Karcher 600 CD manual Operating parameters, Lim

Page 75

WTC 600 LP / MP

APPENDIX

3.2Operating parameters

The control system allows the following operating parameter settings (realization see item 4). The resulting behaviours are described in the chapter operating conditions. The values in brackets are the standard values after system reset (see item 4.4.4).

LIM

function:

Permeate limit value used to switch the unit off in

 

 

case limit is exceeded or if a DISPOSAL process

 

 

is to be finished. If this value is exceeded during

 

 

PRODUCTION, RINSE or CONCENTRATE

 

 

DISPLACEMENT/FLUSH for the time defined for

 

 

t-delay LIM, an ALARM MESSAGE will be

 

 

activated.

 

right of access:

user/technician

 

possible setting: meas. range 0.5-50µS/cm (40 µS/cm)

 

 

Attention: the set value must be above aaLIM

aaLIM

function:

Permeate limit value activating an ALARM

 

 

MESSAGE in the display and on/off of the

 

 

malfunction LED if this value is exceeded for the

 

 

time defined for t-delay aaLIM

 

right of access:

user/technician

 

possible setting:

0.5-50µS/cm (10 µS/cm)

 

 

Attention: the set value must be lower than LIM

t-delay LIM

function:

Time delay for wrong permeate limit value

 

 

(see above)

 

right of access:

technician

 

possible setting:

0-99 min (1 min)

t-delay aaLIM

function:

Time delay for advance alarm in case of wrong

 

 

permeate limit value (see above)

 

right of access:

technician

 

possible setting:

0-99 min (5 min)

t-delay lack of pressure

function:

Time delay to release PRESSURE FAILURE if

 

 

PRESSURE SWITCH is inactive.

 

right of access:

technician

 

possible setting:

0-99s (1s)

t-delay at start

function:

Period of time of permanent pressure at start of

 

 

 

operation after opening of the inlet valve before

 

 

 

the pumps begin to work.

 

 

right of access:

technician

 

 

possible setting:

0-9.9s (0.5s)

t-pressure available

function:

Period of time until PRESURE FAILURE is

 

 

 

released if pumps do not start after opening of

 

 

 

inlet valve.

 

 

right of access:

technician

 

 

possible setting:

0-99s (5s)

t rinse

function:

Duration of a DISCONTINUOUS RINSE.

 

 

right of access:

technician

 

 

possible setting:

0-99 min (5s)

 

 

 

 

Service Handbook 08.2004

 

75

Page 74 Page 76
Image 75
Page 74 Page 76
Contents LP/MP, PI Foreword ForewordWTC 600 LP / MP Contents2.5 MaintenanceMalfunction, Cause and Corrective Action Maintenance PlanWTC 600 LP / MP Intended Use Introduction Marking of InstructionsSafety Instructionse Milliliter = 1 liter 1000 mg = General installation notesUnits and Designations Handling Electricity / Protection ClassOverview Overview of components Service HandbookDescription Flow Diagram Flocculation Module Description of the SystemModular Design Pre-chlorination ModuleAnti Scalant and Post Chlorination Mediafilter- and Activated Carbon FilterRO System, Pump and Fine Filter Control Panel and DisplayPressure-increase Pump Safety Installations Emergency StopRC Protective Switch Motor Protection SwitchOperating Modes Automatic Operation Standard Operating Mode MicrofusesManual Operation Parameter WTC 600 LP WTC 600 MP Technical Data WTC 600 LP/MPDimensions H x W x D Weight in delivery condition without filter containerFilter amounts, activated carbon filter Float SwitchFilter Container Filling capacities, MediafilterProduct ItemNo Cleaning Chemicals Product Item NoConsumption Materials Chemicals for Metering ContainerAssembly and Starting Operation Assembly ChapterStarting Operation Chapter Mixing Chlorine, Flocculation Agent and Antiscalant First fill of the metering tanksPre-chlorination Calculation example Antiscalant Work Steps Mixing of the flocking test solution AuxiliariesMetering Amounts and Mixing of the Post Chlorination Flocculation AgentEvaluate flocking test Perform flocking test AuxiliariesConnections, Valves and Indicators Connecting the EquipmentRO Module with Preliminary Filters Pressure-increase ModuleElectrical Connections Pressure-increase Pump Preliminary FilterMetering Station WTC 600 LP / MP Starting Operation Reverse Osmosis SystemModul Lift Frequency Meter 14/1 14/4 Ing Backwashing / Regeneration Initial FillingMedia and Activated Carbon Filter Filter Support pebbles Filter sand / Activated carbonPosition Indication Description ProgrammingIndication Description Menu Selection Technician passwordUser Level Technician LevelDe-conserving Adjusting Operating Parameters and Balancing ValuesSelecting Several Arguments at the Same Acknowledging Data InputsIndication System in disinfection operating mode Untreated Drinking water Concentrade Yield Water Capacity Initial startupKeys to call up menu item 6 LF limits User indication in normal operation Normal OperationOperating Messages for Normal Operation Putting Out of Operation Desinfection Fine Filter Metering Station WTC 600 CDEvery 4 weeks Replacing the membrane RO Filter ReplacementFilter replacement Reverse Osmosis Module RO ModuleAssembly and disassembly of the RO filter Cleaning in Case of MalfunctionDesign of the Flushing and Disinfection Equipment AidsStarting Position Work Steps Disinfection Acidic and Alkaline Cleaning Conserve the RO system Starting Position Drain the pre-filter Flushing the pre-filter Replace the activated carbon or filter sand Spare parts requiredSpare parts possibly required Disposing of the replaced filter material Indication Malfunction Cause Corrective Action Chap Malfunction, Cause and Corrective ActionMalfunction Indication at the Operating Panel Indication of RO Fuse defective Have replaced by Chap./Fig Maintenance Plan Maintenance Plan Service Module Work to be Carried Out Other MaintenanceGWV RO control factory settingsWTC 600 MP, MP-A, MP-AM in voltages 230 V and 400 Operating mode Switched offRO control program structure Appendix RO 1000 Manual ManualContents Technical Data Scope of Application General RemarksInstructions for Use Safety InstructionsTerms and Definitions Declaration of ConformityScript Examples Start-up Code Function Adm. max. load Terminal Function of TerminalsNot switch off Operational Scope Operating settingsLIM Operating parametersAppendix Stop Operating conditions Forced Stop active Pressure Switch activeOperating failures/failure messages Denomination Reason ConsequenceText display Indicator lightsOperation User interface KeyboardSelection Password entryBasic elements Selection of menuConfirmations MultiselectionNumerical editing Alphanumerical editingTechnicians level Operating levelsUsers Level Menu structure Menu point Function Main menuMax Cy Calibration menuDiagnosis menu Setting menuMin Type Max Unit Technical DataOperating Record for the WTC 600 LP/MP Automatic Operation List of KEY Words Units and Designations

600 CD specifications

The Karcher 600 CD is an innovative cleaning machine designed to tackle a wide variety of dirt and grime in both professional and domestic settings. Renowned for its efficiency, versatility, and user-friendly design, this powerful equipment is particularly well-suited for cleaning large areas such as driveways, patios, and commercial spaces.

One of the standout features of the Karcher 600 CD is its robust pressure cleaning capability. It boasts a maximum pressure output that effectively removes stubborn stains, embedded dirt, and even algae with minimal effort. The adjustable pressure settings offer the flexibility needed for different surfaces, ensuring that delicate materials are not damaged while still achieving optimal cleaning results.

The Karcher 600 CD employs advanced cleaning technologies such as the patented Dual Nozzle System. This feature ensures a consistent and thorough clean by utilizing two high-pressure nozzles that work in unison. The nozzles are adjustable, allowing users to customize the spray pattern according to the task at hand. Whether it’s rinsing large surfaces or precision cleaning in tight spots, the Karcher 600 CD excels in delivering superior results.

In terms of ergonomics, the Karcher 600 CD is designed for user comfort. It features a lightweight and compact build that allows for easy maneuverability, even in hard-to-reach areas. The integrated handle and wheels enhance portability, making it effortless to transport the machine from one location to another.

Energy efficiency is another key characteristic of the Karcher 600 CD. The machine is engineered to consume less water and energy while still providing powerful cleaning performance. This eco-friendly aspect not only reduces operational costs but also aligns with sustainable cleaning practices.

Furthermore, the Karcher 600 CD comes with a range of accessories and attachments that enhance its functionality. Users can switch between different cleaning tasks seamlessly, whether it’s washing vehicles, cleaning decks, or revitalizing outdoor furniture.

The Karcher 600 CD stands out in the cleaning equipment market for its combination of power, versatility, and efficiency. With its user-centric design and advanced features, it is ideal for homeowners and professionals alike who seek effective and reliable cleaning solutions.
Top Page Image Contents