Honeywell LYNXR24 manual 6FKHGXOH, = the value that was last stored in the memory

86(5￿)81&7,216￿

6FKHGXOLQJ￿8VHU￿,QWHUIDFH￿

NOTE: The keypad beeps twice for invalid data entries (e.g.: an hour greater than 12), and the entry will not be accepted. The keypad beeps once for valid entries and four times when a schedule event is programmed successfully.

[x] = the value that was last stored in the memory.
			6FKHGXOH
					Enter the 1-digit schedule number to be programmed, then
	￿[￿	Q￿	>[@￿@	PRGHVFKFRQWLH[LWVFKHGXOHQXPEHUQPEHUSURJUDPPLQJ￿WR￿	press [*] to accept and advance to the next programming field:
					Event Identifier.
					• Press the [#] key in this entry will exit the schedule
					programming mode. The keypad will beep four times and
					exit.
					• Schedule number 7 and 8 are always random events that
					are meant to work only with X-10 devices.
					NOTE: This feature should be implemented when the user is
					trying to give the impression that a premises is “lived in”.
			￿		The events will occur at random times (0-59 minutes)
					within the defined hour.
			(YHQW,GHQWLILHU		0 = Empty - no event scheduled (or schedule temporarily
	￿￿[￿	LG￿	>￿[@@	HYHQWLGHQWLILHUFRQWLXHUHWXUQWRSUHYLRXVSURPSW￿WR￿	disabled. Keypad will beep four times and return to
					Schedule Number with the schedule number advanced.
					1 = X-10 Device - the user is required to enter data up to and
					include the Device Number screen. Selection #1 is a time
					driven event that requires a begin and end time.
					2 = Latch Key Report - the user is required to enter data up
					to and include the End Day screen. Selection #2 is a window
					driven event that requires a begin/end time.
					3 = Automatic Stay Arming - the user is required to enter
					data up to and include the Begin Day screen. Selection #3 is
					a time driven event that requires a begin time to send a
					report.
					4 = Reminder Announcements - the user is required to enter
					data up to and include the Begin Day screen. This is a
					reminder announcement.
					5 = Alarm Clock - the user is required to enter the field
					values up to and include the Begin Day screen. This is a an
					alarm clock.
					NOTES: (1) See figure 1 for an explanation of each entry of the
					event identifier.
					(2) If “Follow me” reminder telephone number is
					programmed, the reminder announcement is also
					delivered to that number.
					• The begin hour is a two-digit entry. To enter the hour 3,
	[[￿￿￿￿$E￿		>%HJLQ￿[[@@FRQWLXHFRQWLXHEJLQWLPHUUWXUQ7LPHEHJLQWXUQ￿WRWRKRXUDPSUHYLRXV￿￿S￿￿￿P￿WR￿$3￿￿￿SURPSWSURPSW		press “0” followed by “3”.
					• The begin hour “00” indicates this schedule does not have
					a begin time.
					• Press “0” to select AM or “1” to select PM.
					NOTE: When programming schedule number 7 and 8, do not
					program turn on/off to occur within the same 1-hour
					period. This will prevent this random feature from
					causing a reversal of the on/off times.

– 29 –