Enviro C-10791, 50-927 owner manual Fireplace is cool or use welder’s gloves or

Page 18

Initial Installation

QUALIFIED INSTALLERS ONLY

VENT CONFIGURATIONS AND RESTRICTOR SETTINGS:

Figures 23 shows the range of venting options, it shows possible vent configurations if the unit is top vented, for vertical and horizontal terminations, any layout that remains within the shaded area is acceptable. Having the fewest number of elbows is ideal, as they tend to disrupt air movement. Using 45˚ elbows is preferable to using 90˚ elbows. Also, a shorter vent system will perform better than a longer one.

The vent restrictor controls the amount of air moving through the vent pipe. Longer vertical vent lengths necessitate greater restriction; position 1 is open and position 5 is maximum restriction. Figure 23 shows the vent restrictor position required,

NOTE: The total length of the vent pipes can

relative to the length of vent pipe. The vent

not exceed 32 feet (15.12 m). Any combination

restrictor is located in the center of the

of rise and run can be used as long as it lays

fireplace, above the glass. Figure 24 shows

within the shaded area (a total of three (3) 90°

elbows or six (6) 45° elbows can be used).

the vent restrictor dial and the holes that

In addition to what is shown, if a 90°

indicate the different levels. To avoid injury,

elbow is used in the horizontal plane,

it is best to make this adjustment when the

3 feet (91.4 cm) must be subtracted

fireplace is cool or use welder’s gloves or

from the allowable horizontal run

(for each 45° elbow, 11⁄2 feet

oven mitts.

must be subtracted from the

Note: 0,0 in Figure 23 represents a 90˚

allowable horizontal run).

 

bend directly off the outlet of the unit, 413⁄4

 

inches (106 cm) from floor, in all horizontal

 

instances except when using Selkirk and

 

having less than a 4 feet (1.22 m) rise and

 

8 feet (2.44 m) horizontal offset. In this

 

case, a 1 foot (30.5 cm) rise must be added

 

below the 90˚ bend.

 

Note for rear vented: At 293⁄8 inches (75

 

cm) up, the maximum horizontal rear exit

 

vent length is 17 inches (43 cm) with a 45°

 

elbow (see Figure 12).

�� �� �

Figure 23. Possible Vent Configurations for Top Vented; Vertical Figure 24. Possible Vent Restrictor Positions. and Horizontal Terminations.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents For Your Safety R E C T V E N T F I R E P L a C ESafety Precautions GeneralTable of Contents Codes And Approvals Vented GAS Fireplace Heater DV36 NG/LPGThis Enviro DV36 Fireplace Specifications Installation OptionsFor Your Safety Read Before Operating InstructionsBlue, the fireplace is getting too much To Turn GAS Fireplace OFF Control PanelMaintenance And Service Never Operate Fireplace with the glass Removed Bottom latches for glassTo be Installed by a Qualified Service Agency only Initial Installation Qualified Installers onlyDo not interfere with the structural integrity of the walls Top of unit to bottom of 10 25.4 cm mantle Vent Termination Restrictions Venting 51mm 76mm 41 3/4 Fireplace is cool or use welder’s gloves or Possibility of a fire Horizontal Vent TerminationAssemble Vertical Vent TerminationRoof Pitch Minimum Height H Feet Meters Use of Wall Straps Installation of Electrical Wiring for the Optional FAN KIT GAS Line Connection To Test Valve PressuresSecondary Installation Empty firebox with grate and locator pinsThird Stage Log Set Installation Never operate the fireplace with the glass door removed Complete log set-up with embersTurn off the gas control knob and allow the unit to cool Is past the bottom of the baffle. Remove panel from fireboxKit Contents Installation of Kit Hook Fan Tabs Over Grommets at Unit BackTrouble Shooting Problem Possible Cause SolutionParts List Reference Part Description Part NumberParts Diagram Warranty To the DealerTo the Distributor Installation Data Sheet

50-927, C-10791 specifications

Enviro 50-927, also known as C-10791, represents a breakthrough in environmental technology designed to enhance sustainability and improve ecological balance. It is primarily aimed at industries with significant environmental footprints, such as manufacturing, transportation, and waste management.

At the heart of Enviro 50-927 is its advanced filtration system, which utilizes a multi-layered approach to isolate and neutralize harmful pollutants. The technology incorporates activated carbon, biofilters, and advanced polymer membranes that work synergistically to capture particulate matter, volatile organic compounds, and heavy metals. This comprehensive filtration process not only purifies air and water but also reduces the overall emissions footprint of industrial operations.

Another key feature of Enviro 50-927 is its smart monitoring technology. Equipped with IoT capabilities, it allows for real-time tracking and analytics of environmental parameters, facilitating proactive management of resources. Users can gain insights into the efficiency of operations, detect anomalies, and optimize processes, leading to reduced waste and energy consumption. This cloud-connected system enables seamless integration with existing Enterprise Resource Planning (ERP) systems, providing a holistic view of environmental impacts across operations.

Durability and resilience are significant characteristics of Enviro 50-927. Manufactured using high-grade, corrosion-resistant materials, it is designed to withstand harsh environmental conditions, making it ideal for both indoor and outdoor applications. Additionally, its compact design ensures that it can be installed in various settings without requiring extensive structural modifications.

Moreover, the installation and maintenance of Enviro 50-927 are user-friendly, requiring minimal downtime and expertise. This accessibility facilitates widespread adoption across different sectors, encouraging a shift towards sustainable practices and enhancing corporate social responsibility efforts.

In summary, Enviro 50-927, C-10791 showcases a blend of innovative technologies and user-centric design, setting a new standard for environmental management solutions. Its comprehensive features cater to evolving industry needs, promoting sustainability while maintaining operational efficiency. As companies increasingly prioritize eco-friendliness, products like Enviro 50-927 will be integral in meeting regulatory requirements and achieving sustainability goals.
Top Page Image Contents