Country Flame Fireplace FP33, FP42, FP37 manual Damper Door Removal

Page 29

INSTALLING DAMPER DOOR - The rotary controlled damper of your Country Flame Fireplace should be assembled as shown in FIGURE 10 after the fireplace is completely installed. At this time the adjustable damper rod sleeve (C) will be embedded in the masonry veneer and cannot turn. Follow the steps below to complete the installation of

your rotary controlled damper.

1.Begin with the damper door (G) in the fully open position. Insert the damper rod (D) through the adjustable damper rod sleeve (C) from the front of the fireplace.

2.From inside the fireplace guide the washer (J) over the end of the damper rod (D).

3.Reach inside the fireplace and slide the damper screw (E) over the end of the damper rod (D) with the setscrew opening positioned toward the rear of the fireplace.

4.Push the damper rod (D) as far toward the rear of the fireplace as possible. Push the damper screw (E) as far to the front of the fireplace as possible.

5.Mark the damper rod (D) flush with the end of the damper screw (E).

6.Remove the assembly and cut the damper rod (D) off at the mark you made in Step 5.

7.Replace the assembly as in Steps 1 and 2.

8.Insert the damper screw (E) into the damper screw bracket (F) and turn it completely counter clockwise until it seats.

9.Slide the end of the damper screw (E) without the setscrew opening over the end of the damper rod (D) and push both the damper screw (E) and the damper rod (D) toward each other as far as possible.

10.Tighten the setscrew (B) at the back of the damper screw (E).

11.Install the logo handle (A) on the outer end of the damper rod (D), align properly, and tighten the setscrew (B).

NOTE: Always close the damper door when the fireplace is not in use. Closing the damper door during non use periods will prevent airflow into or out of the house thus conserving energy whatever the season may be.

FIGURE 11a: DAMPER DOOR REMOVAL

REMOVING DAMPER DOOR - The rotary controlled damper of your Country Flame Fireplace can be removed if necessary. Whether for fireplace system cleaning or repair, follow the steps listed below to remove the damper. FIGURE 11a can be referenced when

it is necessary to remove the damper door.

Version 7.1

18

 

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Installation,Operation MaintenanceManual Installation, Operation & Maintenance Manual Table of Contents Version Iii Please keep a copy for your personal records Date Purchased Model No# Serial No# Installed By Trained By Foreword Safety Notes Version Viii Chimney Size Fireplace Furnace Safety Label PP-741Country Flame Technologies IntroductionWHAT’S Included with Your Smart FIREPLACE? 1ChapterModel Fireplace Furnace SpecificationsFireplace Dimensions Footings and Foundations Steps to Install a Smart FireplaceSingle Opening Fireplace Systems Concrete PAD & Hearth Extensions Outside Wall PAD InstallationInside Wall PAD Installation Fireplace Wall & Chimney Construction Fireplace Position on the Concrete PADMasonry Wall Installation Chimney Flue InstallationTypical HT Adapter optional Installation Model No Angle Iron Duct Size Flue Size Height Depth Masonry Chimney Installation Blower Installation Blower InstallationsAIR Intake Grille Installation Heat Discharge Boot Completion of Masonry Brick Front Damper Parts Flue Damper Control InstallationDamper Door Removal Damper Door Control Thermal Snap Disk Location Electrical SystemElectrical System Version Ducting Options 2ChapterDucting Systems Examples Ducting Systems Examples Fireplace Furnace Operational Requirements Internal Thermostat Wood 4Chapter Fireplace Furnace Maintenance RequirementsOutside Combustion AIR Problem Cause Solution Troubleshooting GuideCombustion. Open your draft controls for up Replacement Parts Replacement Parts cont’d Part Drawings Ceramic Snap DISK, PP-91 THERMOSTAT, PP-563 Insulation for TOP, SIDES, FRONT, and BACK, PP-35 ASH Dump COVER, FP-0000-916 Yoke Bracket ASSEMBLY, FP-0000-923 Damper ROD ASSEMBLY, FP-0000-920 FP-33 & FP-37 Flue to HT Chimney ADAPTER, F-218 Grille BACK, FP-0000-33 Grille FRONT, FP-0000-32 AIR Intake GRILLE, PP-560 Adjustable Heat Discharge Boot OPTIONAL, FP-0000-925 LOG Grate optional, LG-900 Company Label Grate Warning Label Country Flame Technologies Required Warranty Information

Fireplace FP33, FP42, FP37 specifications

The Country Flame FP37, FP33, and FP42 fireplaces represent the pinnacle of modern heating technology, with each model expertly designed to meet the diverse demands of homeowners. These fireplaces offer not only warmth but also an aesthetic flair that enhances any living space.

The FP37 is renowned for its substantial heat output, making it an ideal option for larger areas. With a heating capacity of up to 2,800 square feet, it incorporates advanced combustion technology that ensures efficient fuel consumption while maximizing heat production. The innovative air wash system keeps the glass pane clear, providing a spectacular view of the dancing flames. Its multi-fuel capability allows users to burn wood, coal, or pellets, providing flexibility and convenience based on individual preferences.

In contrast, the FP33 is designed for smaller spaces without sacrificing performance. This compact model is capable of heating areas up to 2,000 square feet. Its efficient design promotes quick and easy installation, making it a favorite among homeowners looking for an effective heating solution with a smaller footprint. The FP33 features an adjustable firebox, enabling users to control the intensity of the flames and the heat output according to their needs, ensuring a cozy environment throughout the chilly months.

Meanwhile, the FP42 is a robust option for those seeking a powerful heating source. With a capacity to heat spaces exceeding 3,000 square feet, it features a larger firebox allowing for longer burn times and reduced refueling frequency. Like its counterparts, the FP42 employs a state-of-the-art catalytic converter that enhances burn efficiency and reduces harmful emissions, making it an environmentally responsible choice for heating.

All three models prioritize user-friendliness, with easy-to-use controls and straightforward maintenance. Their durable construction, designed to withstand high temperatures, ensures longevity and reliability. Additionally, all Country Flame fireplaces are backed by an industry-leading warranty, providing peace of mind for owners.

With sleek designs and a variety of options to suit different aesthetics, Country Flame FP37, FP33, and FP42 fireplaces truly embody the blend of functionality and beauty. Whether for a cozy living room or a spacious family area, these fireplaces guarantee a warm and inviting atmosphere, making them an exquisite addition to any home. Choosing any of these models means investing in quality warmth and unmatched comfort for years to come.
Top Page Image Contents