Country Flame Fireplace FP33, FP42, FP37 manual Ducting Systems Examples

Page 35

Holes in brick masonry should be a half-inch larger diameter hole than the duct pipe to be utilized. This will allow an area for expansion of the duct pipe as it heats up. Example: if ducting a Country Flame Model 33, a 6-½ inch diameter hole should be cut in the masonry for the duct: whereas, for the Model 37 and the Model 42, an 8-½ inch diameter hole should be cut in the masonry for the duct. All clearances listed in Table 1, page 2 must be strictly adhered to.

FIGURE 15 shows a side (one side only for clarity) view of the optional side vent fireplace. To order this optional side vented fireplace furnace, contact a Country Flame dealer or Country Flame direct.

FIGURE 16 provides a view of several different options that are possible for connecting fireplace furnace ducting systems. Clearly, a plan must be developed for how the ducts will be connected before installation is begun or completed. The following steps will assist in properly installing ductwork but local codes and your home’s HVAC expert should be consulted.

1.Use 26 gauge or heavier galvanized pipes for ducting. WARNING: DO NOT use plastic or flex ducting. The ductwork must be wrapped with two inches of insulation as per table 10-D of the Uniform Mechanical Code (UMC) within the masonry cavity.

2.Wrap the duct pipe for the first fifteen feet out of the masonry cavity with a minimum of two inches of insulation as per 10-D of the UMC. After fifteen feet no insulation is required but is HIGHLY RECOMMENDED in order to minimize heat loss. WARNING: Maintain a minimum clearance of at least three inches to all combustible materials over the entire length of the ductwork.

3.Ducts must have adequate straps or other means of securing the ductwork to prevent sagging or movement.

4.Do not reduce the size of the ductwork. Avoid using 90o elbows where possible. Two 45o elbows are preferable to a single 90o elbow and will minimize pressure drops within the ductwork system.

FIGURE 16a: DUCTING SYSTEMS EXAMPLES

Version 7.1

24

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Installation,Operation MaintenanceManual Installation, Operation & Maintenance Manual Table of Contents Version Iii Please keep a copy for your personal records Date Purchased Model No# Serial No# Installed By Trained By Foreword Safety Notes Version Viii Chimney Size Fireplace Furnace Safety Label PP-741Country Flame Technologies IntroductionWHAT’S Included with Your Smart FIREPLACE? 1ChapterModel Fireplace Furnace SpecificationsFireplace Dimensions Footings and Foundations Steps to Install a Smart FireplaceSingle Opening Fireplace Systems Concrete PAD & Hearth Extensions Outside Wall PAD InstallationInside Wall PAD Installation Fireplace Wall & Chimney Construction Fireplace Position on the Concrete PADMasonry Wall Installation Chimney Flue InstallationTypical HT Adapter optional Installation Model No Angle Iron Duct Size Flue Size Height Depth Masonry Chimney Installation Blower Installation Blower InstallationsAIR Intake Grille Installation Heat Discharge Boot Completion of Masonry Brick Front Damper Parts Flue Damper Control InstallationDamper Door Removal Damper Door Control Thermal Snap Disk Location Electrical SystemElectrical System Version Ducting Options 2ChapterDucting Systems Examples Ducting Systems Examples Fireplace Furnace Operational Requirements Internal Thermostat Wood 4Chapter Fireplace Furnace Maintenance RequirementsOutside Combustion AIR Problem Cause Solution Troubleshooting GuideCombustion. Open your draft controls for up Replacement Parts Replacement Parts cont’d Part Drawings Ceramic Snap DISK, PP-91 THERMOSTAT, PP-563 Insulation for TOP, SIDES, FRONT, and BACK, PP-35 ASH Dump COVER, FP-0000-916 Yoke Bracket ASSEMBLY, FP-0000-923 Damper ROD ASSEMBLY, FP-0000-920 FP-33 & FP-37 Flue to HT Chimney ADAPTER, F-218 Grille BACK, FP-0000-33 Grille FRONT, FP-0000-32 AIR Intake GRILLE, PP-560 Adjustable Heat Discharge Boot OPTIONAL, FP-0000-925 LOG Grate optional, LG-900 Company Label Grate Warning Label Country Flame Technologies Required Warranty Information

Fireplace FP33, FP42, FP37 specifications

The Country Flame FP37, FP33, and FP42 fireplaces represent the pinnacle of modern heating technology, with each model expertly designed to meet the diverse demands of homeowners. These fireplaces offer not only warmth but also an aesthetic flair that enhances any living space.

The FP37 is renowned for its substantial heat output, making it an ideal option for larger areas. With a heating capacity of up to 2,800 square feet, it incorporates advanced combustion technology that ensures efficient fuel consumption while maximizing heat production. The innovative air wash system keeps the glass pane clear, providing a spectacular view of the dancing flames. Its multi-fuel capability allows users to burn wood, coal, or pellets, providing flexibility and convenience based on individual preferences.

In contrast, the FP33 is designed for smaller spaces without sacrificing performance. This compact model is capable of heating areas up to 2,000 square feet. Its efficient design promotes quick and easy installation, making it a favorite among homeowners looking for an effective heating solution with a smaller footprint. The FP33 features an adjustable firebox, enabling users to control the intensity of the flames and the heat output according to their needs, ensuring a cozy environment throughout the chilly months.

Meanwhile, the FP42 is a robust option for those seeking a powerful heating source. With a capacity to heat spaces exceeding 3,000 square feet, it features a larger firebox allowing for longer burn times and reduced refueling frequency. Like its counterparts, the FP42 employs a state-of-the-art catalytic converter that enhances burn efficiency and reduces harmful emissions, making it an environmentally responsible choice for heating.

All three models prioritize user-friendliness, with easy-to-use controls and straightforward maintenance. Their durable construction, designed to withstand high temperatures, ensures longevity and reliability. Additionally, all Country Flame fireplaces are backed by an industry-leading warranty, providing peace of mind for owners.

With sleek designs and a variety of options to suit different aesthetics, Country Flame FP37, FP33, and FP42 fireplaces truly embody the blend of functionality and beauty. Whether for a cozy living room or a spacious family area, these fireplaces guarantee a warm and inviting atmosphere, making them an exquisite addition to any home. Choosing any of these models means investing in quality warmth and unmatched comfort for years to come.
Top Page Image Contents