Country Flame Fireplace FP33, FP42, FP37 manual Internal Thermostat

Page 38

Step 4 On top of both the newspaper and the lighter wood, place two well seasoned, small- sized logs; one at the front, one directly behind it, and another small one in the middle top of the other two. A small log on the top avoids smothering the fire.

Step 5 After the fire starts to burn, leave damper open and close fireplace doors (optional), if installed. If equipped with Fireplace Doors (optional) open the door’s draft control and bring the fire to desired burn with these controls.

Step 6 Allow the fireplace to warm thoroughly and all logs to begin burning well before either adding additional wood or closing your draft controls. This will normally require fifteen minutes or longer.

Step 7 Adjust your wall thermostat to the desired setting. The blowers are equipped with speed controls to adjust airflow through the unit. These speed controls do not have an off position and can only minimize or maximize airflow by turning the speed control knob located on the front blower grille. As the fire heats up the fireplace furnace, the air discharge snap disc will close and the blowers will turn on unless the thermostat is not calling for heat. Once the fireplace furnace cools down, the thermostat or the air discharge snap disc will automatically shut the blowers off. Do not use speed controls with an “off position” as this may cause the fireplace furnace system to overheat.

Step 8 Adjust the variable speed fans to the desired speed setting by rotating the individual knobs located in the middle of the blower box grilles.

INTERNAL THERMOSTAT

The internal air discharge thermostat (snap disc) is located on the inside right of the hot air discharge grille on the front of the Smart Fireplace Furnace. This snap disc activates the fireplace blowers once the air temperature in the discharge grille rises past 110º F. This same air discharge snap disc will automatically turn off the blower systems when the discharge temperature drops below about 90º F. This snap disc, along with a wall thermostat works controls the temperature of when the blower system operates. The combination of the air discharge snap disc and the wall thermostat ensures that a specific fireplace will not blow cold air or overheat the room by continuing to blow hot air when a specific room temperature has been reached.

DISPOSAL OF ASHES

Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be placed on a noncombustible floor or on the ground, well away from any and all combustible materials, pending final disposal of the cool ashes. All ashes should be retained in the closed container until all cinders have thoroughly cooled. Ashes may also be removed through the ash dump opening.

USE OF LIQUID FUELS

Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or “freshen-up” a fire in the Country Flame fireplace furnace. Keep all such liquids or any other combustible fluids well away from the fireplace furnace while it is in use.

CREOSOTE FORMATION AND REMOVAL

When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue or a slow- burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote

Version 7.1

27

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Installation,Operation MaintenanceManual Installation, Operation & Maintenance Manual Table of Contents Version Iii Please keep a copy for your personal records Date Purchased Model No# Serial No# Installed By Trained By Foreword Safety Notes Version Viii Fireplace Furnace Safety Label PP-741 Chimney SizeIntroduction Country Flame Technologies1Chapter WHAT’S Included with Your Smart FIREPLACE?Fireplace Furnace Specifications ModelFireplace Dimensions Steps to Install a Smart Fireplace Footings and FoundationsSingle Opening Fireplace Systems Outside Wall PAD Installation Concrete PAD & Hearth ExtensionsInside Wall PAD Installation Fireplace Position on the Concrete PAD Fireplace Wall & Chimney ConstructionChimney Flue Installation Masonry Wall InstallationTypical HT Adapter optional Installation Model No Angle Iron Duct Size Flue Size Height Depth Masonry Chimney Installation Blower Installations Blower InstallationAIR Intake Grille Installation Heat Discharge Boot Completion of Masonry Brick Front Flue Damper Control Installation Damper PartsDamper Door Removal Damper Door Control Electrical System Thermal Snap Disk LocationElectrical System Version 2Chapter Ducting OptionsDucting Systems Examples Ducting Systems Examples Fireplace Furnace Operational Requirements Internal Thermostat Wood Fireplace Furnace Maintenance Requirements 4ChapterOutside Combustion AIR Troubleshooting Guide Problem Cause SolutionCombustion. Open your draft controls for up Replacement Parts Replacement Parts cont’d Part Drawings Ceramic Snap DISK, PP-91 THERMOSTAT, PP-563 Insulation for TOP, SIDES, FRONT, and BACK, PP-35 ASH Dump COVER, FP-0000-916 Yoke Bracket ASSEMBLY, FP-0000-923 Damper ROD ASSEMBLY, FP-0000-920 FP-33 & FP-37 Flue to HT Chimney ADAPTER, F-218 Grille BACK, FP-0000-33 Grille FRONT, FP-0000-32 AIR Intake GRILLE, PP-560 Adjustable Heat Discharge Boot OPTIONAL, FP-0000-925 LOG Grate optional, LG-900 Company Label Grate Warning Label Country Flame Technologies Required Warranty Information

Fireplace FP33, FP42, FP37 specifications

The Country Flame FP37, FP33, and FP42 fireplaces represent the pinnacle of modern heating technology, with each model expertly designed to meet the diverse demands of homeowners. These fireplaces offer not only warmth but also an aesthetic flair that enhances any living space.

The FP37 is renowned for its substantial heat output, making it an ideal option for larger areas. With a heating capacity of up to 2,800 square feet, it incorporates advanced combustion technology that ensures efficient fuel consumption while maximizing heat production. The innovative air wash system keeps the glass pane clear, providing a spectacular view of the dancing flames. Its multi-fuel capability allows users to burn wood, coal, or pellets, providing flexibility and convenience based on individual preferences.

In contrast, the FP33 is designed for smaller spaces without sacrificing performance. This compact model is capable of heating areas up to 2,000 square feet. Its efficient design promotes quick and easy installation, making it a favorite among homeowners looking for an effective heating solution with a smaller footprint. The FP33 features an adjustable firebox, enabling users to control the intensity of the flames and the heat output according to their needs, ensuring a cozy environment throughout the chilly months.

Meanwhile, the FP42 is a robust option for those seeking a powerful heating source. With a capacity to heat spaces exceeding 3,000 square feet, it features a larger firebox allowing for longer burn times and reduced refueling frequency. Like its counterparts, the FP42 employs a state-of-the-art catalytic converter that enhances burn efficiency and reduces harmful emissions, making it an environmentally responsible choice for heating.

All three models prioritize user-friendliness, with easy-to-use controls and straightforward maintenance. Their durable construction, designed to withstand high temperatures, ensures longevity and reliability. Additionally, all Country Flame fireplaces are backed by an industry-leading warranty, providing peace of mind for owners.

With sleek designs and a variety of options to suit different aesthetics, Country Flame FP37, FP33, and FP42 fireplaces truly embody the blend of functionality and beauty. Whether for a cozy living room or a spacious family area, these fireplaces guarantee a warm and inviting atmosphere, making them an exquisite addition to any home. Choosing any of these models means investing in quality warmth and unmatched comfort for years to come.
Top Page Image Contents