Empire Comfort Systems 1, DVD32FP3, 3)(N Junction BOX Wiring Installation Instructions

Page 53

JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS

STANDARD MILLIVOLT VALVE MODELS

CAUTION: ALLWIRING SHOULD BE DONE BYA QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE WITH ALL LOCAL, CITY AND STATE BUILDING CODES. BEFORE MAKING THE ELECTRICAL CONNECTION, MAKE SURE THAT MAIN POWER SUPPLY IS DISCONNECTED. THE APPLIANCE, WHEN INSTALLED, MUST BE ELECTRI- CALLY GROUNDED IN ACCORDANCE WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL ELECTRICAL CODE ANSI/NFPA 70 (LATEST EDITION).

A factory installed junction box is located on the lower right side of the fireplace. Wiring must be fed to the junction box and attached to the receptacle that is provided. Leave approximately 6" of wire in the junction box for connection.

Attach black wire to one side of the receptacle and white wire to opposite side of receptacle. The ground wire should be attached to the green (ground) screw.

Install the receptacle into the junction box. Attach cover plate.

120V DIRECT IGNITION VALVE MODELS

1.To wire Junction Box Receptacle, remove the tab on the side of the receptacle (hot side) to split receptacle. This will be required to separate blower and valve circuits.

2.Power for switched and live sides of Duplex Receptacle must come from the same power source. (One circuit breaker on main panel must switch all power off.)

3.From the wall box to the fireplace a 3-wire conductor with ground is recommended, however (2) two-wire conductors with grounds may be used in place of a 3-wire conductor with a ground if the black wires from the thermostat and blower switch are identified.

4.Two wall switches, or a wall switch and thermostat may be used to activate the two receptacle plugs independently.

OPTIONAL BRICK LINER INSTALLATION INSTRUCTIONS

1.Using gloves, unpack liner components and check for damaged or missing components.

2.Lower bottom louver and remove upper louver on fireplace.

3.Remove glass frame assembly from fireplace.

4.Remove rear logs from burner assembly.

5.Place brick panel (rear) against rear wall in fireplace.

Note: The top edge will have a half-moon cutout relief to match up with the rear flue vent hole.

6.While holding the front finished edge of a side brick panel (left & right), place brick panel (sides) against side walls in fireplace. NOTE: The side brick panels should be installed with full brick pattern at the bottom. Move side panels rearward until the back edge meets the rear brick panel. Slide

side brick panels down so they rest on firebox bottom, and brick joints match up with the back brick panel.

7.Align grout lines on top brick panel with the grout lines on the side brick panels. Place the top brick panel into brick panel holder. With needle-nose pliers, carefully bend hold-down tabs on brick panel holder over the edges of the top brick panel. The hold-down tabs will securely hold the top brick panel in place.

8.Replace rear logs onto burner assembly. (Refer to log placement, pages 36 and 37.

9.Attach glass frame assembly onto fireplace.

10.Raise bottom louver and replace top louver onto fireplace.

11.Installation of optional brick liner is complete.

23552-4-0408

Page 53

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Installation Instructions Table of Contents Important Safety Information LP-GAS Warning Odor Safety Information for Users of LP GASKeep Clear of ALL Obstructions Requirements for MassachusettsIntroduction DVVK-4TSP SpecificationsDVVK-4TP DVVK-4RPDVD32 DVD36 DVD42 DVD48 Fireplace DimensionsDim Clearances Mantel Chart FigureClearance to Combustibles Combustible MaterialLocating Fireplace GAS Supply Installing a New Main Gas CockRecommended Gas Pipe Diameter Checking Manifold PressuresConverting flue take-off to rear venting Rear Vent ConversionSpecial Vent Systems Vent Pipe Clearance InstallationFraming and Finishing Finishing Figures 13 Flush Mount Mantel Installation FigureFraming Figure VERTICAL, 90 Elbow with Horizontal Termination Flush Wall InstallationVERTICAL, 90 Elbow to Horizontal OUT the Wall Horizontal ONLY, Straight OUT the BackDim Venting Fireplace TOP Venting Graph Dimensions in FeetTo Use the Vent Graph Figure Example aVenting Fireplace TOP Below Grade InstallationCutting the Hole Figures Fireplace Hard Elbow Dimensions SeriesFireplace Flex Pipe 90 Degree Bend Series Positioning the FireplaceExamples TOP Vent RUN Venting Fireplace Rear Examples Rear Vent RUN Information on Various Venting Routes and Components Vertical Sidewall InstallationsTermination Clearances Vent Clearances Special Venting Components Simpson Duravent Installing Vent Components FigureVent System Identification Installing Firestops Installing Support Brackets FigureFraming and Finishing Horizontal Firestops FigureSee Horizontal Termination Page 29 and Vertical Termination Vertical Firestops Figures 40, 41Horizontal Termination Parts Verification DVVK-4RE Vent KIT Installation InstructionsInstalling Wall Thimble/Firestop Assembly DVVK-4RE Vent KIT Installation Instructions Connecting to Rigid Vent System Parts ListDVVK-4F Flex Vent Instructions InstallationInstalling the Vent System in a Chase General MaintenanceVertical Termination Determining Minimum Vent Height Above the RoofReassembly and Resealing Vent Pipe System Installation of Vertical Inlet BaffleEmber Material Placement on Burner LOG Placement 5 LOG SETLOG Placement 7 LOG SET Millivolt System Operating InstructionsInitial Lighting Pilot Flame FigureTRW Standing Pilot Wiring Diagram Personal injury or loss of life Standing Pilot Lighting InstructionsFrequent pilot outage problem Standing Pilot TroubleshootingPilot and main burner extinguish while in operation Glass sootsElectric 120 volt Operated Remote Control Frec Direct Ignition Wiring DiagramOptional Remote Control What to do if YOU Smell GAS Direct Ignition Lighting InstructionsInitial Start UP GAS Line Purge Direct Ignition TroubleshootingSymptom Check Action Valve Conversion Direct Ignition PROPANE/LP GAS ConversionMaxitrol Valve Conversion Please Note Maintenance and ServiceParts List Parts View Wiring FBB4 Optional Variable Speed Blower InstallationBlower Motor Blower WheelsVolt AC Optional Brick Liner Installation Instructions Junction BOX Wiring Installation InstructionsAccessory Description Model Number AccessoriesHerringbone Aged BrickMission Arch Leaf Decorative AccessoriesLeaf Rectangle Mission Rectangle Plain Rectangle Leaf Arch Mission Arch Plain ArchService Notes HOW to Order Repair PartsService Notes Service Notes Service Notes Comfort Systems

2, 1, DVD32FP3, 3)(N specifications

Empire Comfort Systems has long been a staple in the heating industry, offering innovative solutions for home heating needs. Among their impressive lineup, the Empire Comfort Systems 3)(N,1,2,DVD32FP3 stand-out model highlights a blend of traditional craftsmanship and modern technology. This fireplace insert is designed to provide warmth and an inviting atmosphere to any living space.

One of the primary features of the DVD32FP3 is its impressive efficiency. The unit is fueled by natural gas, which not only ensures a dependable heat source but also provides relatively lower operational costs. This model boasts a high efficiency rating, allowing homeowners to enjoy significant savings on utility bills while keeping the environment in mind. Its design allows for efficient heat distribution, ensuring that warmth fills the room without excessive energy consumption.

The Empire 3)(N,1,2,DVD32FP3 also emphasizes user convenience with its innovative controls. It features an adjustable thermostat that allows users to set their desired temperature easily, enhancing comfort levels within the home. A remote control option is also available, adding an extra layer of convenience for adjusting the fireplace settings from anywhere in the room.

Aesthetic appeal is another highlight of this model. With its sleek, contemporary design, the DVD32FP3 can blend seamlessly with various home decors. The unit is equipped with a large viewing window, providing a stunning visual of the flames while also giving a cozy ambiance to the space. The realistic log set enhances the appearance, mimicking the beauty of a traditional wood-burning fireplace without the hassle of wood maintenance.

Safety is of paramount importance with the Empire Comfort Systems 3)(N,1,2,DVD32FP3. It comes with a built-in safety sensor which ensures that the unit operates safely, providing peace of mind to homeowners. Additionally, its zero-clearance design allows for installation in various spaces without needing excessive modifications to existing structures.

Durability is a key characteristic of this fireplace insert, crafted from quality materials that promise longevity in performance. This makes it a reliable choice for home heating needs that can withstand the test of time and usage.

Overall, Empire Comfort Systems 3)(N,1,2,DVD32FP3 stands out for its combination of efficiency, aesthetic appeal, user-friendly features, and safety measures, making it an excellent choice for homeowners looking for comfort and reliability in their heating solutions. Whether you're nestled by the fire on a cold winter night or enhancing your living space, it's a perfect choice for warmth and style.
Top Page Image Contents