Country Flame FP37, FP42, Fireplace FP33 manual Fireplace Furnace Operational Requirements

Page 37

Chapter3

FIREPLACE FURNACE OPERATIONAL REQUIREMENTS

Immediately after your Country Flame Fireplace has been properly installed it should be tested for draft. A draft test is a simple method used to ensure air is moving up the chimney (positive air flow versus a house that may have negative pressure.) Wad up one or two sheets of clean dry newspaper. Set this paper in the middle of the firebox. Ensure that the rotary control damper is

turned fully open (clockwise). If the fireplace furnace is equipped with fireplace doors (optional), open the door’s draft controls. If the chimney system is drawing properly, smoke from this burning newspaper and the paper’s flames should be drawn up and into the open flue. If on the other hand, the smoke blows into the room or burns very slowly, either there is negative pressure in the house or the existing chimney system is not operating properly. Have the system checked by a qualified chimney sweep or certified contractor or contact a Country Flame dealer.

Things that should be checked in case of poor draft:

•Make sure the chimney flue damper is completely open. (Rotated clockwise)

•See that the flue is clear of obstructions such as debris, creosote, nests, etc.

•If chimney flue has chimney cap, remove it and make sure it is clean.

•The chimney flue may not extend high enough above the roof or it may be obstructed.

•The chimney system may have leaks substantial enough to reduce the draw.

After checking the installation for proper draft, you are ready to build your first fire. The first fire should be relatively light. This breaks in the heater slowly, rather than the sometimes-damaging effect of a flash fire in the initial firing. For this first firing we suggest the following procedure:

Step 1 During the first firing of your Country Flame Fireplace, and anytime it is refired in the future; the rotary control damper should be turned completely clockwise in the fully open position. This allows for maximum draft.

Step 2 Place several pieces of wadded-up newspaper in the forward section of your Country Flame heater directly on top of the grates.

Step 3 Directly on top of the newspaper; place a good size bundle of lighter wood, rolled-up newspaper or small kindling.

Version 7.1

26

 

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Installation,Operation MaintenanceManual Installation, Operation & Maintenance Manual Table of Contents Version Iii Please keep a copy for your personal records Date Purchased Model No# Serial No# Installed By Trained By Foreword Safety Notes Version Viii Chimney Size Fireplace Furnace Safety Label PP-741Country Flame Technologies IntroductionWHAT’S Included with Your Smart FIREPLACE? 1ChapterModel Fireplace Furnace SpecificationsFireplace Dimensions Footings and Foundations Steps to Install a Smart FireplaceSingle Opening Fireplace Systems Concrete PAD & Hearth Extensions Outside Wall PAD InstallationInside Wall PAD Installation Fireplace Wall & Chimney Construction Fireplace Position on the Concrete PADMasonry Wall Installation Chimney Flue InstallationTypical HT Adapter optional Installation Model No Angle Iron Duct Size Flue Size Height Depth Masonry Chimney Installation Blower Installation Blower InstallationsAIR Intake Grille Installation Heat Discharge Boot Completion of Masonry Brick Front Damper Parts Flue Damper Control InstallationDamper Door Removal Damper Door Control Thermal Snap Disk Location Electrical SystemElectrical System Version Ducting Options 2ChapterDucting Systems Examples Ducting Systems Examples Fireplace Furnace Operational Requirements Internal Thermostat Wood 4Chapter Fireplace Furnace Maintenance RequirementsOutside Combustion AIR Problem Cause Solution Troubleshooting GuideCombustion. Open your draft controls for up Replacement Parts Replacement Parts cont’d Part Drawings Ceramic Snap DISK, PP-91 THERMOSTAT, PP-563 Insulation for TOP, SIDES, FRONT, and BACK, PP-35 ASH Dump COVER, FP-0000-916 Yoke Bracket ASSEMBLY, FP-0000-923 Damper ROD ASSEMBLY, FP-0000-920 FP-33 & FP-37 Flue to HT Chimney ADAPTER, F-218 Grille BACK, FP-0000-33 Grille FRONT, FP-0000-32 AIR Intake GRILLE, PP-560 Adjustable Heat Discharge Boot OPTIONAL, FP-0000-925 LOG Grate optional, LG-900 Company Label Grate Warning Label Country Flame Technologies Required Warranty Information

Fireplace FP33, FP42, FP37 specifications

The Country Flame FP37, FP33, and FP42 fireplaces represent the pinnacle of modern heating technology, with each model expertly designed to meet the diverse demands of homeowners. These fireplaces offer not only warmth but also an aesthetic flair that enhances any living space.

The FP37 is renowned for its substantial heat output, making it an ideal option for larger areas. With a heating capacity of up to 2,800 square feet, it incorporates advanced combustion technology that ensures efficient fuel consumption while maximizing heat production. The innovative air wash system keeps the glass pane clear, providing a spectacular view of the dancing flames. Its multi-fuel capability allows users to burn wood, coal, or pellets, providing flexibility and convenience based on individual preferences.

In contrast, the FP33 is designed for smaller spaces without sacrificing performance. This compact model is capable of heating areas up to 2,000 square feet. Its efficient design promotes quick and easy installation, making it a favorite among homeowners looking for an effective heating solution with a smaller footprint. The FP33 features an adjustable firebox, enabling users to control the intensity of the flames and the heat output according to their needs, ensuring a cozy environment throughout the chilly months.

Meanwhile, the FP42 is a robust option for those seeking a powerful heating source. With a capacity to heat spaces exceeding 3,000 square feet, it features a larger firebox allowing for longer burn times and reduced refueling frequency. Like its counterparts, the FP42 employs a state-of-the-art catalytic converter that enhances burn efficiency and reduces harmful emissions, making it an environmentally responsible choice for heating.

All three models prioritize user-friendliness, with easy-to-use controls and straightforward maintenance. Their durable construction, designed to withstand high temperatures, ensures longevity and reliability. Additionally, all Country Flame fireplaces are backed by an industry-leading warranty, providing peace of mind for owners.

With sleek designs and a variety of options to suit different aesthetics, Country Flame FP37, FP33, and FP42 fireplaces truly embody the blend of functionality and beauty. Whether for a cozy living room or a spacious family area, these fireplaces guarantee a warm and inviting atmosphere, making them an exquisite addition to any home. Choosing any of these models means investing in quality warmth and unmatched comfort for years to come.
Top Page Image Contents