalling the Vent System in a Chase General MaintenanceVertical Termination Determining Minimum Vent Height Above the RoofReassembly and Resealing Vent Pipe System Installation of Vertical Inlet BaffleEmber Material Placement on Burner LOG Placement 5 LOG SETLOG Placement 7 LOG SET Millivolt System Operating InstructionsInitial Lighting Pilot Flame FigureTRW Standing Pilot Wiring Diagram Personal injury or loss of life Standing Pilot Lighting InstructionsFrequent pilot outage problem Standing Pilot TroubleshootingPilot and main burner extinguish while in operation Glass sootsElectric 120 volt Operated Remote Control Frec Direct Ignition Wiring DiagramOptional Remote Control What to do if YOU Smell GAS Direct Ignition Lighting InstructionsInitial Start UP GAS Line Purge Direct Ignition TroubleshootingSymptom Check Action Valve Conversion Direct Ignition PROPANE/LP GAS ConversionMaxitrol Valve Conversion Please Note Maintenance and ServiceParts List Parts View Wiring FBB4 Optional Variable Speed Blower InstallationBlower Motor Blower WheelsVolt AC Optional Brick Liner Installation Instructions Junction BOX Wiring Installation InstructionsAccessory Description Model Number AccessoriesHerringbone Aged BrickMission Arch Leaf Decorative AccessoriesLeaf Rectangle Mission Rectangle Plain Rectangle Leaf Arch Mission Arch Plain ArchService Notes HOW to Order Repair PartsService Notes Service Notes Service Notes Comfort Systems

2, 1, DVD32FP3, 3)(N specifications

Empire Comfort Systems has long been a staple in the heating industry, offering innovative solutions for home heating needs. Among their impressive lineup, the Empire Comfort Systems 3)(N,1,2,DVD32FP3 stand-out model highlights a blend of traditional craftsmanship and modern technology. This fireplace insert is designed to provide warmth and an inviting atmosphere to any living space.

One of the primary features of the DVD32FP3 is its impressive efficiency. The unit is fueled by natural gas, which not only ensures a dependable heat source but also provides relatively lower operational costs. This model boasts a high efficiency rating, allowing homeowners to enjoy significant savings on utility bills while keeping the environment in mind. Its design allows for efficient heat distribution, ensuring that warmth fills the room without excessive energy consumption.

The Empire 3)(N,1,2,DVD32FP3 also emphasizes user convenience with its innovative controls. It features an adjustable thermostat that allows users to set their desired temperature easily, enhancing comfort levels within the home. A remote control option is also available, adding an extra layer of convenience for adjusting the fireplace settings from anywhere in the room.

Aesthetic appeal is another highlight of this model. With its sleek, contemporary design, the DVD32FP3 can blend seamlessly with various home decors. The unit is equipped with a large viewing window, providing a stunning visual of the flames while also giving a cozy ambiance to the space. The realistic log set enhances the appearance, mimicking the beauty of a traditional wood-burning fireplace without the hassle of wood maintenance.

Safety is of paramount importance with the Empire Comfort Systems 3)(N,1,2,DVD32FP3. It comes with a built-in safety sensor which ensures that the unit operates safely, providing peace of mind to homeowners. Additionally, its zero-clearance design allows for installation in various spaces without needing excessive modifications to existing structures.

Durability is a key characteristic of this fireplace insert, crafted from quality materials that promise longevity in performance. This makes it a reliable choice for home heating needs that can withstand the test of time and usage.

Overall, Empire Comfort Systems 3)(N,1,2,DVD32FP3 stands out for its combination of efficiency, aesthetic appeal, user-friendly features, and safety measures, making it an excellent choice for homeowners looking for comfort and reliability in their heating solutions. Whether you're nestled by the fire on a cold winter night or enhancing your living space, it's a perfect choice for warmth and style.
Top Page Image Contents