Cisco Systems 4300E manual OL-25230-02

Page 16

Chapter 2 Getting Started

Installing the IP Camera

Table 2-1

 

Installing the IP Camera (continued)

 

 

 

 

 

 

 

 

Action

Explanation

 

 

 

 

 

Step 5

Optional. Use the GPIO ports on the rear of the IP

You can connect up to two input devices and two output

 

 

camera to connect external devices that trigger alarms

devices to these ports:

 

 

(connect through input ports) or respond to alarms

DI1—Alarm input 1

 

 

(connect through output ports).

 

 

DI2—Alarm input 2

 

 

 

 

 

 

 

 

DO1—Alarm output 1

 

 

 

 

DO2—Alarm output 2

 

 

 

 

GND—Ground (for use if needed)

 

 

 

 

 

Step 6

Optional. Use the RS-232 ports on the rear of the IP

A RS-232 cable fits into the ports in one way. Make sure

 

 

camera to connect a control device (motorized housing)

to insert it properly.

 

 

that supports the Pelco D protocol.

 

 

 

 

 

 

 

Step 7

Connect an STP (shielded twisted pair) Category 5 or

If your network provides PoE, the IP camera powers on.

 

 

higher network cable to the LAN port on the back of the

Skip to Step 9.

 

 

camera and to a 10/100/BaseT router or switch.

 

 

 

 

 

 

 

Step 8

If you are using the IP camera on a network connection

First, connect the bare wires at the end of the power

 

 

that does not provide PoE, connect the optional 12 VDC

adapter to the terminal block that is provided with the IP

 

 

or 24 VAC power adapter.

camera:

 

 

 

 

• With the screws on the terminal block facing down,

 

 

 

 

take either of these actions:

 

 

 

 

– For a 12 VDC power adapter—Put the positive

 

 

 

 

wire into the slot at the right rear of the terminal

 

 

 

 

block, put the negative wire into the middle slot

 

 

 

 

and put the ground wire in the left slot. (On the

 

 

 

 

Cisco power adapters, the positive wire has a

 

 

 

 

white stripe and the negative wire has no stripe.)

 

 

 

 

– For a 24 VAC power adapter—Put one wire into

 

 

 

 

the into the slot at the right rear of the terminal

 

 

 

 

block and put the other wire into the middle slot.

 

 

 

 

There is polarity, so either wire can go into either

 

 

 

 

slot.

 

 

 

 

• Use a small flat-head screwdriver to tighten the

 

 

 

 

screws on the bottom of the terminal block so that the

 

 

 

 

power adapter wires are attached securely.

 

 

 

 

Note The power adapter may include an attached

 

 

 

 

terminal block that does not fit the IP camera. If

 

 

 

 

so, remove that terminal block and replace it with

 

 

 

 

the one that is provided with the IP camera.

 

 

 

 

Next, plug the terminal block into the power input port on

 

 

 

 

back of the IP camera. The terminal block fits into the

 

 

 

 

input port in one way. Make sure that the tabs on the

 

 

 

 

terminal block face the bottom of the IP camera.

 

 

 

 

Finally, plug the power adapter into an electrical outlet.

 

 

 

 

The IP camera powers up.

 

 

 

 

 

 

 

 

Cisco Video Surveillance 4300E and 4500E High-Definition IP Camera User Guide

 

 

 

 

 

 

 

 

 

 

2-4

 

 

OL-25230-02

 

 

 

 

 

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Americas Headquarters Text Part Number OL-25230-02Copyright 2009-2011 Cisco Systems, Inc. All rights reserved N T E N T S Log Windows Overview OrganizationOL-25230-02 IP Camera Features OverviewOverview IP Camera Features Adjusting Back Focus on the IP Camera section on IP Camera Physical DetailsRear of IP Camera Described in the Resetting the IP Camera section on Side of IP CameraDC Auto Iris Lens Connector Pinouts Package ContentsInstalling the IP Camera Getting StartedAction Explanation Action Explanation OL-25230-02 Procedure Performing the Initial Setup of the IP CameraBefore you Begin Accessing the IP Camera Protocol//ipaddressHttps//192.168.0.100 Https//203.70.212.521024Http//203.70.212.52 Http//203.70.212.521024IP Camera Window Links Understanding the IP Camera User InterfaceLink Description IP Camera Windows Field DescriptionGeneral Information Network StatusAdjusting Back Focus on the IP Camera Channel 1 and ChannelPowering the IP Camera On or Off Resetting the IP CameraReset Type Procedure Remarks Managing the Local StorageFormatting the USB Flash Drive Click the Video Surveillance IP Camera Utility linkDownloading Encrypted Video Files from the USB Flash Drive Deleting Encrypted Video Files from the USB Flash DriveClick Format USB What to Do NextDecrypting Encrypted Video Files Configuring and Managing the IP Camera Accessing Navigating the Configuration WindowsFeature Setup Windows SnmpResolution Primary fps Secondary fps Streaming Settings WindowStreaming Option Description Streaming Setup AreaCurrent Channel Area Video Area Analog Video Area Camera Settings WindowAudio Area Video Adjustments Area Microphone AreaDescribed in , Viewing Live Video Day Night Filter AreaVideo Overlay Video Overlay Settings WindowText Overlay Area Input Ports Area IO Ports Settings WindowOutput Ports RS-232 Settings Pan Tilt Settings WindowPan/Tilt Area Event Notification Window Event Triggering Area Event Scheduling Area UndoSet All button Clear All buttonEmail Notification Area FTP Notification Area Patrol Sequence Window Patrol Sequence Area Basic Settings Window Network Setup WindowsAnalytics Windows IP Addressing Window Basic Settings AreaBasic Device Operations Area Time Settings Window IP Addressing AreaSet Time Mode Area You click Save SettingsLocal Time Area Clone PC Time buttonDiscovery Settings Window NTP Server Settings AreaCisco Discovery Protocol CDP Area Show Neighbors buttonSnmp v2c Area Snmp Settings WindowSnmp v3 Area 8000000901IPv4addresshex 802.1x Settings Window EAP-PEAP Configuration Options IP Filter Settings WindowEAP-FAST Configuration Options QoS Settings Window Class of Service CoS AreaIP Filter Area Filter Entries AreaDifferentiated Services DiffServ Area Administration WindowsAccount Initialization Window Access Protocols Area Administrator Accounts AreaSSH User Settings Window User List AreaChange button Maintenance Settings WindowDelete button Factory Default Area Restore button Reset buttonReboot Area Reboot button Device Configuration AreaAddressing Window section on Firmware Settings WindowDevice Information Area Firmware Maintenance Area Upgrade buttonDevice Processes Window Details buttonLog Setup Settings Window, Local Log Window, Password Complexity WindowLog Windows Local Log Settings Area Log Setup Settings WindowSyslog Settings Area Option Description Log List Area Local Log WindowLog messages, see -25 on Authenticationfailed AuthorizationfailedExplanation Severity CodeclostConfigsavefailed ConfigsavedConfiguploadfailed ConfiguploadedInputtworeset LoginOutputonereset OutputtworesetTimedstswitch TimeregswitchServercontacted ServerlostControl Description Video controlsStreaming Settings Window section on Video image controlsImage tools Hotspot Zoom button Hotspot Pan/TiltSave Snapshot button Mirror buttonFull Screen button Audio controlsPresets controls Set Current Preset asAdd Preset Position Preset buttonPan/tilt speed controls Motion detectionMotion detection controls Enable Motion Detection check box Save Settings button Full Screen checkTroubleshooting Troubleshooting Numerics IN-2 Http HttpsSee also video LEDIN-5 IN-6 IN-7 IN-8
Related manuals
Manual 86 pages 63.52 Kb

4300E specifications

The Cisco Systems 4300E Series is an advanced integrated service router designed to deliver high-performance, scalable, and secure networking solutions for enterprises. This versatile platform caters to a wide range of applications while ensuring reliability and flexibility in dynamic environments.

One of the standout features of the Cisco 4300E is its modular architecture, which allows organizations to tailor the router to their specific needs by adding or changing modules. This modularity is crucial for enterprises that require agility to adapt to evolving network demands. The router supports various network interface modules (NIMs), service modules (SMs), and high-speed WAN interface cards (HWICs), enabling seamless integration of various interfaces and features.

The Cisco 4300E is designed with performance in mind, capable of delivering high throughput and low latency, which is essential for applications such as voice, video, and data traffic. It supports robust performance with the capability of handling up to 2 Gbps of throughput, making it suitable for mid-sized to large enterprise branch offices.

Another key technology associated with the 4300E is Cisco’s Unified Communications and Collaboration suite. This integration facilitates voice, video, and messaging services across the network, ensuring efficient communication within organizations. Security features include advanced threat protection through Cisco’s integrated security services, such as firewall capabilities, VPN support, and intrusion prevention, ensuring that sensitive data remains secure.

The Cisco 4300E also supports Cisco’s DNA (Digital Network Architecture) capabilities, allowing for automation, analytics, and enhanced network visibility. This integration empowers network administrators to manage their infrastructure proactively, ensuring optimal performance and quick resolution of issues.

Additionally, the router is equipped with enhanced Quality of Service (QoS) capabilities, enabling prioritization of critical applications and traffic types. This feature is vital for maintaining high performance across diverse application requirements.

In conclusion, the Cisco 4300E Series routers stand out for their modular architecture, high performance, integrated security, and support for advanced networking technologies. These characteristics make them ideal for enterprises seeking a robust, flexible, and secure solution to meet their networking needs in an ever-evolving digital landscape. With the ability to seamlessly integrate various services and applications, the 4300E is a reliable choice for any organization looking to future-proof its network infrastructure.
Top Page Image Contents