Empire Comfort Systems 1, DVD32FP3 LOG Placement 5 LOG SET, Ember Material Placement on Burner

Page 36

LOG PLACEMENT (5 LOG SET)

Before you begin: if you are installing logs into the DVD32 or DVD36 model then this fireplace is supplied with a set of five ceramic fiber logs. Do not handle these logs with your bare hands! Always wear gloves to prevent skin irritation from ceramic fibers. After handling logs, wash your hands gently with soap and water to remove any traces of fibers.

The positioning of the logs is critical to the safe and clean operation of this fireplace. Sooting and other problems may result if the logs are not properly and firmly positioned in the fireplace. Please refer to Figure 54 and Figure 55 and corresponding WARNING when completing following log placement instructions.

1.Remove top louver, grasp louver, lift and pull forward.

2.Lower bottom louver, lift and hinge forward.

3.Release two glass frame spring clamps at bottom of firebox.

4.Remove glass frame assembly.

5.Place front logs (#1 and #2) between front grate flange and main burner. Align notches on front logs with locator tabs in base.

6.Place middle log (#3) between front and rear loop of burner. Note: Do not place log on top of pilot assembly.

7.Place rear log (#4) on rear log shelf. Bottom flange of log must be placed between the log shelf and burner tube.

8.Place branch (#5) onto (#1) log and flat area on (#3) log. The bottom of the branch is to be placed behind the grate tang that is second from the left.

9.Place decorative rock in front of grates and sides of main burner pan.

ATTENTION: Do not place decorative rock on logs or burner. The decorative rock should only be placed on the fireplace floor.

EMBER MATERIAL PLACEMENT ON BURNER

10.After all logs are positioned properly, apply Rockwool ember material to the front burner port area. To apply, carefully separate the ember material into small amounts no larger than "dime size" pieces. Fluffed up pieces one layer thick on top of the burner generally works best, and will provide the best ember glow. Do not place ember material more than one layer thick. No more than (1) small packet of ember material (part no. 15999) evenly placed on the burner, is recommended on DVD32 and DVD36 models. Using additional ember material will decrease the amount of ember glow effect. Extra ember material should be saved for future ember applications as necessary. See Figure 55.

11.Replace glass frame onto firebox.

12.Secure the two glass frame spring clamps at bottom of firebox.

13.Align the tabs on top louver brackets with slots in front posts to secure top louver.

14.Close bottom louver. Lift slightly to engage the end tabs into the slots in fireplace sides to close louver panel.

4

5

3

2

1

Figure 54

WARNING: Failure to position the parts in accordance with this diagram or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

Attention: Do not use Figure 54 or Figure 55 to order logs. Refer to parts list on page 49 and parts view on page 50 to order logs and/or ember material for your appropriate fireplace model.

3 5

4

2

1

EMBER MATERIAL

PLACEMENT

Figure 55

Page 36

23552-4-0408

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Installation Instructions Table of Contents Important Safety Information Safety Information for Users of LP GAS LP-GAS Warning OdorRequirements for Massachusetts Keep Clear of ALL ObstructionsIntroduction Specifications DVVK-4TSPDVVK-4TP DVVK-4RPFireplace Dimensions DimDVD32 DVD36 DVD42 DVD48 Mantel Chart Figure ClearancesClearance to Combustibles Combustible MaterialLocating Fireplace Installing a New Main Gas Cock GAS SupplyRecommended Gas Pipe Diameter Checking Manifold PressuresRear Vent Conversion Special Vent SystemsConverting flue take-off to rear venting Installation Framing and FinishingVent Pipe Clearance Flush Mount Mantel Installation Figure Framing FigureFinishing Figures 13 Flush Wall Installation VERTICAL, 90 Elbow with Horizontal TerminationHorizontal ONLY, Straight OUT the Back VERTICAL, 90 Elbow to Horizontal OUT the WallDim Venting Graph Dimensions in Feet Venting Fireplace TOPTo Use the Vent Graph Figure Example aBelow Grade Installation Venting Fireplace TOPFireplace Hard Elbow Dimensions Series Cutting the Hole FiguresFireplace Flex Pipe 90 Degree Bend Series Positioning the FireplaceExamples TOP Vent RUN Venting Fireplace Rear Examples Rear Vent RUN Vertical Sidewall Installations Termination ClearancesInformation on Various Venting Routes and Components Vent Clearances Installing Vent Components Figure Vent System IdentificationSpecial Venting Components Simpson Duravent Installing Support Brackets Figure Installing FirestopsFraming and Finishing Horizontal Firestops FigureVertical Firestops Figures 40, 41 See Horizontal Termination Page 29 and Vertical TerminationHorizontal Termination DVVK-4RE Vent KIT Installation Instructions Installing Wall Thimble/Firestop AssemblyParts Verification DVVK-4RE Vent KIT Installation Instructions Parts List Connecting to Rigid Vent SystemInstallation DVVK-4F Flex Vent InstructionsGeneral Maintenance Installing the Vent System in a ChaseVertical Termination Determining Minimum Vent Height Above the RoofInstallation of Vertical Inlet Baffle Reassembly and Resealing Vent Pipe SystemLOG Placement 5 LOG SET Ember Material Placement on BurnerLOG Placement 7 LOG SET Operating Instructions Millivolt SystemInitial Lighting Pilot Flame FigureTRW Standing Pilot Wiring Diagram Standing Pilot Lighting Instructions Personal injury or loss of lifeStanding Pilot Troubleshooting Frequent pilot outage problemPilot and main burner extinguish while in operation Glass sootsDirect Ignition Wiring Diagram Optional Remote ControlElectric 120 volt Operated Remote Control Frec Direct Ignition Lighting Instructions What to do if YOU Smell GASDirect Ignition Troubleshooting Symptom Check ActionInitial Start UP GAS Line Purge Direct Ignition PROPANE/LP GAS Conversion Valve ConversionMaxitrol Valve Conversion Maintenance and Service Please NoteParts List Parts View FBB4 Optional Variable Speed Blower Installation WiringBlower Motor Blower WheelsVolt AC Junction BOX Wiring Installation Instructions Optional Brick Liner Installation InstructionsAccessories Accessory Description Model NumberHerringbone Aged BrickDecorative Accessories Mission Arch LeafLeaf Rectangle Mission Rectangle Plain Rectangle Leaf Arch Mission Arch Plain ArchHOW to Order Repair Parts Service NotesService Notes Service Notes Service Notes Comfort Systems

2, 1, DVD32FP3, 3)(N specifications

Empire Comfort Systems has long been a staple in the heating industry, offering innovative solutions for home heating needs. Among their impressive lineup, the Empire Comfort Systems 3)(N,1,2,DVD32FP3 stand-out model highlights a blend of traditional craftsmanship and modern technology. This fireplace insert is designed to provide warmth and an inviting atmosphere to any living space.

One of the primary features of the DVD32FP3 is its impressive efficiency. The unit is fueled by natural gas, which not only ensures a dependable heat source but also provides relatively lower operational costs. This model boasts a high efficiency rating, allowing homeowners to enjoy significant savings on utility bills while keeping the environment in mind. Its design allows for efficient heat distribution, ensuring that warmth fills the room without excessive energy consumption.

The Empire 3)(N,1,2,DVD32FP3 also emphasizes user convenience with its innovative controls. It features an adjustable thermostat that allows users to set their desired temperature easily, enhancing comfort levels within the home. A remote control option is also available, adding an extra layer of convenience for adjusting the fireplace settings from anywhere in the room.

Aesthetic appeal is another highlight of this model. With its sleek, contemporary design, the DVD32FP3 can blend seamlessly with various home decors. The unit is equipped with a large viewing window, providing a stunning visual of the flames while also giving a cozy ambiance to the space. The realistic log set enhances the appearance, mimicking the beauty of a traditional wood-burning fireplace without the hassle of wood maintenance.

Safety is of paramount importance with the Empire Comfort Systems 3)(N,1,2,DVD32FP3. It comes with a built-in safety sensor which ensures that the unit operates safely, providing peace of mind to homeowners. Additionally, its zero-clearance design allows for installation in various spaces without needing excessive modifications to existing structures.

Durability is a key characteristic of this fireplace insert, crafted from quality materials that promise longevity in performance. This makes it a reliable choice for home heating needs that can withstand the test of time and usage.

Overall, Empire Comfort Systems 3)(N,1,2,DVD32FP3 stands out for its combination of efficiency, aesthetic appeal, user-friendly features, and safety measures, making it an excellent choice for homeowners looking for comfort and reliability in their heating solutions. Whether you're nestled by the fire on a cold winter night or enhancing your living space, it's a perfect choice for warmth and style.
Top Page Image Contents