Vermont Casting 1990 installation instructions Assembly

Page 18

Intrepid II Woodburning Stove

Assembly

Clean the Griddle Before Use

At the factory the griddle is coated with vegetable oil to prevent rusting while the stove is in transit and storage. Remove the oil with a dry rag or paper towel before you use the stove.

Set Up the Stove

Remove any loose parts from inside the stove. Place a protective pad on the floor, arrange some sections of 4 x 4 lumber on the pad for support, and carefully tip the stove onto them, on its back.

Remove and discard the four large slot-head screws from the stove bottom (Fig. 27) and install the stove legs, using the hex head bolts from the parts bag. Use 3/8” washers with three of the legs; the door/damper handle holder installs in place of a washer on the right front leg. Position the holder so the hole to accept the handle nub faces out from the right side of the stove. Tighten the bolts firmly.

Slotted

 

Screws

 

ST513

Fig. 27

Remove the slotted screws from the stove bottom.

Install the Bottom Heat Shield

A bottom heat shield must be used unless the stove is to be situated on a completely noncombustible hearth, such as unpainted concrete over earth. To install the bottom heat shield, loosen the leg bolts, and slip the bottom heat shield C-clips onto the bolts. Attach the bottom heat shield to the C-clips with the wing nuts, and tighten the leg bolts. Align the shield as shown in Figure 28.

10³⁄₄"

9³⁄₄"

ST512

Fig. 28 Attach bottom heat shield.

Storing the Handle

Use the removable handle to open or close the front doors, or to change the position of the damper. After using it, remove it so it won’t get hot, and store it in the handle holder installed behind the right front leg. (Fig. 29)

Door Handle Holder

Bottom Heat Shield

Bracket

Wing Bolt

ST514

Fig. 29 Handle holder and heat shield positions.

Reversing the Flue Collar

You can reverse the flue collar by removing the two screws that attach the collar to the back of the stove. (Fig. 30) Be sure the gasket around the flue collar opening is in position when you screw the collar back on to the stove.

18

2000966

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Intrepid Table of Contents WelcomeSpecifications Intrepid II, ModelInstallation Outside AirWhat Kind of Chimney to Use Prefabricated Chimneys Chimney Connector GuidelinesMasonry Chimneys Chimney SizeSecuring the Single-wall Connector to a Masonry Chimney Double-wall Chimney ConnectorSingle-wall Chimney Connector Freestanding Chimney InstallationsFireplace Chimney Installations Above a Fireplace Chimney connector enters chimney above the firepFireplace Chimney Installations Through a Fireplace Wall Pass-ThroughsFloor Protection An approved wall pass-through for CanadaFloor Protection for Fireplace Installations Reducing ClearancesWall Shields Chimney Connector Clearance ReductionsStove Heat Shields Fireplace and Mantel Trim ShieldsAlcove Installations Construction RequirementsReflected ceiling plan Intrepid II Clearance Chart Intrepid II Clearance Diagrams 889 mm Parallel Installations Assembly Operation Attach the Griddle HandleYour Intrepid II’s Controls What They Do Andirons Damper Directs Air Flow Within the StoveGlass Door Panels Two Ways to Add FuelBurn Only High-Quality Wood Surface Thermometer is a Valuable Guide to OperationUse the Air Control Settings that Work Best for You How to Build a Wood Fire Keep it GoingHigh-Efficiency Wood Burning With Catalytic Combustion Conditioning Your Stove Starting and Maintaining a Wood FireRefuel While the Embers are Still Hot Ash DisposalDraft Management Fuel Draft TestingCreosote Back-puffingMaintenance How to Adjust the Door Latch Damper AdjustmentTighten the Damper Handle as Needed Catalytic Combustion System Inspection and Cleaning When to Suspect a Combustion System ProblemReplace Refractory Package Replace the Stove Gaskets as NeededPermanent Gaskets Adjust the Door if NecessaryAnnual Maintenance Chimney System CreosoteIntrepid II Woodburning Stove Appendix Catalytic Combustor Intrepid II Woodburning Stove Intrepid II Woodburning Stove Please record the following information For future reference Intrepid II Woodburning Stove Intrepid II Woodburning Stove Warranty CFM Corporation

1990 specifications

Vermont Casting, founded in 1975, is renowned for its commitment to crafting high-quality cast iron wood stoves and heaters that merge efficiency with timeless design. By 1990, Vermont Casting had established itself as a leader in the industry, celebrated for its innovative approach to heating solutions and commitment to sustainability.

The 1990 models reflected an impressive evolution in technology and aesthetics. One of the standout features of Vermont Casting stoves was their utilization of advanced air control systems. This technology allowed users to regulate the burn speed and heat output effectively, making it easier to maintain consistent warmth in the home while optimizing fuel efficiency. The stoves featured an adjustable air inlet that provided users with the power to control combustion according to their needs.

In terms of design, Vermont Casting stoves were characterized by their iconic, rustic appearance, often featuring a choice of colors and finishes that allowed them to blend seamlessly into a variety of home aesthetics. The deep, rich finishes of the cast iron, coupled with elegant detailing, made each unit not only a heating appliance but also a centerpiece in living spaces. This commitment to aesthetics extended to the variety of designs available, including both traditional and modern styles, catering to diverse consumer preferences.

Vermont Casting also prioritized safety in their 1990 models. Many stoves were equipped with features such as double doors with glass panels, allowing users to enjoy the beauty of the flames while minimizing the risk of accidental burns. Some models incorporated heat shields that protected surrounding walls and furniture from excessive heat, further enhancing safety at home.

Durability was another hallmark of Vermont Casting’s reputation. The use of high-quality cast iron meant that these stoves were built to withstand years of use, often becoming familial heirlooms passed down through generations. In addition to resilience, cast iron was known for its ability to retain heat even after the fire had gone out, providing lingering warmth long into the night.

Overall, Vermont Casting in 1990 represented a harmonious blend of timeless design, advanced functionality, and a commitment to sustainability. Their stoves were not merely heating appliances but symbols of a lifestyle choice that emphasized quality, elegance, and environmental responsibility, making them a preferred choice for homeowners seeking both reliability and beauty in home heating solutions.
Top Page Image Contents