Empire Comfort Systems 2, 1 Standing Pilot Lighting Instructions, Personal injury or loss of life

Page 41

STANDING PILOT LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage,

personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.Before lighting smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

What To Do If You Smell Gas

•Do not try to light any appliance.

•Do not touch any electrical switch;

•Do not use any phone in your building.

•Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it; call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS

1.Stop! Read the safety information above.

2.Set REMOTE/OFF/ON switch to OFF.

3.Turn off all electric power to the appliance (if applicable).

4.Lower bottom louver assembly.

5.Push in gas control knob slightly and turn clockwise to "OFF."

REMOTE

OFF

ON

GAS CONTROL KNOB SHOWN

IN "OFF" POSITION

Note: Knob cannot be turned from "PILOT" to "OFF" unless knob is pushed in slightly. Do not force.

6.Wait ten (10) minutes to clear out any gas. Then smell for gas, including near the floor. If you then smell gas, STOP! Follow "B" in the safety information above. If you do not smell gas, go to the next step.

7.Find pilot - Follow metal

tube from gas control. The pilot is THERMOCOUPLEELECTRODE

behind the burner on the right side.

PILOT

THERMOPILE

 

8.Turn gas control knob

counterclockwise to "PILOT."

9.Push in control knob all the way and

hold in. Repeatedly push the piezo ignitor button until the pilot is lit. Continue to hold the control knob in the for about one (1) minute after the pilot is lit. Release knob, and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 5 through 9.

•Ifthecontrolknobdoesnotpopupwhenreleased, STOP and IMMEDIATELY call a qualified service technician or gas supplier.

•If the pilot will not stay lit after several tries, turn the gas control knob to "OFF" and call your service technician or gas supplier.

10.Turn gas control knob counterclockwise to "ON."

11.Close bottom louver assembly.

12.Turn on all electric power to the appliance (if applicable).

13.Set REMOTE/OFF/ON switch to desired setting.

TO TURN OFF GAS TO FIREPLACE

1.Set REMOTE/OFF/ON switch to OFF.

2.Turn off all electric power to the appliance if service is to be performed (if applicable).

3.Lower bottom louver assembly.

4.Push in gas control knob slightly and turn clockwise to "OFF." Do not force.

5.Close bottom louver assembly.

23552-4-0408

Page 41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Installation Instructions Table of Contents Important Safety Information LP-GAS Warning Odor Safety Information for Users of LP GASKeep Clear of ALL Obstructions Requirements for MassachusettsIntroduction DVVK-4TSP SpecificationsDVVK-4TP DVVK-4RPDVD32 DVD36 DVD42 DVD48 Fireplace DimensionsDim Clearances Mantel Chart FigureClearance to Combustibles Combustible MaterialLocating Fireplace GAS Supply Installing a New Main Gas CockRecommended Gas Pipe Diameter Checking Manifold PressuresConverting flue take-off to rear venting Rear Vent ConversionSpecial Vent Systems Vent Pipe Clearance InstallationFraming and Finishing Finishing Figures 13 Flush Mount Mantel Installation FigureFraming Figure VERTICAL, 90 Elbow with Horizontal Termination Flush Wall InstallationVERTICAL, 90 Elbow to Horizontal OUT the Wall Horizontal ONLY, Straight OUT the BackDim Venting Fireplace TOP Venting Graph Dimensions in FeetTo Use the Vent Graph Figure Example aVenting Fireplace TOP Below Grade InstallationCutting the Hole Figures Fireplace Hard Elbow Dimensions SeriesFireplace Flex Pipe 90 Degree Bend Series Positioning the FireplaceExamples TOP Vent RUN Venting Fireplace Rear Examples Rear Vent RUN Information on Various Venting Routes and Components Vertical Sidewall InstallationsTermination Clearances Vent Clearances Special Venting Components Simpson Duravent Installing Vent Components FigureVent System Identification Installing Firestops Installing Support Brackets FigureFraming and Finishing Horizontal Firestops FigureSee Horizontal Termination Page 29 and Vertical Termination Vertical Firestops Figures 40, 41Horizontal Termination Parts Verification DVVK-4RE Vent KIT Installation InstructionsInstalling Wall Thimble/Firestop Assembly DVVK-4RE Vent KIT Installation Instructions Connecting to Rigid Vent System Parts ListDVVK-4F Flex Vent Instructions InstallationInstalling the Vent System in a Chase General MaintenanceVertical Termination Determining Minimum Vent Height Above the RoofReassembly and Resealing Vent Pipe System Installation of Vertical Inlet BaffleEmber Material Placement on Burner LOG Placement 5 LOG SETLOG Placement 7 LOG SET Millivolt System Operating InstructionsInitial Lighting Pilot Flame FigureTRW Standing Pilot Wiring Diagram Personal injury or loss of life Standing Pilot Lighting InstructionsFrequent pilot outage problem Standing Pilot TroubleshootingPilot and main burner extinguish while in operation Glass sootsElectric 120 volt Operated Remote Control Frec Direct Ignition Wiring DiagramOptional Remote Control What to do if YOU Smell GAS Direct Ignition Lighting InstructionsInitial Start UP GAS Line Purge Direct Ignition TroubleshootingSymptom Check Action Valve Conversion Direct Ignition PROPANE/LP GAS ConversionMaxitrol Valve Conversion Please Note Maintenance and ServiceParts List Parts View Wiring FBB4 Optional Variable Speed Blower InstallationBlower Motor Blower WheelsVolt AC Optional Brick Liner Installation Instructions Junction BOX Wiring Installation InstructionsAccessory Description Model Number AccessoriesHerringbone Aged BrickMission Arch Leaf Decorative AccessoriesLeaf Rectangle Mission Rectangle Plain Rectangle Leaf Arch Mission Arch Plain ArchService Notes HOW to Order Repair PartsService Notes Service Notes Service Notes Comfort Systems

2, 1, DVD32FP3, 3)(N specifications

Empire Comfort Systems has long been a staple in the heating industry, offering innovative solutions for home heating needs. Among their impressive lineup, the Empire Comfort Systems 3)(N,1,2,DVD32FP3 stand-out model highlights a blend of traditional craftsmanship and modern technology. This fireplace insert is designed to provide warmth and an inviting atmosphere to any living space.

One of the primary features of the DVD32FP3 is its impressive efficiency. The unit is fueled by natural gas, which not only ensures a dependable heat source but also provides relatively lower operational costs. This model boasts a high efficiency rating, allowing homeowners to enjoy significant savings on utility bills while keeping the environment in mind. Its design allows for efficient heat distribution, ensuring that warmth fills the room without excessive energy consumption.

The Empire 3)(N,1,2,DVD32FP3 also emphasizes user convenience with its innovative controls. It features an adjustable thermostat that allows users to set their desired temperature easily, enhancing comfort levels within the home. A remote control option is also available, adding an extra layer of convenience for adjusting the fireplace settings from anywhere in the room.

Aesthetic appeal is another highlight of this model. With its sleek, contemporary design, the DVD32FP3 can blend seamlessly with various home decors. The unit is equipped with a large viewing window, providing a stunning visual of the flames while also giving a cozy ambiance to the space. The realistic log set enhances the appearance, mimicking the beauty of a traditional wood-burning fireplace without the hassle of wood maintenance.

Safety is of paramount importance with the Empire Comfort Systems 3)(N,1,2,DVD32FP3. It comes with a built-in safety sensor which ensures that the unit operates safely, providing peace of mind to homeowners. Additionally, its zero-clearance design allows for installation in various spaces without needing excessive modifications to existing structures.

Durability is a key characteristic of this fireplace insert, crafted from quality materials that promise longevity in performance. This makes it a reliable choice for home heating needs that can withstand the test of time and usage.

Overall, Empire Comfort Systems 3)(N,1,2,DVD32FP3 stands out for its combination of efficiency, aesthetic appeal, user-friendly features, and safety measures, making it an excellent choice for homeowners looking for comfort and reliability in their heating solutions. Whether you're nestled by the fire on a cold winter night or enhancing your living space, it's a perfect choice for warmth and style.
Top Page Image Contents