Enviro C-10791, 50-927 owner manual Turn off the gas control knob and allow the unit to cool

Page 28

Secondary Installation

OPTIONAL CERAMIC BRICK PANEL INSTALLATION:

Figure 41. Back Panel In Place.

Turn off the gas control knob and allow the unit to cool.

Please ensure that your ceramic panels have not been damaged.

To Install Panels:

1.Remove the glass door by following the

instruction in the “SECONDARY INSTALLATION -

GLASS DOOR REMOVAl” section and remove logs if necessary.

2.Slide center brick panel up behind the baffle (shown in Figure 41) and rest the bottom of the panel on the ledge.

3.Using a flat head screwdriver, bend the top tabs on either side at the front of the baffle down (refer to Figure 43 for placement).

4.Slide the right panel along the side of the firebox until it is tight against the right side of the center panel. Ensure the panel is behind the top tab (see Figure 42).

5.Bend up the right bottom tab until it touches the bottom of the right panel (see Figure 44) and press

the top right tab tight against the top of the panel (see Figure 43).

6.Repeat steps 4 and 5 for the left panel.

7.Install the log set (refer to SECONDARY INSTALLATION - LOG SET

AND EMBER INSTALLATION) and glass door.

To Remove Panels:

1.Pull the bottom and top tabs away from the side panels.

2.Carefully slide the side panels out towards the front, do not slide the panels on the tabs.

3.Push the center panel straight up about 1⁄4 inch (1⁄2 cm), pull the bottom out past the ledge, then pull the panel down until it

is past the bottom of the baffle. Remove panel from firebox

Figure 42. Right Panel In Place.

 

 

 

 

Figure 43. Top Tab For Right Panel.

 

Figure 44. Bottom Tab For Right Panel.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents For Your Safety R E C T V E N T F I R E P L a C ESafety Precautions GeneralTable of Contents Vented GAS Fireplace Heater DV36 NG/LPG Codes And ApprovalsThis Enviro DV36 Fireplace Specifications Installation OptionsFor Your Safety Read Before Operating InstructionsBlue, the fireplace is getting too much To Turn GAS Fireplace OFF Control PanelMaintenance And Service Never Operate Fireplace with the glass Removed Bottom latches for glassTo be Installed by a Qualified Service Agency only Initial Installation Qualified Installers onlyDo not interfere with the structural integrity of the walls Top of unit to bottom of 10 25.4 cm mantle Vent Termination Restrictions Venting 51mm 76mm 41 3/4 Fireplace is cool or use welder’s gloves or Possibility of a fire Horizontal Vent TerminationAssemble Vertical Vent TerminationRoof Pitch Minimum Height H Feet Meters Use of Wall Straps Installation of Electrical Wiring for the Optional FAN KIT GAS Line Connection To Test Valve PressuresSecondary Installation Empty firebox with grate and locator pinsThird Stage Log Set Installation Never operate the fireplace with the glass door removed Complete log set-up with embersTurn off the gas control knob and allow the unit to cool Is past the bottom of the baffle. Remove panel from fireboxKit Contents Installation of Kit Hook Fan Tabs Over Grommets at Unit BackTrouble Shooting Problem Possible Cause SolutionParts List Reference Part Description Part NumberParts Diagram To the Dealer WarrantyTo the Distributor Installation Data Sheet

50-927, C-10791 specifications

Enviro 50-927, also known as C-10791, represents a breakthrough in environmental technology designed to enhance sustainability and improve ecological balance. It is primarily aimed at industries with significant environmental footprints, such as manufacturing, transportation, and waste management.

At the heart of Enviro 50-927 is its advanced filtration system, which utilizes a multi-layered approach to isolate and neutralize harmful pollutants. The technology incorporates activated carbon, biofilters, and advanced polymer membranes that work synergistically to capture particulate matter, volatile organic compounds, and heavy metals. This comprehensive filtration process not only purifies air and water but also reduces the overall emissions footprint of industrial operations.

Another key feature of Enviro 50-927 is its smart monitoring technology. Equipped with IoT capabilities, it allows for real-time tracking and analytics of environmental parameters, facilitating proactive management of resources. Users can gain insights into the efficiency of operations, detect anomalies, and optimize processes, leading to reduced waste and energy consumption. This cloud-connected system enables seamless integration with existing Enterprise Resource Planning (ERP) systems, providing a holistic view of environmental impacts across operations.

Durability and resilience are significant characteristics of Enviro 50-927. Manufactured using high-grade, corrosion-resistant materials, it is designed to withstand harsh environmental conditions, making it ideal for both indoor and outdoor applications. Additionally, its compact design ensures that it can be installed in various settings without requiring extensive structural modifications.

Moreover, the installation and maintenance of Enviro 50-927 are user-friendly, requiring minimal downtime and expertise. This accessibility facilitates widespread adoption across different sectors, encouraging a shift towards sustainable practices and enhancing corporate social responsibility efforts.

In summary, Enviro 50-927, C-10791 showcases a blend of innovative technologies and user-centric design, setting a new standard for environmental management solutions. Its comprehensive features cater to evolving industry needs, promoting sustainability while maintaining operational efficiency. As companies increasingly prioritize eco-friendliness, products like Enviro 50-927 will be integral in meeting regulatory requirements and achieving sustainability goals.
Top Page Image Contents