Empire Comfort Systems VF24FP2-1, VF24FP3-1 Optional Blower Installation Instructions

Page 22

OPTIONAL BLOWER INSTALLATION INSTRUCTIONS

VFS-BK for Unvented Gas Fireplace Model VF24FP2-1, VF24FP3-1

INSTALLING OPTIONAL BLOWER VFS-BK

1.Lower bottom louver.

2.Remove screen front by lifting upward on screen front.

3.Remove top louver [(2) 8 x 1/2" Phillips screws].

4.Remove rear log support from inner casing [three (3) 10 x 1/2" screws.] (See Figure 1)

5.Remove three (3) 10 x 1/2" screws that attach burner assembly to inner bottom. (See Figure 1)

6.Remove six (6) 10 x 1/2" screws that attach inner casing to outer casing. Loosen two (2) 10 x 1/2" screws at interior, top of inner casing. Remove inner casing from outer casing by pivoting left side of inner casing. (See Figure 1)

Figure 1

7.For fireplace that is not installed, remove burner assembly from interior of fireplace.

7.For fireplace that is installed, burner assembly will remain with fireplace.

8.Insert blower assembly into left side of outer casing. Motor with wiring will be to inside of outer casing, blower chute will be facing upward. (See Figure 2)

9.Place and align two (2) orange motor mounting gaskets at rear of motor mounting brackets. Start two (2) 8 x 1/2" Phillips screws into motor mounting brackets and gaskets on side opposite motor. Start one (1) 8 x 1/2" Phillips screw into top motor mounting bracket and gasket adjacent to motor. Align and attach blower assembly to outer casing side. (See Figure 2)

10.Snap Heyco into blower shield side.

11.Place blower shield side adjacent to motor. Route blower motor wires through Heyco on blower shield side. (See Figure 3 and Figure 4)

12.Attach black wire from wire harness to OFF terminal on AUTO/OFF/ON switch.

13.Attach white/black wire from wire harness to ON terminal on AUTO/OFF/ON switch.

14.Attach black/red wire from wire harness to AUTO terminal on AUTO/OFF/ON switch.

Figure 2

15.Route two (2) flag terminals on wire harness through Heyco on blower shield side.

16.Attach two (2) flag terminals on wire harness to fan control (bracket).

17.Route cord set wires through access hole on right side of outer casing.

18.Insert strain relief in access hole on right side of outer casing.

19.Attach (1) pin terminal from black (hot) wire, smooth insulation on cord set to (1) socket terminal from black wire on AUTO/ OFF/ON switch.

20.Attach (1) pin terminal from black (neutral) wire, ribbed insulation on cord set to (1) socket terminal from black wire on motor.

21.Attach (1) pin terminal from white wire on AUTO/OFF/ON switch to (1) socket terminal from white wire on motor.

22.Attach green ground wires from wiring harness and cord set to interior back of outer casing with one (1) 8 x 1/2" Phillips screw.

Page 22

20248-2-0806

Image 22
Contents Installation Instructions Table of Contents Carbon Monoxide Poisoning MAY Lead to Important Safety InformationDo not Tamper with Pilot Light Safety DeathSafety Information for Users of LP-GAS LP-GAS Warning OdorIntroduction Specifications Water Vapor a BY-PRODUCT of Unvented Room HeatersVentilation AIR Ventilation Air From Inside BuildingOutdoors Ventilation Air From OutdoorsGAS Supply Recommended Gas Pipe DiameterClearances Combustible MaterialInstallation of Trim Installation of Fireplace Into MantelInstalling Fireplace in Mantel Rough Opening for Installing in Wall BUILT-IN Fireplace InstallationBuilt-In Fireplace Installation Rough Opening for Installing in CornerReplacement Loose Material glowing embers Part Number LOG PlacementPlacement of Glowing Embers Rock Wool Operation INSTRUCTIONS/FLAME AppearanceVF24FP3-1 Lighting Instructions What to do if YOU Smell GASVF24FP2-1 Lighting Instructions Lighting InstructionsVF24FP3-1 Pilot Pilot Flame CharacteristicsVF24FP2-1 Pilot VF24FP2-1 Bedroom Installation VF24FP2-1 OnlyMain Burner and Thermostat Operation VF24FP3-1 Main Burner OperationCheck 750 Millivolt System Operation Remote ReceiverAppliance produces unwanted odors Gas odor even when control knob is in OFF positionHeater produces a whistling noise when main burner is lit Appliance shuts off during use. Pilot stays onHOW to Order Repair Parts Parts ListIndex Part Description Number Parts View Installing Optional Brick Liner EHL-24-1 Optional Brick Liner Installation InstructionsParts List for EHL-24-1, Brick Liner KIT Optional Blower Installation Instructions Installing Optional Blower VFS-BK20248-2-0806 Optional Blower Installation Instructions VFS-BK Parts List WiringOiling Blower Motor Parts List and Parts View for Optional Trim Kits VPF24SS Stainless SteelService Notes