Desa (V)V36EN-B, (V)V36EP-B Fireplace Installation, High Altitude Installation, Check GAS Type

Venting Installation

instructions

Continued

High Altitude Installation

Your DESAdirect-vent fireplace has been CSAtested and approved for elevations from 0-2000 feet (USA) and elevations from 0-4500 feet (Canada).

When installing this fireplace at an elevation above 2000 feet (in the USA), you may need to decrease the input rating by changing the existing burner orifice to a smaller size. Reduce input 4% for each 1000 feet above sea level. Check with your local gas company for proper orifice size identification.

When installing this fireplace at an elevation above 4500 feet (in Canada), check with local authorities.

Consult your local gas company to help determine the proper orifice for your location.

For assistance with any high altitude installation contact DESA Customer Service Department at 1-866-672-6040.

Parts lists for venting kits and components

DESA Pipe & Vent Kits

Number Description

P58-6 6" Section Double Wall Pipe - Galvanized

P58-12 12" Section Double Wall Pipe - Galvanized P58-24 24" Section Double Wall Pipe - Galvanized P58-36 36" Section Double Wall Pipe - Galvanized P58-48 48" Section Double Wall Pipe - Galvanized PA58-712 Adjustable 7"-12" Section Coaxial Pipe - Galvanized

FPA58-6 6" Duravent Collar to FMI Pipe Adaptor (6" Collar/Pipe Section)

DPA58-6 6" FMI Collar to Pipe Duravent Adaptor (6" Collar/Pipe Section

E58-45 45° Elbow, Galvanized

E58-90 90° Elbow, Galvanized

FSE58-45 45° Starter Elbow, Galvanized (Duravent Collar to FMI Pipe)

DSE58-45 45° Starter Elbow, Galvanized (FMI Collar to Duravent Pipe)

VKG-58 Ground Floor Vent Kit - Galvanized VKB-58 Basement Vent Kit - Galvanized VKS-58 Snorkel Kit - Galvanized VKR-58 Roof Vent Kit - Galvanized VKC-58 Corner Vent Kit - Galvanized

HTK Horizontal Round Termination Kit

HT-58 Horizontal Round Termination Kit, Galvanized HTKS-58 Horizontal Square Termination Kit

HTS-58 Horizontal Square Termination Kit, Galvanized

VT-58 Vertical Round Termination, Galvanized ST-58-14 14" Snorkel Termination, Galvanized

Number	Description
ST-58-36	36" Snorkel Termination, Galvanized
SC-58	Storm Collar - Galvanized
WF-58	Wall Firestop - Galvanized
RF-58-6	Roof Flashing - 0 to 6/12 Pitch - Galvanized
RF-58-12	Roof Flashing - 6/12 to 12/12 Pitch - Galvanized
VR-58	Vertical Restrictor - Galvanized
S-58	Vinyl Siding Standoff - Galvanized
WS-58	Wall Strap
CS-58	Cathedral Ceiling Support
FP-58	Firestop Plate
SF-58	Stucco Flashing - For use with HTS-5

Fireplace Installation

CHECK GAS TYPE

Use proper gas type for the fireplace unit you are installing. If you have conflicting gas types, do not install fireplace. See retailer where you purchased the fireplace for proper fireplace according to your gas type.

Installing optional blower accessories

NOTICE: If installing blower in an existing fireplace with gas connections, shut off gas supply and disconnect heater from gas supply. Contact a qualified service person to do this.

WARNING: If there is a duplex electrical outlet in- stalled in the right side of the bottom of the fireplace base area, be sure that the electrical power to the outlet is turned off before proceeding with blower installation. Failure to do this may result in serious injury.

Model BK Installation

Follow all instructions provided in the blower accessory kit.

1.Attach the power cord to the blower motor by firmly pushing the two female terminals at the end of the power cord onto the two spade terminals on the blower motor (see Figure 25).

		Blower
		Location
	Lower Firebox
	Cavity
Side View	Spade
		Magnetic
	Terminals
		Strips

Exhaust

Port

Green

Ground Wire

Screw

Figure 25 - Blower Model BK

14 www.desatech.com 111253-01F