First Alert FA148CPSIA, FA168CPSSIA manual Rcvr Jam, Or Check, Alarm, Fault

Page 40

Trouble Conditions (Continued)

Other Trouble

Displays

*Any “beeping” that accompanies a trouble display can be stopped by depressing any key on the keypad or by entering an OFF sequence (code + OFF)

**Not all systems use wireless sensors.

Words or letters in parentheses ( ) are those that are displayed on Alpha Display keypads.


COMM. FAILURE	Indicates that a failure has occurred in
(or FC)	the telephone communication portion of
	your system. CALL FOR SERVICE.
SYSTEM LO BAT	Indicates that a low system battery
(or BAT with no	condition exists. Display is
zone No.)	accompanied by "beeping"* at the
	keypad. If this condition persists for
	more than one day (with AC present),
	CALL FOR SERVICE.
LO BAT	Indicates that there is a low battery
+ zone descriptor	condition in the wireless transmitter**
(or BAT with	number displayed (00 is RF keypad).
zone No.)	Accompanied by a single "beep"* (about
	once every 30 seconds) at the keypad.
	Either replace the battery yourself, or
	CALL FOR SERVICE. If the battery is
	not replaced within 30 days, a CHECK
	display may occur.
Rcvr Jam	Wireless part of the system is experiencing
(or CHECK 90)	RF interference which may impede
	reception from wireless sensors.**
ALARM 1xx	Indicates a communication problem
FAULT 1xx	between the control and a connected
CHECK 1xx	device (e.g., RF receiver, zone expander)
(or 91)	where the “xx” indicates the device
	address. CALL FOR SERVICE.

MODEM COMM	Indicates that the control is on-line with
(or CC)	the Central Monitoring Station's remote
	computer.
	The control will not report system
	activity while on-line. Wait a few minutes
	— the display should disappear.

BELL FAILURE	Indicates that the wiring connection to
(or CHECK 70)	the external sounder is at fault (open or
	shorted). Accompanied by “beeping” at
	the keypad. CALL FOR SERVICE.

– 40 –

Image 40

Contents FA168CPS / FA168CPSSIA FA148CP / FA148CPSIA About This Manual Table of Contents Using Device Commands Paging Feature Event Logging ProceduresPanic Keys Macro Key Programming & Usage Security Codes & Authority LevelsIntroduction System OverviewSystem Basics Alarms Memory of AlarmZones and Partitions Arming, Step-Arming and Disarming Burglary ProtectionPhone Access Using the Voice Message Center if Voice Keypad is installedMessage Center Functions About The Keypads General InformationFixed-Word Display Keypad Functions of the Keypads Display WindowStay Exit Delay Entry/Exit DelaysEntry Delay Exit Alarms Exit Error ConditionsTo turn the Voice Status feature on/off # Using the ∗ KeyChecking For Open Zones Arming the System Arming Commands Modes of Arming Press these keys… Keypad Confirms By…Quick Arming Function Key ArmingSingle Button Arming Step Arming FeatureKey First Press Second Press Third Press Using the Keyswitch Using the KeyswitchTo arm in the Away mode To arm in the Stay modeDisarming and Silencing Alarms Using the OFF keyUsing the Bypass Key Bypassing Protection ZonesQuick Bypass Chime Mode To turn Chime Mode onTo turn Chime Mode off To turn Voice Chime Mode on or offDate and Time Setting the Date and TimeViewing the Current Date and Time Using Panic Keys This Function Sends this signal With This Sounding…Panic Keys To activate a Panic FunctionMacro Key Programming & Usage About Macro KeysUsing a Programmed Macro Key Example of Macro ProgrammingUsing Device Commands About Device CommandsTo Activate Devices To Deactivate DevicesPaging Feature About Automatic PagingManual Paging Latch Key PagingAbout Security Codes Security Codes & Authority LevelsAuthority Level Definitions How to Assign Security Codes and Attributes Accessing Other Partitions FA168CPS About Accessing PartitionsUsing the GoTo Command Accessing Other PartitionsMulti-Partition Arming Common Zone Operation About Scheduling SchedulingCreating Schedules Group Number Partition Start Smtwtfs Event Logging Procedures About Event LoggingViewing the Event Log Understanding the Type of Event DisplayedTesting the System To Be Conducted Weekly About Testing the SystemCheck and Battery Displays Trouble ConditionsAlarm FaultRcvr Jam Or CheckBusy-Standby Long Rng TrblSilencing Low Battery Warning Tones at Keypad Maintaining Your SystemFire Alarm System If Installed This Section Applies only to Residential SystemsIndividual Keys Key PairsKitchen Dining Emergency Evacuation Function Procedure Comments Quick Guide to Basic System FunctionsSummary of Audible/Visual Notifications Fixed-Word Display KeypadsSummary of Audible/Visual Notifications Regulatory Statements and Warnings Federal Communications Commission FCC PartIndustry Canada FCC PartRegulatory Statements Industrie CanadaCharts of Your System’s Features Function Keys CommentsCharts of Your System’s Features User User’s Parts Security Auth Access RF Zone Pager No. † Paging Setup List of Output Devices Page Page Page Page OWNER’S Insurance Premium Credit Request Cont Limitations of this System ÊK5309-5V4DŠ