OPERATING FIREPLACE
Continued
D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.
LIGHTING
INSTRUCTIONS
1.STOP! Read the safety information above before proceeding.
2.Set the
3.Turn off all electrical power to the appliance.
4.Open control access panel.
5.Push in gas control knob slightly and turn
clockwise 
to “OFF”.
6.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If you donʼt smell gas, go to the next step.
7.The pilot is located by the main burner.
8.Turn knob on gas control counterclockwise 
to “PILOT”.
9.Push in the control knob all the way and hold in. Immediately light the pilot by pressing the red ignitor button until a flame appears. Con- tinue to hold the control knob in for about one
(1)minute after the pilot is lit. Release knob and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 5 through 9.
• If knob does not pop out when released, stop and call service technician or gas supplier.
• If the pilot will not stay lit after several tries, turn gas control knob to “OFF” and call your service technician or gas supplier.
10.Turn gas control knob counterclockwise 
to “ON”. Knob can be turned to “ON” only if the control knob is popped out.
11.Set “HI-LO” knob to desired setting.
12.Turn on all electric power to the appliance. Note: It is recommended that you maintain the gas control knob in the full OFF position during lengthy periods of seasonal
Position |
|
Indicator |
|
Gas Control |
|
Knob | HI/LO Knob |
Figure 32 - Control Knob in Pilot Position
|
| Piezo | Pilot Burner | |||||
Thermocouple Ignitor |
|
| Thermopile | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 33 - Pilot
TO TURN OFF GAS
TO APPLIANCE
1.Turn off the wall switch.
2.Turn off all electric power to the appliance if service is to be performed.
3.Remove control access panel.
4.Push in gas control knob slightly and turn
clockwise 
to “OFF”. Do not force.
5.Replace control access panel.
CONVERTING FIREPLACE FROM NATURAL GAS TO PROPANE/LP GAS
The conversion kit is packaged with the unit. Please check the contents before beginning this conversion.
WARNING: Before proceed- ing, make sure the gas control valve is in the OFF position and all electrical power to the appli- ance is turned off.
CONVERTING PILOT
1.Wait five (5) minutes to clear out any gas. Smell for any gas odor, especially near the floor. If any gas odor is present, STOP! See For Your Safety Read Before Lighting on page 14.
2.Locate the latch on the louver assembly. Remove top and bottom louvers by pulling the spring latches toward the center of the fireplace simultaneously until they are disen- gaged from the locating holes.
3.Undo latches located on top and bottom of fire- box and swing door to the fully open position.
4.Carefully remove log set and ember material from burner and place them aside in a safe place.
5.Replace main burner orifice with burner orifice included in conversion kit (Model
www.desatech.com | 15 |