Vermont Casting 1990 Double-wall Chimney Connector, Single-wall Chimney Connector

Page 6

Intrepid II Woodburning Stove

Keep the horizontal run of chimney connector as short and direct as possible, with no more than two 90° turns. Slope horizontal runs of connector upward 1/4” per foot (20mm per m) going from the stove toward the chim- ney. The recommended maximum length of a horizontal run is 3’ (914mm). The recommended total length of chimney connector is 8’ (2.4m).

In cathedral ceiling installations, extend the prefabri- cated chimney down to within 8’ (2.4m) of the stove.

SAFETY NOTE: ALWAYS WEAR GLOVES AND PRO- TECTIVE EYEWEAR WHEN DRILLING, CUTTING OR JOINING SECTIONS OF CHIMNEY CONNECTOR.

Double-wall Chimney Connector

The listing for the Intrepid II for the U.S. and Canada includes use of double-wall chimney connectors that have been tested and listed for use with solid-fuel burn- ing appliances by a recognized testing laboratory.

Information on assembling and installing double-wall connector is provided by the manufacturer of the double-wall pipe. Follow the manufacturer’s instructions exactly as you assemble the connector and attach it to the stove and chimney. Using connectors and chim- neys from the same manufacturer makes the assembly and installation straightforward.

NOTE: For installations using double-wall con- nectors, minimum clearances must conform to the listed clearances in the clearance chart on Page 14.

Single-wall Chimney Connector

•Beginning at the flue collar of the stove, assemble the chimney connector. Insert the first crimped end into the stove’s flue collar, and keep each crimped end pointing toward the stove. Using the holes in the flue collar as guides, drill 1/8” (3mm) holes in the bottom of the first section of chimney connector and secure it to the flue collar with three #10 x 1/2”

sheet metal screws.

•Be sure the installed stove and chimney connector are correct distances from nearby combustible material.

NOTE: Special slip pipes and thimble sleeves that form telescoping joints between sections of chimney con- nector are available to simplify installations. They often eliminate the need to cut individual connector sections. Consult your local dealer about these special pieces.

Securing the Single-wall Connector to a

Prefabricated Chimney

For prefabricated chimneys, follow the installation instructions of the chimney maker exactly as you install the chimney. The maker of the chimney will supply the accessories to support the chimney, either from the roof of the house, at the ceiling of the room where the stove is installed, or from an exterior wall.

Special adapters are available from your local dealer to make the connection between the prefabricated chim- ney and the chimney connector. The top of such adapt- ers attaches directly to the chimney or to the chimney’s ceiling support package, while the bottom of the adap- tor is screwed to the chimney connector.

These adapters are designed so the top end will fit outside the inner wall of the chimney, and the bottom end will fit inside the first section of chimney connector. When assembled in this way, any soot or creosote fall- ing from the inner walls of the chimney will stay inside the chimney connector.

Securing the Single-wall Connector to a

Masonry Chimney

For masonry chimneys, both freestanding and fireplace chimneys may be used for installation of your Intrepid II.

Thimble Sleeve

Flue

Chimney

Connector

•Secure each joint be- tween sections of chimney connector, including tele- scoping joints, with at least three sheet metal screws. The pre-drilled holes in the top of each section of chimney connector serve as guides when you drill 1/8” (3mm) holes in the bottom of the next section.

•Secure the chimney connector to the chimney. Instructions for various installations follow.

Fig. 4 The crimped end of the connector points toward stove.

Keep sleeve end flush with flue tile

ST243

Fig. 5 The thimble, made of either ceramic or metal, must be cemented securely in place.

Freestanding Chimney Installations

If the chimney connector must pass through a combus- tible wall to reach the chimney, follow the recommenda- tions in the Wall Pass-through section that follows.

6

2000966

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Intrepid Table of Contents WelcomeSpecifications Intrepid II, ModelInstallation Outside AirWhat Kind of Chimney to Use Prefabricated Chimneys Chimney Connector GuidelinesMasonry Chimneys Chimney SizeSecuring the Single-wall Connector to a Masonry Chimney Double-wall Chimney ConnectorSingle-wall Chimney Connector Freestanding Chimney InstallationsFireplace Chimney Installations Above a Fireplace Chimney connector enters chimney above the firepFireplace Chimney Installations Through a Fireplace Wall Pass-ThroughsFloor Protection An approved wall pass-through for CanadaFloor Protection for Fireplace Installations Reducing ClearancesWall Shields Chimney Connector Clearance ReductionsStove Heat Shields Fireplace and Mantel Trim ShieldsAlcove Installations Construction RequirementsReflected ceiling plan Intrepid II Clearance Chart Intrepid II Clearance Diagrams 889 mm Parallel Installations Assembly Operation Attach the Griddle HandleYour Intrepid II’s Controls What They Do Andirons Damper Directs Air Flow Within the StoveGlass Door Panels Two Ways to Add FuelBurn Only High-Quality Wood Surface Thermometer is a Valuable Guide to OperationUse the Air Control Settings that Work Best for You How to Build a Wood Fire Keep it GoingHigh-Efficiency Wood Burning With Catalytic Combustion Conditioning Your Stove Starting and Maintaining a Wood FireRefuel While the Embers are Still Hot Ash DisposalDraft Management Fuel Draft TestingCreosote Back-puffingMaintenance How to Adjust the Door Latch Damper AdjustmentTighten the Damper Handle as Needed Catalytic Combustion System Inspection and Cleaning When to Suspect a Combustion System ProblemReplace Refractory Package Replace the Stove Gaskets as NeededPermanent Gaskets Adjust the Door if NecessaryAnnual Maintenance Chimney System CreosoteIntrepid II Woodburning Stove Appendix Catalytic Combustor Intrepid II Woodburning Stove Intrepid II Woodburning Stove Please record the following information For future reference Intrepid II Woodburning Stove Intrepid II Woodburning Stove Warranty CFM Corporation

1990 specifications

Vermont Casting, founded in 1975, is renowned for its commitment to crafting high-quality cast iron wood stoves and heaters that merge efficiency with timeless design. By 1990, Vermont Casting had established itself as a leader in the industry, celebrated for its innovative approach to heating solutions and commitment to sustainability.

The 1990 models reflected an impressive evolution in technology and aesthetics. One of the standout features of Vermont Casting stoves was their utilization of advanced air control systems. This technology allowed users to regulate the burn speed and heat output effectively, making it easier to maintain consistent warmth in the home while optimizing fuel efficiency. The stoves featured an adjustable air inlet that provided users with the power to control combustion according to their needs.

In terms of design, Vermont Casting stoves were characterized by their iconic, rustic appearance, often featuring a choice of colors and finishes that allowed them to blend seamlessly into a variety of home aesthetics. The deep, rich finishes of the cast iron, coupled with elegant detailing, made each unit not only a heating appliance but also a centerpiece in living spaces. This commitment to aesthetics extended to the variety of designs available, including both traditional and modern styles, catering to diverse consumer preferences.

Vermont Casting also prioritized safety in their 1990 models. Many stoves were equipped with features such as double doors with glass panels, allowing users to enjoy the beauty of the flames while minimizing the risk of accidental burns. Some models incorporated heat shields that protected surrounding walls and furniture from excessive heat, further enhancing safety at home.

Durability was another hallmark of Vermont Casting’s reputation. The use of high-quality cast iron meant that these stoves were built to withstand years of use, often becoming familial heirlooms passed down through generations. In addition to resilience, cast iron was known for its ability to retain heat even after the fire had gone out, providing lingering warmth long into the night.

Overall, Vermont Casting in 1990 represented a harmonious blend of timeless design, advanced functionality, and a commitment to sustainability. Their stoves were not merely heating appliances but symbols of a lifestyle choice that emphasized quality, elegance, and environmental responsibility, making them a preferred choice for homeowners seeking both reliability and beauty in home heating solutions.
Top Page Image Contents