Vermont Casting 1990 installation instructions Alcove Installations, Construction Requirements

Page 12

Intrepid II Woodburning Stove

Noncombustible shields installed 1” (25 mm) away from the combustible surface on noncombustible spacers, called ventilated shields, may be used to reduce clear- ances. (Fig. 14)

1" (25mm)

 

1/4" (6mm)

ST501

Fig. 14 A custom-formed mantel shield.

To protect a mantel from the heat of an Intrepid II in a fireplace installation, the ventilated mantel shield must be at least 48” (1220 mm) long, and it must be centered over the stove. Ventilated shields for side trim must extend the full length of the trim.

An unprotected mantel (‘A’, Fig. 15) cannot be more than 9” (230 mm) deep and must have a minimum clearance of 30” (760 mm), measured from the stove’s top plate. With a ventilated shield, this clearance may be reduced safely to 14” (360 mm).

Unprotected top trim (B) protruding 2” (50mm) or less from the face of the fireplace must be a minimum of 24” (610 mm) from the stove’s top surface. With a venti- lated trim shield, this clearance may be reduced safely to 14” (360 mm).

Unprotected side trim (C) that protrudes 2” (50mm) or less from the face of a fireplace must have a minimum clearance of 15” (380mm), measured from the stove’s top side edge. With a ventilated trim shield, the clear- ance may be reduced safely to 10” (254 mm). If the trim extends more than 2” (51 mm), wall clearance require- ments apply.

 

 

A

B

 

 

C

 

 

 

 

C

Fireplace Mantel and Trim Clearances ST253

Measured from the top and sides of the stove

 

Unprotected

Protected

A. Mantel

30”

(762 mm)

14”

(356 mm)

B. Top Trim

24”

(610 mm)

14”

(356 mm)

C. Side Trim

15”

(381 mm)

10”

(254 mm)

Fig. 15 Maintain clearances to combustible components of the mantelpiece.

Alcove Installations

Because of their restricted air flow and heat retention characteristics, specific construction requirements and special clearances apply to installations into alcoves. No stove or chimney connector heat shields are used in alcove installations.

ALCOVE INSTALLATION OF THE INTREPID II IS NOT PERMITTED IN CANADA.

Construction Requirements

The following illustrations show noncombustible ceiling framing and maximum and minimum permitted dimen- sions for alcove construction.

The charts and sample installations that follow list the clearances required for the various installation configu- rations of the Intrepid II.

36" Use recommended Max. floor protection

48" Min.

7/16” Durock® (or equivalent) spaced 1” off wood studs on noncombustible spacers

ST502

Fig. 16 Alcove floor plan. Sheetrock on front face butts to Durock® (or equivalent) alcove lining.

12

2000966

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Intrepid Table of Contents WelcomeSpecifications Intrepid II, ModelInstallation Outside AirWhat Kind of Chimney to Use Chimney Connector Guidelines Masonry ChimneysPrefabricated Chimneys Chimney SizeDouble-wall Chimney Connector Single-wall Chimney ConnectorSecuring the Single-wall Connector to a Masonry Chimney Freestanding Chimney InstallationsFireplace Chimney Installations Above a Fireplace Chimney connector enters chimney above the firepFireplace Chimney Installations Through a Fireplace Wall Pass-ThroughsFloor Protection An approved wall pass-through for CanadaFloor Protection for Fireplace Installations Reducing ClearancesChimney Connector Clearance Reductions Stove Heat ShieldsWall Shields Fireplace and Mantel Trim ShieldsAlcove Installations Construction RequirementsReflected ceiling plan Intrepid II Clearance Chart Intrepid II Clearance Diagrams 889 mm Parallel Installations Assembly Operation Attach the Griddle HandleYour Intrepid II’s Controls What They Do Damper Directs Air Flow Within the Stove Glass Door PanelsAndirons Two Ways to Add FuelBurn Only High-Quality Wood Surface Thermometer is a Valuable Guide to OperationUse the Air Control Settings that Work Best for You How to Build a Wood Fire Keep it GoingHigh-Efficiency Wood Burning With Catalytic Combustion Conditioning Your Stove Starting and Maintaining a Wood FireRefuel While the Embers are Still Hot Ash DisposalDraft Management Draft Testing CreosoteFuel Back-puffingMaintenance How to Adjust the Door Latch Damper AdjustmentTighten the Damper Handle as Needed Catalytic Combustion System Inspection and Cleaning When to Suspect a Combustion System ProblemReplace Refractory Package Replace the Stove Gaskets as NeededAdjust the Door if Necessary Annual MaintenancePermanent Gaskets Chimney System CreosoteIntrepid II Woodburning Stove Appendix Catalytic Combustor Intrepid II Woodburning Stove Intrepid II Woodburning Stove Please record the following information For future reference Intrepid II Woodburning Stove Intrepid II Woodburning Stove Warranty CFM Corporation

1990 specifications

Vermont Casting, founded in 1975, is renowned for its commitment to crafting high-quality cast iron wood stoves and heaters that merge efficiency with timeless design. By 1990, Vermont Casting had established itself as a leader in the industry, celebrated for its innovative approach to heating solutions and commitment to sustainability.

The 1990 models reflected an impressive evolution in technology and aesthetics. One of the standout features of Vermont Casting stoves was their utilization of advanced air control systems. This technology allowed users to regulate the burn speed and heat output effectively, making it easier to maintain consistent warmth in the home while optimizing fuel efficiency. The stoves featured an adjustable air inlet that provided users with the power to control combustion according to their needs.

In terms of design, Vermont Casting stoves were characterized by their iconic, rustic appearance, often featuring a choice of colors and finishes that allowed them to blend seamlessly into a variety of home aesthetics. The deep, rich finishes of the cast iron, coupled with elegant detailing, made each unit not only a heating appliance but also a centerpiece in living spaces. This commitment to aesthetics extended to the variety of designs available, including both traditional and modern styles, catering to diverse consumer preferences.

Vermont Casting also prioritized safety in their 1990 models. Many stoves were equipped with features such as double doors with glass panels, allowing users to enjoy the beauty of the flames while minimizing the risk of accidental burns. Some models incorporated heat shields that protected surrounding walls and furniture from excessive heat, further enhancing safety at home.

Durability was another hallmark of Vermont Casting’s reputation. The use of high-quality cast iron meant that these stoves were built to withstand years of use, often becoming familial heirlooms passed down through generations. In addition to resilience, cast iron was known for its ability to retain heat even after the fire had gone out, providing lingering warmth long into the night.

Overall, Vermont Casting in 1990 represented a harmonious blend of timeless design, advanced functionality, and a commitment to sustainability. Their stoves were not merely heating appliances but symbols of a lifestyle choice that emphasized quality, elegance, and environmental responsibility, making them a preferred choice for homeowners seeking both reliability and beauty in home heating solutions.
Top Page Image Contents