Vermont Casting DV580, DV360 manual Operating Instructions

Page 24

DV360/580 Series Direct Vent Gas Fireplace

Operating Instructions

Glass Information

Only glass approved by CFM Corporation should be used on this fireplace.

• The use of any non-approved replace- ment glass will void all product warranties.

Care must be taken to avoid breakage of the glass.

Do not operate appliance with glass front re- moved, cracked or broken.

Replacement glass (complete with gasket) is available through your CFM Corporation dealer and should only be installed by a licensed quali- fied service person.

Louvre Removal

Window Frame

Assembly

Fireplace Front

Clamps

Glass

Panel

Glass

Panel

Pull Clamp

Hook

Push Clamp

Handle FP771a

To remove louvre assembly top, pull louvre up and then lift out. The louvre assembly bottom

2.

Fig. 47 Window frame assembly removal.

ed). After the initial cleaning process the glass should be cleaned two or three times during each operating

is hinged at the bottom edge and swings down. (Fig. 46)

1.

Louvre

season depending on the environment in the house.

Clean the glass after the first two weeks of operation.

Do not clean glass when hot.

Glass Panel

FP444

Fig. 46 Remove louvre assembly top.

Window Frame Assembly Removal

1.Turn the fireplace OFF (including the pilot).

2.If the unit has been operating, allow time for the components to cool.

3.Remove louvre assembly top.

4.Open the louvre assembly bottom.

5.Release the two clamps along lower edge of the frame by pulling down on clamp handles. (Fig. 47)

6.Tilt window frame assembly out slightly at the bot- tom, lift the frame up and away from the fireplace.

7.To replace window frame assembly reverse proce- dure.

Glass Cleaning

It is necessary to clean the glass periodically. During start-up condensation, which is normal, forms on the inside of the glass and causes lint, dust and other air- borne particles to cling to the glass surface. Also initial paint curing may deposit a slight film on the glass. It is therefore recommended the glass be cleaned two or three times with a non-ammonia household cleaner and warm water (gas fireplace glass cleaner is recommend-

Do not use abrasive cleaners.

Do not strike or slam the glass.

Installation of Optional Ceramic Panels

DV360

1.Remove glass.

2.Remove glass heat shield located at the top of the firebox toward the front.

3.Place the rear panel behind the rear log bracket.

4.Slide the right and left panels into place, The right and left panels will hold the rear panel in place when positioned properly.

5.Replace the glass heat shield.

6.Place the right and left hearth refractories and bring them together in the center and slide towards the front of the unit.

Replacement of

Ceramic Hearth Panels

1.Remove glass.

2.Set left and right panels on hearth and bring towards front of unit.

24

20010667

Image 24
Contents Direct Vent Gas Fireplace Table of Contents Installation & Operating Instructions Locating Your FireplaceFireplace Dimensions Installed as Top Vent DV360 DV580Fireplace Dimensions Installed as Rear Vent Framing DimensionsClearance to Combustibles MantelsHearth Framing And Finishing Final FinishingGas Specifications Gas Inlet and Manifold PressuresGas Line Installation Remote ON/OFF Switch InstallationAlternate Switch Location When purging gas line the front glass must be removedEnsure that the power to the supply line EB-1 Electrical BoxElectronic Gas Control Valve Optional Top Vent Application Complete conversionGeneral Venting Location of Vent TerminationCanadian Installations1 US Installations2 General Venting Information Termination LocationCanadian Installations USA InstallationsGeneral Information Assembling Vent Pipes Flex Vent PipesHow to Use the Vent Graph Twist Lock PipesRear Wall Vent Application Rear Wall Vent Installation Twist Lock Pipe Zero clearance sleeve is only required for combustible wallsRear Wall Vent Installations Flex Vent Pipe Vertical Sidewall Application+ B = 17 Max Vertical Sidewall Installation Twist Lock Pipe Always install horizontal venting on a level planeVertical Sidewall Installation Flex Vent Pipe Horizontal length requirementBelow Grade Installation Vertical Through-the-Roof ApplicationVertical Through-the-Roof Installation Maximum elbow usageMin 610 mm Venting Components Operating Instructions Installation of Logs Log Identification ChartDV360 Logs DV360 DV580Log Rear DV580 Refer to FigureTop logs must be placed properly onto notches Burner Lava Rock Placement Flame & Temperature AdjustmentFlame Characteristics Large Lava RockDV360 DV580Lighting and Operating Instructions To Turn Off Gas To HeaterLighting Instructions Turning Off the Gas to the ApplianceValve in the on position Shut Off Procedure Transmitter Operation Off ModeOn Manual Mode Instructions for RF Comfort Control ValveDelay Timer Mode Auto ModeFan Override During Auto Mode Change Between F/C Temperature UnitsLED Count Service Action Auto PathOn Path Local Path Troubleshooting Honeywell VS8421 Remove Window Frame Assembly Before Service WorkTroubleshooting the Gas Control System SIT Nova 820 Millivolt ValveStart Troubleshooting the Gas Control System Conversions must be completed by qualified personnel Fuel Conversion InstructionsBurner Orifice Conversion DV360 Honeywell ValveUsing a 1/2 open end wrench remove the orifices. Fig Installation Precautions Conversion ProcedurePilot Orifice Conversion Injector Orifice Size Matrix Maintenance Cleaning the Standing Pilot Control SystemLogs May Be HOT Burner and Burner CompartmentDV360/580 DV360/580 Description DV580 GACA4P0 Fuel Conversion Kits Optional Accessories FK12 Fan AssemblyFK24 Fan Assembly Hard Direct Wire Hook UpRemote Controls Installation InstructionsCeramic Refractory Panels Decorative Bay WindowsArch/Square Face Kit For Use in Mobile Homes Model DV360RMH Conversion Instructions9b.Units with Honeywell valve DV360/580 Series Direct Vent Gas Fireplace Limited Lifetime Warranty Efficiency Ratings AFUE%

DV580, DV360, DV360 specifications

Vermont Castings is a name synonymous with quality and craftsmanship in the world of fireplaces. Among their celebrated products, the DV580, DV360, and DV360 stand out for their advanced technology, efficiency, and aesthetic appeal. Each of these models offers unique features designed to enhance home heating while maintaining a focus on environmental responsibility.

The DV580 is a powerful direct vent gas stove that seamlessly combines traditional aesthetics with modern functionality. With its large viewing window, it creates a cozy ambiance while allowing users to enjoy the mesmerizing flames. One of its main features is the advanced burner system, which provides a realistic flame appearance. This model also boasts an impressive BTU output, allowing it to heat larger spaces efficiently. The unit is equipped with an electronic ignition, ensuring reliable start-ups even in cold weather.

The DV360, a slightly smaller but equally efficient model, offers versatility for various home settings. With its compact design, it can fit into tighter spaces without sacrificing heating capacity. The DV360 features a unique dual burner system, which promotes a more even and consistent flame. Its direct vent technology ensures that all combustion byproducts are vented outside, maintaining indoor air quality. This model also includes an adjustable flame height, giving users control over the intensity of the heat and ambiance.

In addition to performance, both the DV580 and DV360 prioritize energy efficiency. They are designed to operate with minimal emissions, making them an environmentally friendly choice for homeowners. With a variety of finish options and customizable face designs, these models can complement any home decor. Another key characteristic is the straightforward installation process, which allows homeowners the benefit of having their unit up and running in no time.

Overall, the Vermont Castings DV580, DV360, and DV360 models exemplify a harmonious blend of innovation, functionality, and style. They not only provide warmth but also contribute to the overall aesthetic of any space. With their commitment to quality and performance, Vermont Castings continues to set the standard for direct vent gas stoves, ensuring customers enjoy the best of both worlds: comfort and beauty in their homes.