Bosch Appliances FW5.50 software manual Enable, Multicast Address

Page 86

86 en Network	Camera Browser Interface

14.3Multicast

The camera can enable multiple receivers to receive the video signal simultaneously. The stream is either duplicated and then distributed to multiple receivers (Multi-unicast), or it is sent as a single stream to the network, where it is simultaneously distributed to multiple receivers in a defined group (Multicast).

Multicast operation requires a multicast-enabled network that uses UDP and the Internet Group Management protocol (IGMP V2). The network must support group IP addresses. Other group management protocols are not supported. The TCP protocol does not support multicast connections.

A special IP address from 225.0.0.0 to 239.255.255.255

(class D address) must be configured for multicast operation in a multicast-enabled network. The multicast address can be the same for multiple streams, however, it is necessary to use a different port in each case.

The settings must be made individually for each stream. Enter a dedicated multicast address and port for each stream. Switch between the streams by clicking the appropriate tabs.

14.3.1Enable

Enable simultaneous data reception on receivers that need to activate the multicast function. To do this, check the box and enter the multicast address.

14.3.2Multicast Address

Enter a valid multicast address to be operated in multicast mode (duplication of the data stream in the network).

With a 0.0.0.0 setting, the encoder for the stream operates in multi-unicast mode (copying of data stream in device). The camera supports multi-unicast connections for up to five simultaneously connected receivers.

AM18-Q0611 v5.50 2012.03

Software manual

Bosch Security Systems

Image 86

Contents Camera Browser Interface Page Table of Contents Advanced General Settings Web InterfaceEncoder Settings CameraAlarm RecordingSetting up VCA Interfaces NetworkService Browser connection System requirementsProtected network Password protection in cameraEstablishing the connection 192.168.0.1Livepage SettingsSystem Overview RecordingsOperation via the browser Image selectionStatus icons Storage discovery Cameras with PTZ controlMotion flag Pan and tiltPre-position Cameras with alarm and relay I/OSystem Log / Event Log Running recording program Saving snapshotsRecording video sequences Audio communication Processor loadSelecting Recordings Export to FTPSlide control Controlling playbackControl buttons Bookmarks Basic Mode Advanced Mode Settings OverviewConfiguration Menu Saving changes NavigationMaking Changes Password Basic ModeDevice Access NamingDate/Time PasswordConfirm password Device date, time and zoneIP address Click Set and RebootNetwork Subnet maskRecording EncoderAudio System Overview1 ID Advanced General SettingsIdentification ISCSI Initiator extensionPassword Confirm passwordDevice time zone Date formatDevice date / Device time Daylight saving timeTime server IP address Time server typeCamera name stamping Alarm mode stampingDisplay Stamping Time stampingAlarm message Video watermarkingWeb Interface AppearanceLivepage Functions Allow local recording Show system logAllow snapshots Frame only streamSave system log LoggingSave event log File for event logInstaller Menu CameraPicture Settings White balance2 Day/Night Encoder Settings Pixel Counter Select G.711, L16 or AAC* as the audio Recording formatEncoder Settings Changing a profile Encoder ProfilePre-defined profiles Target bit rate Standard definition video resolutionProfile name Maximum bit rateExpert Settings Default Encoder Streams 1 H.264 settingsSelect H.264 Settings PreviewJpeg stream Recording Recording media Storage ManagementDevice manager ISCSI MediaActivating and configuring storage media Formatting storage media Deactivating storage mediaRecording includes Stream profile settingsRecording Profiles Standard recording Alarm recordingRecording track selection Alarm triggers Motion/Audio alarm Video loss alarmRetention Time Holidays Recording SchedulerWeekdays Recording status Profile namesActivate recording Recording Status Alarm Alarm ConnectionsRemote port Video transmissionStream Video outputAudio SSL encryptionAuto-connect Video Content Analyses VCA Audio Alarm Alarm E-Mail Sender name Attach Jpeg from cameraDestination address Test e-mailSetting up VCA VCA Silent MOTION+VCA Profiles Aggregation time sSensitivity Analysis typeMotion detector Debounce time 1 s Tamper detectionMinimum object size Selecting the areaGlobal change Trigger delay sGlobal change slider Scene too brightReference check Scene too darkScene too noisy Appearing edges VCA Scheduled Deleting Holidays Trigger Delay sVCA Event triggered Trigger activeRelay Alarm inputInterfaces Automatic IP assignment Network AccessNetwork IP V4 addressHttp browser port IP V6 addressDNS server address Https browser portTelnet support Interface mode ETH14.1.8 RCP+ port Network MSS ByteHost name Enable DynDNSNetwork MTU Byte User nameStatus Snmp AuthenticationAdvanced 14.2.2 1. Snmp host address / 2. Snmp host addressUPnP Quality of ServiceRtsp port TCP metadata inputMulticast Address EnableMulticast Multicast packet TTL PortStreaming FTP server FTP PostingJpeg posting Path on FTP server FTP server passwordIP V4 filter Firmware ServiceMaintenance Configuration SSL certificateMaintenance log Page Bosch Security Systems