Vermont Casting 1990 Adjust the Door if Necessary, Permanent Gaskets, Chimney System Creosote

Page 31

5.Lay an unbroken 1/8” (3mm) bead of gasket cement in the newly-cleaned channel. Starting at one end, press the gasket into the channel. Ensure a good joint where the gasket meets before trimming any excess. Do not overlap the gasket ends or leave ends with ragged edges.

6.Press the gasketed part firmly against its normal mating surface to seat the gasket evenly in its chan- nel.

7.For doors, replace the doors and close them on a piece of waxed paper to keep the cement from migrating onto the stove front, or tap other parts with the rubber mallet (or hammer/block of wood).

8.Clean excess cement from around the channel. Let the cement that holds the new gasket dry thoroughly.

Adjust the Door if Necessary

The door latch or damper mechanism may need adjust- ment after you have regasketed them. Initially, it may require loosening to accommodate the new gasket; af- ter a few weeks, it may need tightening to compensate for compression of the new gasket. The directions for adjusting the latch and damper are on Page 27.

Permanent Gaskets

Other gaskets seal between non-moving parts, but these are not subject to the same wear and deteriora- tion as gaskets on moving parts. It is unlikely that you will ever need to replace these gaskets unless the involved parts are disassembled and then put back together. If this is the case, the job should be done only by a qualified service technician. The diameter of the gasket that seals these non-moving parts is 5/16”, and the areas sealed are the flue collar to the stove back; and the lower fireback to the sides. The glass panels use a special die-cut flat gasket; refer to Page 24 for information on these.

The Chimney System

Creosote

Your Intrepid II is designed to reduce creosote buildup significantly. However, regular chimney inspection and maintenance must still be performed. For safety, good stove performance, and to protect your chimney and chimney connector, inspect the chimney and chimney connector on a regular schedule. Clean the system if necessary. Failure to keep the chimney and connector system clean can result in a serious chimney fire.

When wood is burned slowly, it produces tar, organic vapors and moisture that combine to form creosote. The creosote vapors condense in the relatively cool chimney flue. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an

Intrepid II Woodburning Stove

extremely hot fire within the flue system that can dam- age the chimney and overheat adjacent combustible material.

If you do have a chimney fire, act promptly to:

•Close the damper and thermostat lever.

•Get everyone out of the house.

•Call the Fire department.

You should inspect the system every two weeks during the heating season as part of a regular maintenance schedule. To inspect the chimney, let the stove cool completely. Then, using a mirror and a strong light, sight up through the flue collar into the chimney flue. If it is not possible to inspect the flue system in this fashion the stove must be disconnected to provide better view- ing access.

If a significant layer of creosote has accumulated - 1/8” (3mm) or more - remove it to reduce the risk of a chim- ney fire.

Clean the chimney using a brush the same size and shape as the flue liner. Flexible fiberglass rods are used to run the brush up and down the liner, causing any deposits to fall to the bottom of the chimney where they can be removed through the clean out door.

The chimney connector should be cleaned by discon- necting the sections, taking them outside, and removing any deposits with a stiff wire brush. Reinstall the con- nector sections after cleaning, being sure to secure the individual sections with sheet metal screws.

If you cannot inspect or clean the chimney yourself, contact your local Vermont Castings authorized dealer or hire a professional chimney sweep.

Annual Maintenance

Perform a thorough cleaning, inspection and repair each spring, at the end of the heating season.

•Thoroughly clean the chimney and chimney connec- tor.

•Inspect the chimney for damage and deterioration. Replace weak sections of prefabricated chimney. Have a mason make repairs to a masonry chimney.

•Inspect the chimney connector and replace any damaged sections.

•Check gasketing for wear or compression, and replace if necessary. A ‘paper test’ will guide you on this. Close and lock the door or damper on a slip of paper and then try to pull the paper out. If the paper pulls out with little or no resistance, the gasket is not snug enough at that spot. If adjusting the damper or latch does not result in a seal that makes it hard to pull the paper out, replace the gasketing.

2000966

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Intrepid Welcome Table of ContentsIntrepid II, Model SpecificationsOutside Air InstallationWhat Kind of Chimney to Use Chimney Size Chimney Connector GuidelinesMasonry Chimneys Prefabricated ChimneysFreestanding Chimney Installations Double-wall Chimney ConnectorSingle-wall Chimney Connector Securing the Single-wall Connector to a Masonry ChimneyChimney connector enters chimney above the firep Fireplace Chimney Installations Above a FireplaceWall Pass-Throughs Fireplace Chimney Installations Through a FireplaceAn approved wall pass-through for Canada Floor ProtectionReducing Clearances Floor Protection for Fireplace InstallationsFireplace and Mantel Trim Shields Chimney Connector Clearance ReductionsStove Heat Shields Wall ShieldsConstruction Requirements Alcove InstallationsReflected ceiling plan Intrepid II Clearance Chart Intrepid II Clearance Diagrams 889 mm Parallel Installations Assembly Attach the Griddle Handle OperationYour Intrepid II’s Controls What They Do Two Ways to Add Fuel Damper Directs Air Flow Within the StoveGlass Door Panels AndironsSurface Thermometer is a Valuable Guide to Operation Burn Only High-Quality WoodHow to Build a Wood Fire Keep it Going Use the Air Control Settings that Work Best for YouHigh-Efficiency Wood Burning With Catalytic Combustion Starting and Maintaining a Wood Fire Conditioning Your StoveAsh Disposal Refuel While the Embers are Still HotDraft Management Back-puffing Draft TestingCreosote FuelMaintenance Damper Adjustment How to Adjust the Door LatchTighten the Damper Handle as Needed When to Suspect a Combustion System Problem Catalytic Combustion System Inspection and CleaningReplace the Stove Gaskets as Needed Replace Refractory PackageChimney System Creosote Adjust the Door if NecessaryAnnual Maintenance Permanent GasketsIntrepid II Woodburning Stove Appendix Catalytic Combustor Intrepid II Woodburning Stove Intrepid II Woodburning Stove Please record the following information For future reference Intrepid II Woodburning Stove Intrepid II Woodburning Stove Warranty CFM Corporation

1990 specifications

Vermont Casting, founded in 1975, is renowned for its commitment to crafting high-quality cast iron wood stoves and heaters that merge efficiency with timeless design. By 1990, Vermont Casting had established itself as a leader in the industry, celebrated for its innovative approach to heating solutions and commitment to sustainability.

The 1990 models reflected an impressive evolution in technology and aesthetics. One of the standout features of Vermont Casting stoves was their utilization of advanced air control systems. This technology allowed users to regulate the burn speed and heat output effectively, making it easier to maintain consistent warmth in the home while optimizing fuel efficiency. The stoves featured an adjustable air inlet that provided users with the power to control combustion according to their needs.

In terms of design, Vermont Casting stoves were characterized by their iconic, rustic appearance, often featuring a choice of colors and finishes that allowed them to blend seamlessly into a variety of home aesthetics. The deep, rich finishes of the cast iron, coupled with elegant detailing, made each unit not only a heating appliance but also a centerpiece in living spaces. This commitment to aesthetics extended to the variety of designs available, including both traditional and modern styles, catering to diverse consumer preferences.

Vermont Casting also prioritized safety in their 1990 models. Many stoves were equipped with features such as double doors with glass panels, allowing users to enjoy the beauty of the flames while minimizing the risk of accidental burns. Some models incorporated heat shields that protected surrounding walls and furniture from excessive heat, further enhancing safety at home.

Durability was another hallmark of Vermont Casting’s reputation. The use of high-quality cast iron meant that these stoves were built to withstand years of use, often becoming familial heirlooms passed down through generations. In addition to resilience, cast iron was known for its ability to retain heat even after the fire had gone out, providing lingering warmth long into the night.

Overall, Vermont Casting in 1990 represented a harmonious blend of timeless design, advanced functionality, and a commitment to sustainability. Their stoves were not merely heating appliances but symbols of a lifestyle choice that emphasized quality, elegance, and environmental responsibility, making them a preferred choice for homeowners seeking both reliability and beauty in home heating solutions.
Top Page Image Contents