Country Flame FP42, FP37, Fireplace FP33 manual Version Viii

Page 9

15.Due to high temperatures, the fireplace furnace should be located out of traffic and away from furniture and draperies.

16.Clothing or other flammable material should not be placed on or near the fireplace furnace.

17.When disposing of ash accumulations from a fireplace, always place them in a metal container with a tight fitting lid. The closed container must be placed on a non-combustible surface well away from all combustible materials, pending final disposal. The ashes should be retained in the closed container until all cinders have thoroughly cooled.

18.Safety screens, doors, or guards removed for maintenance must be replaced prior to operation.

19.In accordance with the Uniform Building Code, this fireplace is designed for installation in a masonry fireplace hull designed for burning wood fuel. Failure to comply with restrictions voids all warranties and violates the safety listing of the unit. Poor quality fuel directly (and adversely) affects efficiency and cleanliness of operation. A Country Flame Dealer can provide advice on the proper fuel choice for your area.

20.NEVER use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this heater. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

21.INSTALL a smoke detector within the proximity of the Smart Fireplace Furnace.

22.NEVER put foreign objects or burn unapproved material in the Smart Fireplace Furnace.

23.NEVER block free airflow through open vents connected to the Smart Fireplace Furnace.

24.Chimney systems need to be checked twice a year (minimum) for soot or creosote buildup. An improperly installed and maintained Smart Fireplace Furnace can cause home fires.

25.If optional fireplace doors are installed and closed, in the event of an extended power outage, the combustion air opening of the fireplace door system must be opened at least one turn.

26.Maximum static pressure in fireplace furnace ductwork is one-quarter inch of water column.

27.If heated air from the Smart Fireplace Furnace is to be connected into the home central duct system, the connection can only be on the air outlet side of the gas furnace.

28.If the Smart Fireplace Furnace is connected to the home central furnace system, care must be taken NOT to violate any home central furnace manufacturer’s specified operating conditions.

29.The Smart Fireplace Furnace must incorporate a “Y” configuration connection from the fireplace ductwork to the central duct system.

30.ALWAYS use a log grate or andiron while burning a fire. See warning label for more details.

Version 7.1

viii

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Installation,Operation MaintenanceManual Installation, Operation & Maintenance Manual Table of Contents Version Iii Please keep a copy for your personal records Date Purchased Model No# Serial No# Installed By Trained By Foreword Safety Notes Version Viii Chimney Size Fireplace Furnace Safety Label PP-741Country Flame Technologies IntroductionWHAT’S Included with Your Smart FIREPLACE? 1ChapterModel Fireplace Furnace SpecificationsFireplace Dimensions Footings and Foundations Steps to Install a Smart FireplaceSingle Opening Fireplace Systems Concrete PAD & Hearth Extensions Outside Wall PAD InstallationInside Wall PAD Installation Fireplace Wall & Chimney Construction Fireplace Position on the Concrete PADMasonry Wall Installation Chimney Flue InstallationTypical HT Adapter optional Installation Model No Angle Iron Duct Size Flue Size Height Depth Masonry Chimney Installation Blower Installation Blower InstallationsAIR Intake Grille Installation Heat Discharge Boot Completion of Masonry Brick Front Damper Parts Flue Damper Control InstallationDamper Door Removal Damper Door Control Thermal Snap Disk Location Electrical SystemElectrical System Version Ducting Options 2ChapterDucting Systems Examples Ducting Systems Examples Fireplace Furnace Operational Requirements Internal Thermostat Wood 4Chapter Fireplace Furnace Maintenance RequirementsOutside Combustion AIR Problem Cause Solution Troubleshooting GuideCombustion. Open your draft controls for up Replacement Parts Replacement Parts cont’d Part Drawings Ceramic Snap DISK, PP-91 THERMOSTAT, PP-563 Insulation for TOP, SIDES, FRONT, and BACK, PP-35 ASH Dump COVER, FP-0000-916 Yoke Bracket ASSEMBLY, FP-0000-923 Damper ROD ASSEMBLY, FP-0000-920 FP-33 & FP-37 Flue to HT Chimney ADAPTER, F-218 Grille BACK, FP-0000-33 Grille FRONT, FP-0000-32 AIR Intake GRILLE, PP-560 Adjustable Heat Discharge Boot OPTIONAL, FP-0000-925 LOG Grate optional, LG-900 Company Label Grate Warning Label Country Flame Technologies Required Warranty Information

Fireplace FP33, FP42, FP37 specifications

The Country Flame FP37, FP33, and FP42 fireplaces represent the pinnacle of modern heating technology, with each model expertly designed to meet the diverse demands of homeowners. These fireplaces offer not only warmth but also an aesthetic flair that enhances any living space.

The FP37 is renowned for its substantial heat output, making it an ideal option for larger areas. With a heating capacity of up to 2,800 square feet, it incorporates advanced combustion technology that ensures efficient fuel consumption while maximizing heat production. The innovative air wash system keeps the glass pane clear, providing a spectacular view of the dancing flames. Its multi-fuel capability allows users to burn wood, coal, or pellets, providing flexibility and convenience based on individual preferences.

In contrast, the FP33 is designed for smaller spaces without sacrificing performance. This compact model is capable of heating areas up to 2,000 square feet. Its efficient design promotes quick and easy installation, making it a favorite among homeowners looking for an effective heating solution with a smaller footprint. The FP33 features an adjustable firebox, enabling users to control the intensity of the flames and the heat output according to their needs, ensuring a cozy environment throughout the chilly months.

Meanwhile, the FP42 is a robust option for those seeking a powerful heating source. With a capacity to heat spaces exceeding 3,000 square feet, it features a larger firebox allowing for longer burn times and reduced refueling frequency. Like its counterparts, the FP42 employs a state-of-the-art catalytic converter that enhances burn efficiency and reduces harmful emissions, making it an environmentally responsible choice for heating.

All three models prioritize user-friendliness, with easy-to-use controls and straightforward maintenance. Their durable construction, designed to withstand high temperatures, ensures longevity and reliability. Additionally, all Country Flame fireplaces are backed by an industry-leading warranty, providing peace of mind for owners.

With sleek designs and a variety of options to suit different aesthetics, Country Flame FP37, FP33, and FP42 fireplaces truly embody the blend of functionality and beauty. Whether for a cozy living room or a spacious family area, these fireplaces guarantee a warm and inviting atmosphere, making them an exquisite addition to any home. Choosing any of these models means investing in quality warmth and unmatched comfort for years to come.
Top Page Image Contents