Country Flame FP42, FP37, Fireplace FP33 manual Blower Installations

Page 24

that this block is centered on the edge of the angle iron and maintains a distance of ½ inch from the clay flue tile face. Once the clay flue tile and first course of brick are checked and verified for proper installation, proper level, and proper clearances, each successive clay flue tile, and courses of chimney brick can be added until the chimney cap height is reached. Check local building code for specifics on masonry chimney installations. For those in earthquake prone areas, ensure that local seismic requirements are met when building a masonry chimney. FIGURE 7B is provided to show the proper positioning of chimney brick from the clay flue tile and position on the top edge of the angle iron.

Both masonry and factory-build chimneys must extend at least three feet above a point where the chimney passes through any roof. A chimney must also be at least two feet above any part of the building or roofline within ten feet of a horizontal radius around the chimney structure. A taller chimney may be required under certain site specific conditions for adequate draft. Good draft is normally achieved with chimney heights at least fifteen feet high measured from the top of the fireplace opening to the top of the chimney. A chimney must be capped to resist water penetration. A mortar wash that is feathered to the edge of the chimney wall is not an adequate cap. The chimney cap should be cast-in-place or pre-cast concrete. Check with a builder, masonry chimney installer and always consult local codes to ensure proper chimney installation.

STEP 6 – BLOWER INSTALLATIONS

Blowers add to the efficiency of the Smart Fireplace Furnace by moving room air across the heat exchanger fins built into the Smart Fireplace Furnace. This air is heated and then returned to the room or home duct system to provide more uniform heating throughout the house. Country Flame provides two grille frames that are to be framed in by the mason when finishing the front face of the Smart Fireplace Furnace. FIGURE 8A shows how a blower is

mounted to the Smart Fireplace. Figure 8B shows the proper installation of the air intake grills with variable speed controls attached. Follow the steps listed below to install each blower. Refer to FIGURE 12 for the electrical schematic of the blower system.

FIGURE 8A: BLOWER INSTALLATION

Version 7.1

13

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Installation,Operation MaintenanceManual Installation, Operation & Maintenance Manual Table of Contents Version Iii Please keep a copy for your personal records Date Purchased Model No# Serial No# Installed By Trained By Foreword Safety Notes Version Viii Fireplace Furnace Safety Label PP-741 Chimney SizeIntroduction Country Flame Technologies1Chapter WHAT’S Included with Your Smart FIREPLACE?Fireplace Furnace Specifications ModelFireplace Dimensions Steps to Install a Smart Fireplace Footings and FoundationsSingle Opening Fireplace Systems Outside Wall PAD Installation Concrete PAD & Hearth ExtensionsInside Wall PAD Installation Fireplace Position on the Concrete PAD Fireplace Wall & Chimney ConstructionChimney Flue Installation Masonry Wall InstallationTypical HT Adapter optional Installation Model No Angle Iron Duct Size Flue Size Height Depth Masonry Chimney Installation Blower Installations Blower InstallationAIR Intake Grille Installation Heat Discharge Boot Completion of Masonry Brick Front Flue Damper Control Installation Damper PartsDamper Door Removal Damper Door Control Electrical System Thermal Snap Disk LocationElectrical System Version 2Chapter Ducting OptionsDucting Systems Examples Ducting Systems Examples Fireplace Furnace Operational Requirements Internal Thermostat Wood Fireplace Furnace Maintenance Requirements 4ChapterOutside Combustion AIR Troubleshooting Guide Problem Cause SolutionCombustion. Open your draft controls for up Replacement Parts Replacement Parts cont’d Part Drawings Ceramic Snap DISK, PP-91 THERMOSTAT, PP-563 Insulation for TOP, SIDES, FRONT, and BACK, PP-35 ASH Dump COVER, FP-0000-916 Yoke Bracket ASSEMBLY, FP-0000-923 Damper ROD ASSEMBLY, FP-0000-920 FP-33 & FP-37 Flue to HT Chimney ADAPTER, F-218 Grille BACK, FP-0000-33 Grille FRONT, FP-0000-32 AIR Intake GRILLE, PP-560 Adjustable Heat Discharge Boot OPTIONAL, FP-0000-925 LOG Grate optional, LG-900 Company Label Grate Warning Label Country Flame Technologies Required Warranty Information

Fireplace FP33, FP42, FP37 specifications

The Country Flame FP37, FP33, and FP42 fireplaces represent the pinnacle of modern heating technology, with each model expertly designed to meet the diverse demands of homeowners. These fireplaces offer not only warmth but also an aesthetic flair that enhances any living space.

The FP37 is renowned for its substantial heat output, making it an ideal option for larger areas. With a heating capacity of up to 2,800 square feet, it incorporates advanced combustion technology that ensures efficient fuel consumption while maximizing heat production. The innovative air wash system keeps the glass pane clear, providing a spectacular view of the dancing flames. Its multi-fuel capability allows users to burn wood, coal, or pellets, providing flexibility and convenience based on individual preferences.

In contrast, the FP33 is designed for smaller spaces without sacrificing performance. This compact model is capable of heating areas up to 2,000 square feet. Its efficient design promotes quick and easy installation, making it a favorite among homeowners looking for an effective heating solution with a smaller footprint. The FP33 features an adjustable firebox, enabling users to control the intensity of the flames and the heat output according to their needs, ensuring a cozy environment throughout the chilly months.

Meanwhile, the FP42 is a robust option for those seeking a powerful heating source. With a capacity to heat spaces exceeding 3,000 square feet, it features a larger firebox allowing for longer burn times and reduced refueling frequency. Like its counterparts, the FP42 employs a state-of-the-art catalytic converter that enhances burn efficiency and reduces harmful emissions, making it an environmentally responsible choice for heating.

All three models prioritize user-friendliness, with easy-to-use controls and straightforward maintenance. Their durable construction, designed to withstand high temperatures, ensures longevity and reliability. Additionally, all Country Flame fireplaces are backed by an industry-leading warranty, providing peace of mind for owners.

With sleek designs and a variety of options to suit different aesthetics, Country Flame FP37, FP33, and FP42 fireplaces truly embody the blend of functionality and beauty. Whether for a cozy living room or a spacious family area, these fireplaces guarantee a warm and inviting atmosphere, making them an exquisite addition to any home. Choosing any of these models means investing in quality warmth and unmatched comfort for years to come.
Top Page Image Contents