Kenmore 153.331592, 153.331492 owner manual Piezoelectric Igniter System

Page 32

compartment, making sure that the tip of the manifold tube engages in the slot of the bracket inside the combustion chamber (Figures 38 & 39).

4, Inspect the door gasket and make sure there is no fiberglass insulation between the gasket and the combustion chamber.

5, Replace the two screws, which secure the manifold/ burner assembly door to the combustion chamber and tighten securely. Once the manifold/burner assembly door is tightened, visually inspect the door gasket between the manifold/burner assembly door and the combustion chamber for spaces or gaps that would prevent a seal. IMPORTANT: Do not operate the water heater if the door gasket does not create a seal between the manifold door and the combustion chamber.

6, During the following procedure, do not cross-thread or apply any thread sealant to any of the fittings listed below. First, reconnect the manifold tubing to the gas control valve/ thermostat.

NOTE: If a ferrule nut needs to be installed for the pilot tube, locate the one provided with your parts kit. Install it in the gas control valve/thermostat at the pilot location, hand tight only.

Next, insert the pilot tube into the ferrule nut until it bottoms out. NOTE: Hold the tube in this position. Tighten the ferrule nut with a wrench until the crimp connection seals to the pilot tube. Continue to tighten until the nut is tight in the gas control valve/thermostat.

7, Plug the thermopile plug into the gas control valve/ thermostat. Also, connect the two wire leads that go to the thermal switch if they had been removed.

8, Reconnect the igniter wire and tank sensor plugs.

9.Turn gas supply on and refer to the Lighting Instructions.

10.With the burner tit, check the gas control valve/thermostat supply line, two piece wire connector, manifold tube, and pilot tube connections for leaks. Check for leaks by brushing on an approved noncorrosive leak detection solution. Bubbles forming indicate a leak. Correct any leak found. IMPORTANT: All leaks must be fixed immediately.

11.Replace the outer door.

CLOSE-UP INSIDE VIEW OF

THE COMBUSTION CHAMBER.

__SLOT

TIPBRACKET

MANIFOLD TUBE

FIGURE 39.

Piezoelectric Igniter System

The piezoelectric igniter system consists of the igniter button, electrode, and wire. The pilot is ignited by an electric spark generated when the igniter button is pressed. The spark gap of 0.125 inch is set when the electrode is installed at the factory. (Figure 40). Use only factory authorized piezoelectric igniter parts for replacement.

ELECTRONIC CONTROL MODULE

PILOT ASSEMBLY

PILOT

THERMOPILE

IGNITER

BUTTON

PILOT BRACKET

*NOTE: SPARK GAP DISTANCE MEASURED FROM ELECTRODE TIP TO PILOT.

FIGURE 40.

Testing the Igniter System

Turn off the gas to the water heater at the manual gas shut-off valve. Watch the electrode tip while activating the igniter. A visible spark should jump from the electrode. To avoid shock, do not touch the burner or any metal part on the pilot or pilot assembly. If no spark is visible, check the wire connections and make sure the electrode is not broken. Replace the igniter if defective. Dirt and rust on the pilot or electrode tip can prevent the igniter spark. Wipe clean with a damp cloth and dry completely. Rust can be removed from the electrode tip and metal surfaces by lightly sanding with an emery cloth or fine grit sandpaper.

FLAMEARRESTORBRACKET

TiP

FIGURE 38.

FVIR System Operational Checklist

1.Manifold gasket properly sealed.

2.Viewport not damaged or cracked.

3.Flame-arrestor free of debris and undamaged.

4.Two piece wire connector properly installed.

5.No leaks at pilot and manifold connection.

6.Manifold door screws securely tightened.

7.Depress the button on the thermal switch.

32

Image 32
Contents 153.331492 Gallon 153.331592 =iI=1,Ctd,,,it=Read and follow water heater warnings and instructions Important DefinitionsFire Hazard Improper installation and use may result in property damageFire or Explosion Harzard GAS Supply Troubleshootingguide Year Limited Warranty on Water Heater Excessive Weight Hazard Important Information About This Water HeaterMaterials Needed GET to Know Your Water Heater GAS Models Vent Pipe Inner Door Gas ControlInstallation Checklist Removing the Old Water HeaterC Manualgas SHUT-OFFVALVELocation Requirements Site LocationCarbon Monoxide Poisoning Hazard Fire or Explosion HazardClearances and Accessibility Insulation BlanketsProperty Damage Hazard Breathing Hazard Carbon Monoxide GasFilling the Water Heater Gas RequirementsGas Piping Explosion HazardGas Pressure Testing Gas PressureCarbon Monoxide Warning Unconfined SpaceAll Air from Inside the Building Confined SpaceAll Air from Outdoors Louvers and GrillesDraft Hood Installation Vent ConnectorsVent Pipe Size Vent Pipe SystemChimney Connection Vertical Exhaust Gas VentPiping Installation TvALvETemperature and Pressure Relief Valve Temperature & Pressure Relief ValveClosed System/Thermal Expansion Explosion HarzardLighting Instructions What to do if YOU Smell GASWater Temperature Regulation Checking the DraftBurner Flames Emergency Shut DownGascontroutemperatureknob Tank Sediment Cleaning Vent System InspectionBurner Inspection Caon Monoxide and Fire HazardTemperature-Pressure Relief Valve Operation HousekeepingAnode Rod Inspection Draining and FlushingService Full Assembly Electronic Control Module Replacement Parts External Inspection & Cleaning Base-Ring FilterRemoving the Burner from the Manifold Burner Assembly Removing the Manifold/Burner AssemblyCleaning the Combustion Chamber and Flame-arrestor Explosion HazardPiezoelectric Igniter System Expansion Tank Specifications Expansion Tank Sizing ChartStart Up Conditions Strange SoundsOperational Conditions Page Problemled Status Problem Page Page Page Page Page

153.331492, 153.331592 specifications

The Kenmore 153.331592 and 153.331492 are two innovative models in a series of versatile and efficient appliances designed to enhance everyday living. These products cater to a wide range of household needs, making them not only practical but also integral to modern home technology.

One of the standout features of the Kenmore 153.331592 is its energy efficiency. Designed with advanced technology, this model consumes less energy while providing robust performance. This is particularly important for environmentally conscious consumers looking to reduce their carbon footprint without compromising on effectiveness. The appliance utilizes smart energy management systems that optimize power use, ensuring that households can enjoy high performance with minimal energy costs.

On the other hand, the Kenmore 153.331492 offers impressive capacity, making it ideal for larger families or those who frequently entertain guests. This model is designed to accommodate substantial loads, whether it be laundry, cooking, or storage, making it a perfect fit for busy households. Additionally, its spacious design allows for easy organization, ensuring that items can be stored efficiently without clutter.

Both models incorporate advanced technology, including intuitive digital controls. These controls allow users to easily set preferences and monitor their appliance's operation through user-friendly interfaces. Smart connectivity features are also integrated into both models, allowing for remote management via smartphone apps. Users can adjust settings, receive alerts, and even perform diagnostics from the convenience of their phones, highlighting Kenmore's commitment to convenience and ease of use.

In terms of build quality, both models exhibit durable construction with high-quality materials designed to withstand the rigors of daily use. The sleek and modern design enhances their aesthetic appeal, making them suitable for any kitchen or laundry room decor.

Additionally, safety features such as auto shut-off, child locks, and overload protection are included in both models, ensuring that they operate smoothly without unnecessary risks.

In conclusion, the Kenmore 153.331592 and 153.331492 stand out for their blend of efficiency, capacity, and smart technology integration. These models present a compelling choice for those seeking reliable appliances that cater to both traditional and modern lifestyles. With a focus on energy conservation, user-friendly interfaces, and durable build quality, Kenmore continues to solidify its reputation as a leader in home appliance innovation.