Vermont Casting DV580, DV360 manual Optional Top Vent Application, Complete conversion

Page 10

DV360/580 Series Direct Vent Gas Fireplace

Optional Top Vent Application

The DV360/580 fireplace is shipped as a rear vent unit. If the layout requires a top vent, convert the unit follow- ing the steps below.

1.Remove the 10 screws securing outer collar adapter to fireplace. (Fig. 11)

2.Set outer collar adapter aside.

3.Remove insulation from top of unit and discard. Re- move the four (4) screws securing flue cover to top of unit and remove flue cover. (Fig. 12)

4.Remove the four (4) screws securing flue pipe to back of unit. Remove flue pipe. (Fig. 12)

5.Secure flue cover to back of flue outlet. Be sure to replace gasket. (Fig. 14)

6.Install flue pipe and gasket removed in step 4 to top of unit with four (4) screws. Be sure to replace gas- ket. (Fig. 14)

7.Secure outer collar adapter to unit with the round collar on top, secure with 10 screws.

NOTE: Be sure not to damage any gasket material.

Outer

 

Collar

 

Adapter

 

Flue

 

 

Pipe

 

 

 

Remove

 

 

Screws

 

 

(5)

 

Remove Screws

 

(5)

 

FP1030

Fig. 11

Remove screws from outer collar adapter.

 

 

Insulation

 

Flue

 

 

Cover

 

 

Flue

 

Pipe

 

 

 

Remove

 

 

Screws

 

 

(4)

 

Remove Screws (4)

FP1027

 

 

Fig. 12

Remove flue cover and flue pipe.

 

10

 

 

CAUTION: Remove insulation. Insulation extends beyond opening in top of unit. Be sure to remove all insulation before completing conversion. Insulation measures 9¹⁄₄” x

22³⁄₄” (23.5 cm x 57.8 cm). If the unit is con- verted back to a rear vent, the insulation (Part number 20003129) must be replaced.

 

Flue Pipe

 

 

 

Replace

 

 

Screws (4)

Replace

 

Screws

 

(4)

 

 

 

Flue Cover

FP1028

 

 

Fig. 13

Replace flue cover and flue pipe.

 

FP1031

Fig. 14 Complete conversion.

After conversion to top vent configuration, the 4” (102 mm) flue pipe should be con- centric within the 7” (175 mm) outer collar.

20010667

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Direct Vent Gas Fireplace Table of Contents Installation & Operating Instructions Locating Your FireplaceFireplace Dimensions Installed as Top Vent DV360 DV580Fireplace Dimensions Installed as Rear Vent Framing DimensionsMantels Clearance to CombustiblesHearth Gas Specifications Framing And FinishingFinal Finishing Gas Inlet and Manifold PressuresAlternate Switch Location Gas Line InstallationRemote ON/OFF Switch Installation When purging gas line the front glass must be removedEB-1 Electrical Box Ensure that the power to the supply lineElectronic Gas Control Valve Optional Top Vent Application Complete conversionGeneral Venting Location of Vent TerminationCanadian Installations1 US Installations2 General Venting Information Termination LocationGeneral Information Assembling Vent Pipes Canadian InstallationsUSA Installations Flex Vent PipesTwist Lock Pipes How to Use the Vent GraphRear Wall Vent Application Rear Wall Vent Installation Twist Lock Pipe Zero clearance sleeve is only required for combustible wallsRear Wall Vent Installations Flex Vent Pipe Vertical Sidewall Application+ B = 17 Max Vertical Sidewall Installation Twist Lock Pipe Always install horizontal venting on a level planeVertical Sidewall Installation Flex Vent Pipe Horizontal length requirementBelow Grade Installation Vertical Through-the-Roof ApplicationVertical Through-the-Roof Installation Maximum elbow usageMin 610 mm Venting Components Operating Instructions DV360 Installation of LogsLog Identification Chart Logs DV360 DV580Log Rear Refer to Figure DV580Top logs must be placed properly onto notches Flame Characteristics Burner Lava Rock PlacementFlame & Temperature Adjustment Large Lava RockDV360 DV580Lighting and Operating Instructions To Turn Off Gas To HeaterTurning Off the Gas to the Appliance Lighting InstructionsValve in the on position On Manual Mode Shut Off ProcedureTransmitter Operation Off Mode Instructions for RF Comfort Control ValveFan Override During Auto Mode Delay Timer ModeAuto Mode Change Between F/C Temperature UnitsLED Count Service Action Auto PathOn Path Local Path Troubleshooting Honeywell VS8421 Remove Window Frame Assembly Before Service WorkTroubleshooting the Gas Control System SIT Nova 820 Millivolt ValveStart Troubleshooting the Gas Control System Burner Orifice Conversion DV360 Conversions must be completed by qualified personnelFuel Conversion Instructions Honeywell ValveUsing a 1/2 open end wrench remove the orifices. Fig Conversion Procedure Installation PrecautionsPilot Orifice Conversion Injector Orifice Size Matrix Logs May Be HOT MaintenanceCleaning the Standing Pilot Control System Burner and Burner CompartmentDV360/580 DV360/580 Description DV580 GACA4P0 Fuel Conversion Kits FK24 Fan Assembly Optional AccessoriesFK12 Fan Assembly Hard Direct Wire Hook UpCeramic Refractory Panels Remote ControlsInstallation Instructions Decorative Bay WindowsArch/Square Face Kit For Use in Mobile Homes Model DV360RMH Conversion Instructions9b.Units with Honeywell valve DV360/580 Series Direct Vent Gas Fireplace Limited Lifetime Warranty Efficiency Ratings AFUE%

DV580, DV360, DV360 specifications

Vermont Castings is a name synonymous with quality and craftsmanship in the world of fireplaces. Among their celebrated products, the DV580, DV360, and DV360 stand out for their advanced technology, efficiency, and aesthetic appeal. Each of these models offers unique features designed to enhance home heating while maintaining a focus on environmental responsibility.

The DV580 is a powerful direct vent gas stove that seamlessly combines traditional aesthetics with modern functionality. With its large viewing window, it creates a cozy ambiance while allowing users to enjoy the mesmerizing flames. One of its main features is the advanced burner system, which provides a realistic flame appearance. This model also boasts an impressive BTU output, allowing it to heat larger spaces efficiently. The unit is equipped with an electronic ignition, ensuring reliable start-ups even in cold weather.

The DV360, a slightly smaller but equally efficient model, offers versatility for various home settings. With its compact design, it can fit into tighter spaces without sacrificing heating capacity. The DV360 features a unique dual burner system, which promotes a more even and consistent flame. Its direct vent technology ensures that all combustion byproducts are vented outside, maintaining indoor air quality. This model also includes an adjustable flame height, giving users control over the intensity of the heat and ambiance.

In addition to performance, both the DV580 and DV360 prioritize energy efficiency. They are designed to operate with minimal emissions, making them an environmentally friendly choice for homeowners. With a variety of finish options and customizable face designs, these models can complement any home decor. Another key characteristic is the straightforward installation process, which allows homeowners the benefit of having their unit up and running in no time.

Overall, the Vermont Castings DV580, DV360, and DV360 models exemplify a harmonious blend of innovation, functionality, and style. They not only provide warmth but also contribute to the overall aesthetic of any space. With their commitment to quality and performance, Vermont Castings continues to set the standard for direct vent gas stoves, ensuring customers enjoy the best of both worlds: comfort and beauty in their homes.
Top Page Image Contents